1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <i2c.h> 9 #include <hwconfig.h> 10 #include <asm/mmu.h> 11 #include <fsl_ddr_sdram.h> 12 #include <fsl_ddr_dimm_params.h> 13 #include <asm/fsl_law.h> 14 #include <asm/mpc85xx_gpio.h> 15 16 DECLARE_GLOBAL_DATA_PTR; 17 18 struct board_specific_parameters { 19 u32 n_ranks; 20 u32 datarate_mhz_high; 21 u32 rank_gb; 22 u32 clk_adjust; 23 u32 wrlvl_start; 24 u32 wrlvl_ctl_2; 25 u32 wrlvl_ctl_3; 26 }; 27 28 /* 29 * datarate_mhz_high values need to be in ascending order 30 */ 31 static const struct board_specific_parameters udimm0[] = { 32 /* 33 * memory controller 0 34 * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | 35 * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | 36 */ 37 #if defined(CONFIG_SYS_FSL_DDR4) 38 {2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,}, 39 {2, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,}, 40 {1, 1666, 0, 8, 6, 0x0708090B, 0x0C0D0E09,}, 41 {1, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,}, 42 {1, 2200, 0, 8, 7, 0x08090A0D, 0x0F0F100C,}, 43 #elif defined(CONFIG_SYS_FSL_DDR3) 44 {2, 833, 0, 8, 6, 0x06060607, 0x08080807,}, 45 {2, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,}, 46 {2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,}, 47 {1, 833, 0, 8, 6, 0x06060607, 0x08080807,}, 48 {1, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,}, 49 {1, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,}, 50 #else 51 #error DDR type not defined 52 #endif 53 {} 54 }; 55 56 static const struct board_specific_parameters *udimms[] = { 57 udimm0, 58 }; 59 60 void fsl_ddr_board_options(memctl_options_t *popts, 61 dimm_params_t *pdimm, 62 unsigned int ctrl_num) 63 { 64 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; 65 ulong ddr_freq; 66 struct cpu_type *cpu = gd->arch.cpu; 67 68 if (ctrl_num > 2) { 69 printf("Not supported controller number %d\n", ctrl_num); 70 return; 71 } 72 if (!pdimm->n_ranks) 73 return; 74 75 pbsp = udimms[0]; 76 77 /* Get clk_adjust according to the board ddr freqency and n_banks 78 * specified in board_specific_parameters table. 79 */ 80 ddr_freq = get_ddr_freq(0) / 1000000; 81 while (pbsp->datarate_mhz_high) { 82 if (pbsp->n_ranks == pdimm->n_ranks && 83 (pdimm->rank_density >> 30) >= pbsp->rank_gb) { 84 if (ddr_freq <= pbsp->datarate_mhz_high) { 85 popts->clk_adjust = pbsp->clk_adjust; 86 popts->wrlvl_start = pbsp->wrlvl_start; 87 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 88 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 89 goto found; 90 } 91 pbsp_highest = pbsp; 92 } 93 pbsp++; 94 } 95 96 if (pbsp_highest) { 97 printf("Error: board specific timing not found\n"); 98 printf("for data rate %lu MT/s\n", ddr_freq); 99 printf("Trying to use the highest speed (%u) parameters\n", 100 pbsp_highest->datarate_mhz_high); 101 popts->clk_adjust = pbsp_highest->clk_adjust; 102 popts->wrlvl_start = pbsp_highest->wrlvl_start; 103 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 104 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 105 } else { 106 panic("DIMM is not supported by this board"); 107 } 108 found: 109 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", 110 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); 111 debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ", 112 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2); 113 debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3); 114 115 /* 116 * Factors to consider for half-strength driver enable: 117 * - number of DIMMs installed 118 */ 119 popts->half_strength_driver_enable = 1; 120 /* 121 * Write leveling override 122 */ 123 popts->wrlvl_override = 1; 124 popts->wrlvl_sample = 0xf; 125 126 /* 127 * rtt and rtt_wr override 128 */ 129 popts->rtt_override = 0; 130 131 /* Enable ZQ calibration */ 132 popts->zq_en = 1; 133 134 /* DHC_EN =1, ODT = 75 Ohm */ 135 #ifdef CONFIG_SYS_FSL_DDR4 136 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm); 137 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) | 138 DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */ 139 #else 140 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); 141 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); 142 143 /* optimize cpo for erratum A-009942 */ 144 popts->cpo_sample = 0x5f; 145 #endif 146 147 /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit, 148 * set DDR bus width to 32bit for T1023 149 */ 150 if (cpu->soc_ver == SVR_T1023) 151 popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; 152 153 #ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32 154 /* for DDR bus 32bit test on T1024 */ 155 popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; 156 #endif 157 } 158 159 #if defined(CONFIG_DEEP_SLEEP) 160 void board_mem_sleep_setup(void) 161 { 162 void __iomem *qixis_base = (void *)QIXIS_BASE; 163 164 /* does not provide HW signals for power management */ 165 clrbits_8(qixis_base + 0x21, 0x2); 166 /* Disable MCKE isolation */ 167 gpio_set_value(2, 0); 168 udelay(1); 169 } 170 #endif 171 172 phys_size_t initdram(int board_type) 173 { 174 phys_size_t dram_size; 175 176 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) 177 puts("Initializing....using SPD\n"); 178 dram_size = fsl_ddr_sdram(); 179 #else 180 /* DDR has been initialised by first stage boot loader */ 181 dram_size = fsl_ddr_sdram_size(); 182 #endif 183 dram_size = setup_ddr_tlbs(dram_size / 0x100000); 184 dram_size *= 0x100000; 185 186 #if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD) 187 fsl_dp_resume(); 188 #endif 189 190 return dram_size; 191 } 192