1 /* 2 * Copyright 2010 Freescale Semiconductor, Inc. 3 * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> 4 * Timur Tabi <timur@freescale.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 11 #include <asm/fsl_ddr_sdram.h> 12 #include <asm/fsl_ddr_dimm_params.h> 13 14 struct board_specific_parameters { 15 u32 n_ranks; 16 u32 datarate_mhz_high; 17 u32 clk_adjust; /* Range: 0-8 */ 18 u32 cpo; /* Range: 2-31 */ 19 u32 write_data_delay; /* Range: 0-6 */ 20 u32 force_2t; 21 }; 22 23 /* 24 * This table contains all valid speeds we want to override with board 25 * specific parameters. datarate_mhz_high values need to be in ascending order 26 * for each n_ranks group. 27 */ 28 static const struct board_specific_parameters dimm0[] = { 29 /* 30 * memory controller 0 31 * num| hi| clk| cpo|wrdata|2T 32 * ranks| mhz|adjst| | delay| 33 */ 34 {1, 549, 5, 31, 3, 0}, 35 {1, 850, 5, 31, 5, 0}, 36 {2, 549, 5, 31, 3, 0}, 37 {2, 850, 5, 31, 5, 0}, 38 {} 39 }; 40 41 void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm, 42 unsigned int ctrl_num) 43 { 44 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; 45 unsigned long ddr_freq; 46 unsigned int i; 47 48 49 if (ctrl_num) { 50 printf("Wrong parameter for controller number %d", ctrl_num); 51 return; 52 } 53 if (!pdimm->n_ranks) 54 return; 55 56 /* set odt_rd_cfg and odt_wr_cfg. */ 57 for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 58 popts->cs_local_opts[i].odt_rd_cfg = 0; 59 popts->cs_local_opts[i].odt_wr_cfg = 1; 60 } 61 62 pbsp = dimm0; 63 /* 64 * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr 65 * freqency and n_banks specified in board_specific_parameters table. 66 */ 67 ddr_freq = get_ddr_freq(0) / 1000000; 68 while (pbsp->datarate_mhz_high) { 69 if (pbsp->n_ranks == pdimm->n_ranks) { 70 if (ddr_freq <= pbsp->datarate_mhz_high) { 71 popts->clk_adjust = pbsp->clk_adjust; 72 popts->cpo_override = pbsp->cpo; 73 popts->write_data_delay = 74 pbsp->write_data_delay; 75 popts->twot_en = pbsp->force_2t; 76 goto found; 77 } 78 pbsp_highest = pbsp; 79 } 80 pbsp++; 81 } 82 83 if (pbsp_highest) { 84 printf("Error: board specific timing not found " 85 "for data rate %lu MT/s!\n" 86 "Trying to use the highest speed (%u) parameters\n", 87 ddr_freq, pbsp_highest->datarate_mhz_high); 88 popts->clk_adjust = pbsp->clk_adjust; 89 popts->cpo_override = pbsp->cpo; 90 popts->write_data_delay = pbsp->write_data_delay; 91 popts->twot_en = pbsp->force_2t; 92 } else { 93 panic("DIMM is not supported by this board"); 94 } 95 96 found: 97 popts->half_strength_driver_enable = 1; 98 99 /* Per AN4039, enable ZQ calibration. */ 100 popts->zq_en = 1; 101 102 /* 103 * For wake-up on ARP, we need auto self refresh enabled 104 */ 105 popts->auto_self_refresh_en = 1; 106 popts->sr_it = 0xb; 107 } 108