1 /* 2 * Copyright 2010-2012 Freescale Semiconductor, Inc. 3 * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> 4 * Timur Tabi <timur@freescale.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <command.h> 11 #include <pci.h> 12 #include <asm/processor.h> 13 #include <asm/mmu.h> 14 #include <asm/cache.h> 15 #include <asm/immap_85xx.h> 16 #include <asm/fsl_pci.h> 17 #include <fsl_ddr_sdram.h> 18 #include <asm/fsl_serdes.h> 19 #include <asm/io.h> 20 #include <linux/libfdt.h> 21 #include <fdt_support.h> 22 #include <fsl_mdio.h> 23 #include <tsec.h> 24 #include <asm/fsl_law.h> 25 #include <netdev.h> 26 #include <i2c.h> 27 #include <hwconfig.h> 28 29 #include "../common/ngpixis.h" 30 31 DECLARE_GLOBAL_DATA_PTR; 32 33 int board_early_init_f(void) 34 { 35 ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; 36 37 /* Set pmuxcr to allow both i2c1 and i2c2 */ 38 setbits_be32(&gur->pmuxcr, 0x1000); 39 #ifdef CONFIG_SYS_RAMBOOT 40 setbits_be32(&gur->pmuxcr, 41 in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA); 42 #endif 43 44 /* Read back the register to synchronize the write. */ 45 in_be32(&gur->pmuxcr); 46 47 /* Set the pin muxing to enable ETSEC2. */ 48 clrbits_be32(&gur->pmuxcr2, 0x001F8000); 49 50 /* Enable the SPI */ 51 clrsetbits_8(&pixis->brdcfg0, PIXIS_ELBC_SPI_MASK, PIXIS_SPI); 52 53 return 0; 54 } 55 56 int checkboard(void) 57 { 58 u8 sw; 59 60 printf("Board: P1022DS Sys ID: 0x%02x, " 61 "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", 62 in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver)); 63 64 sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH)); 65 66 switch ((sw & PIXIS_LBMAP_MASK) >> 6) { 67 case 0: 68 printf ("vBank: %u\n", ((sw & 0x30) >> 4)); 69 break; 70 case 1: 71 printf ("NAND\n"); 72 break; 73 case 2: 74 case 3: 75 puts ("Promjet\n"); 76 break; 77 } 78 79 return 0; 80 } 81 82 #define CONFIG_TFP410_I2C_ADDR 0x38 83 84 /* Masks for the SSI_TDM and AUDCLK bits of the ngPIXIS BRDCFG1 register. */ 85 #define CONFIG_PIXIS_BRDCFG1_SSI_TDM_MASK 0x0c 86 #define CONFIG_PIXIS_BRDCFG1_AUDCLK_MASK 0x03 87 88 /* Route the I2C1 pins to the SSI port instead. */ 89 #define CONFIG_PIXIS_BRDCFG1_SSI_TDM_SSI 0x08 90 91 /* Choose the 12.288Mhz codec reference clock */ 92 #define CONFIG_PIXIS_BRDCFG1_AUDCLK_12 0x02 93 94 /* Choose the 11.2896Mhz codec reference clock */ 95 #define CONFIG_PIXIS_BRDCFG1_AUDCLK_11 0x01 96 97 /* Connect to USB2 */ 98 #define CONFIG_PIXIS_BRDCFG0_USB2 0x10 99 /* Connect to TFM bus */ 100 #define CONFIG_PIXIS_BRDCFG1_TDM 0x0c 101 /* Connect to SPI */ 102 #define CONFIG_PIXIS_BRDCFG0_SPI 0x80 103 104 int misc_init_r(void) 105 { 106 u8 temp; 107 const char *audclk; 108 size_t arglen; 109 ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 110 111 /* For DVI, enable the TFP410 Encoder. */ 112 113 temp = 0xBF; 114 if (i2c_write(CONFIG_TFP410_I2C_ADDR, 0x08, 1, &temp, sizeof(temp)) < 0) 115 return -1; 116 if (i2c_read(CONFIG_TFP410_I2C_ADDR, 0x08, 1, &temp, sizeof(temp)) < 0) 117 return -1; 118 debug("DVI Encoder Read: 0x%02x\n", temp); 119 120 temp = 0x10; 121 if (i2c_write(CONFIG_TFP410_I2C_ADDR, 0x0A, 1, &temp, sizeof(temp)) < 0) 122 return -1; 123 if (i2c_read(CONFIG_TFP410_I2C_ADDR, 0x0A, 1, &temp, sizeof(temp)) < 0) 124 return -1; 125 debug("DVI Encoder Read: 0x%02x\n",temp); 126 127 /* Enable the USB2 in PMUXCR2 and FGPA */ 128 if (hwconfig("usb2")) { 129 clrsetbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_ETSECUSB_MASK, 130 MPC85xx_PMUXCR2_USB); 131 setbits_8(&pixis->brdcfg0, CONFIG_PIXIS_BRDCFG0_USB2); 132 } 133 134 /* tdm and audio can not enable simultaneous*/ 135 if (hwconfig("tdm") && hwconfig("audclk")){ 136 printf("WARNING: TDM and AUDIO can not be enabled simultaneous !\n"); 137 return -1; 138 } 139 140 /* Enable the TDM in PMUXCR and FGPA */ 141 if (hwconfig("tdm")) { 142 clrsetbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_TDM_MASK, 143 MPC85xx_PMUXCR_TDM); 144 setbits_8(&pixis->brdcfg1, CONFIG_PIXIS_BRDCFG1_TDM); 145 /* TDM need some configration option by SPI */ 146 clrsetbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SPI_MASK, 147 MPC85xx_PMUXCR_SPI); 148 setbits_8(&pixis->brdcfg0, CONFIG_PIXIS_BRDCFG0_SPI); 149 } 150 151 /* 152 * Enable the reference clock for the WM8776 codec, and route the MUX 153 * pins for SSI. The default is the 12.288 MHz clock 154 */ 155 156 if (hwconfig("audclk")) { 157 temp = in_8(&pixis->brdcfg1) & ~(CONFIG_PIXIS_BRDCFG1_SSI_TDM_MASK | 158 CONFIG_PIXIS_BRDCFG1_AUDCLK_MASK); 159 temp |= CONFIG_PIXIS_BRDCFG1_SSI_TDM_SSI; 160 161 audclk = hwconfig_arg("audclk", &arglen); 162 /* Check the first two chars only */ 163 if (audclk && (strncmp(audclk, "11", 2) == 0)) 164 temp |= CONFIG_PIXIS_BRDCFG1_AUDCLK_11; 165 else 166 temp |= CONFIG_PIXIS_BRDCFG1_AUDCLK_12; 167 setbits_8(&pixis->brdcfg1, temp); 168 } 169 170 return 0; 171 } 172 173 /* 174 * A list of PCI and SATA slots 175 */ 176 enum slot_id { 177 SLOT_PCIE1 = 1, 178 SLOT_PCIE2, 179 SLOT_PCIE3, 180 SLOT_PCIE4, 181 SLOT_PCIE5, 182 SLOT_SATA1, 183 SLOT_SATA2 184 }; 185 186 /* 187 * This array maps the slot identifiers to their names on the P1022DS board. 188 */ 189 static const char *slot_names[] = { 190 [SLOT_PCIE1] = "Slot 1", 191 [SLOT_PCIE2] = "Slot 2", 192 [SLOT_PCIE3] = "Slot 3", 193 [SLOT_PCIE4] = "Slot 4", 194 [SLOT_PCIE5] = "Mini-PCIe", 195 [SLOT_SATA1] = "SATA 1", 196 [SLOT_SATA2] = "SATA 2", 197 }; 198 199 /* 200 * This array maps a given SERDES configuration and SERDES device to the PCI or 201 * SATA slot that it connects to. This mapping is hard-coded in the FPGA. 202 */ 203 static u8 serdes_dev_slot[][SATA2 + 1] = { 204 [0x01] = { [PCIE3] = SLOT_PCIE4, [PCIE2] = SLOT_PCIE5 }, 205 [0x02] = { [SATA1] = SLOT_SATA1, [SATA2] = SLOT_SATA2 }, 206 [0x09] = { [PCIE1] = SLOT_PCIE1, [PCIE3] = SLOT_PCIE4, 207 [PCIE2] = SLOT_PCIE5 }, 208 [0x16] = { [PCIE1] = SLOT_PCIE1, [PCIE3] = SLOT_PCIE2, 209 [PCIE2] = SLOT_PCIE3, 210 [SATA1] = SLOT_SATA1, [SATA2] = SLOT_SATA2 }, 211 [0x17] = { [PCIE1] = SLOT_PCIE1, [PCIE3] = SLOT_PCIE2, 212 [PCIE2] = SLOT_PCIE3 }, 213 [0x1a] = { [PCIE1] = SLOT_PCIE1, [PCIE2] = SLOT_PCIE3, 214 [PCIE2] = SLOT_PCIE3, 215 [SATA1] = SLOT_SATA1, [SATA2] = SLOT_SATA2 }, 216 [0x1c] = { [PCIE1] = SLOT_PCIE1, 217 [SATA1] = SLOT_SATA1, [SATA2] = SLOT_SATA2 }, 218 [0x1e] = { [PCIE1] = SLOT_PCIE1, [PCIE3] = SLOT_PCIE3 }, 219 [0x1f] = { [PCIE1] = SLOT_PCIE1 }, 220 }; 221 222 223 /* 224 * Returns the name of the slot to which the PCIe or SATA controller is 225 * connected 226 */ 227 const char *board_serdes_name(enum srds_prtcl device) 228 { 229 ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; 230 u32 pordevsr = in_be32(&gur->pordevsr); 231 unsigned int srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 232 MPC85xx_PORDEVSR_IO_SEL_SHIFT; 233 enum slot_id slot = serdes_dev_slot[srds_cfg][device]; 234 const char *name = slot_names[slot]; 235 236 if (name) 237 return name; 238 else 239 return "Nothing"; 240 } 241 242 #ifdef CONFIG_PCI 243 void pci_init_board(void) 244 { 245 fsl_pcie_init_board(0); 246 } 247 #endif 248 249 int board_early_init_r(void) 250 { 251 const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; 252 int flash_esel = find_tlb_idx((void *)flashbase, 1); 253 254 /* 255 * Remap Boot flash + PROMJET region to caching-inhibited 256 * so that flash can be erased properly. 257 */ 258 259 /* Flush d-cache and invalidate i-cache of any FLASH data */ 260 flush_dcache(); 261 invalidate_icache(); 262 263 if (flash_esel == -1) { 264 /* very unlikely unless something is messed up */ 265 puts("Error: Could not find TLB for FLASH BASE\n"); 266 flash_esel = 2; /* give our best effort to continue */ 267 } else { 268 /* invalidate existing TLB entry for flash + promjet */ 269 disable_tlb(flash_esel); 270 } 271 272 set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, 273 MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 274 0, flash_esel, BOOKE_PAGESZ_256M, 1); 275 276 return 0; 277 } 278 279 /* 280 * Initialize on-board and/or PCI Ethernet devices 281 * 282 * Returns: 283 * <0, error 284 * 0, no ethernet devices found 285 * >0, number of ethernet devices initialized 286 */ 287 int board_eth_init(bd_t *bis) 288 { 289 struct fsl_pq_mdio_info mdio_info; 290 struct tsec_info_struct tsec_info[2]; 291 unsigned int num = 0; 292 293 #ifdef CONFIG_TSEC1 294 SET_STD_TSEC_INFO(tsec_info[num], 1); 295 num++; 296 #endif 297 #ifdef CONFIG_TSEC2 298 SET_STD_TSEC_INFO(tsec_info[num], 2); 299 num++; 300 #endif 301 302 mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; 303 mdio_info.name = DEFAULT_MII_NAME; 304 fsl_pq_mdio_init(bis, &mdio_info); 305 306 return tsec_eth_init(bis, tsec_info, num) + pci_eth_init(bis); 307 } 308 309 #ifdef CONFIG_OF_BOARD_SETUP 310 /** 311 * ft_codec_setup - fix up the clock-frequency property of the codec node 312 * 313 * Update the clock-frequency property based on the value of the 'audclk' 314 * hwconfig option. If audclk is not specified, then don't write anything 315 * to the device tree, because it means that the codec clock is disabled. 316 */ 317 static void ft_codec_setup(void *blob, const char *compatible) 318 { 319 const char *audclk; 320 size_t arglen; 321 u32 freq; 322 323 audclk = hwconfig_arg("audclk", &arglen); 324 if (audclk) { 325 if (strncmp(audclk, "11", 2) == 0) 326 freq = 11289600; 327 else 328 freq = 12288000; 329 330 do_fixup_by_compat_u32(blob, compatible, "clock-frequency", 331 freq, 1); 332 } 333 } 334 335 int ft_board_setup(void *blob, bd_t *bd) 336 { 337 phys_addr_t base; 338 phys_size_t size; 339 340 ft_cpu_setup(blob, bd); 341 342 base = env_get_bootm_low(); 343 size = env_get_bootm_size(); 344 345 fdt_fixup_memory(blob, (u64)base, (u64)size); 346 347 #ifdef CONFIG_HAS_FSL_DR_USB 348 fsl_fdt_fixup_dr_usb(blob, bd); 349 #endif 350 351 FT_FSL_PCI_SETUP; 352 353 #ifdef CONFIG_FSL_SGMII_RISER 354 fsl_sgmii_riser_fdt_fixup(blob); 355 #endif 356 357 /* Update the WM8776 node's clock frequency property */ 358 ft_codec_setup(blob, "wlf,wm8776"); 359 360 return 0; 361 } 362 #endif 363