1 /*
2  * Copyright 2010-2011 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #include <common.h>
8 #include <asm/processor.h>
9 #include <asm/mmu.h>
10 #include <asm/cache.h>
11 #include <asm/immap_85xx.h>
12 #include <asm/io.h>
13 #include <miiphy.h>
14 #include <libfdt.h>
15 #include <fdt_support.h>
16 #include <fsl_mdio.h>
17 #include <tsec.h>
18 #include <mmc.h>
19 #include <netdev.h>
20 #include <pci.h>
21 #include <asm/fsl_serdes.h>
22 #include <fsl_ifc.h>
23 #include <asm/fsl_pci.h>
24 #include <hwconfig.h>
25 #include <i2c.h>
26 
27 DECLARE_GLOBAL_DATA_PTR;
28 
29 #define GPIO4_PCIE_RESET_SET		0x08000000
30 #define MUX_CPLD_CAN_UART		0x00
31 #define MUX_CPLD_TDM			0x01
32 #define MUX_CPLD_SPICS0_FLASH		0x00
33 #define MUX_CPLD_SPICS0_SLIC		0x02
34 #define PMUXCR1_IFC_MASK       0x00ffff00
35 #define PMUXCR1_SDHC_MASK      0x00fff000
36 #define PMUXCR1_SDHC_ENABLE    0x00555000
37 
38 enum {
39 	MUX_TYPE_IFC,
40 	MUX_TYPE_SDHC,
41 	MUX_TYPE_SPIFLASH,
42 	MUX_TYPE_TDM,
43 	MUX_TYPE_CAN,
44 	MUX_TYPE_CS0_NOR,
45 	MUX_TYPE_CS0_NAND,
46 };
47 
48 enum {
49 	I2C_READ_BANK,
50 	I2C_READ_PCB_VER,
51 };
52 
53 static uint sd_ifc_mux;
54 
55 struct cpld_data {
56 	u8 cpld_ver; /* cpld revision */
57 #if defined(CONFIG_TARGET_P1010RDB_PA)
58 	u8 pcba_ver; /* pcb revision number */
59 	u8 twindie_ddr3;
60 	u8 res1[6];
61 	u8 bank_sel; /* NOR Flash bank */
62 	u8 res2[5];
63 	u8 usb2_sel;
64 	u8 res3[1];
65 	u8 porsw_sel;
66 	u8 tdm_can_sel;
67 	u8 spi_cs0_sel; /* SPI CS0 SLIC/SPI Flash */
68 	u8 por0; /* POR Options */
69 	u8 por1; /* POR Options */
70 	u8 por2; /* POR Options */
71 	u8 por3; /* POR Options */
72 #elif defined(CONFIG_TARGET_P1010RDB_PB)
73 	u8 rom_loc;
74 #endif
75 };
76 
77 int board_early_init_f(void)
78 {
79 	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
80 	struct fsl_ifc ifc = {(void *)CONFIG_SYS_IFC_ADDR, (void *)NULL};
81 	/* Clock configuration to access CPLD using IFC(GPCM) */
82 	setbits_be32(&ifc.gregs->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT);
83 	/*
84 	* Reset PCIe slots via GPIO4
85 	*/
86 	setbits_be32(&pgpio->gpdir, GPIO4_PCIE_RESET_SET);
87 	setbits_be32(&pgpio->gpdat, GPIO4_PCIE_RESET_SET);
88 
89 	return 0;
90 }
91 
92 int board_early_init_r(void)
93 {
94 	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
95 	int flash_esel = find_tlb_idx((void *)flashbase, 1);
96 
97 	/*
98 	 * Remap Boot flash region to caching-inhibited
99 	 * so that flash can be erased properly.
100 	 */
101 
102 	/* Flush d-cache and invalidate i-cache of any FLASH data */
103 	flush_dcache();
104 	invalidate_icache();
105 
106 	if (flash_esel == -1) {
107 		/* very unlikely unless something is messed up */
108 		puts("Error: Could not find TLB for FLASH BASE\n");
109 		flash_esel = 2;	/* give our best effort to continue */
110 	} else {
111 		/* invalidate existing TLB entry for flash */
112 		disable_tlb(flash_esel);
113 	}
114 
115 	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
116 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
117 			0, flash_esel, BOOKE_PAGESZ_16M, 1);
118 
119 	set_tlb(1, flashbase + 0x1000000,
120 			CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000,
121 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
122 			0, flash_esel+1, BOOKE_PAGESZ_16M, 1);
123 	return 0;
124 }
125 
126 #ifdef CONFIG_PCI
127 void pci_init_board(void)
128 {
129 	fsl_pcie_init_board(0);
130 }
131 #endif /* ifdef CONFIG_PCI */
132 
133 int config_board_mux(int ctrl_type)
134 {
135 	ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
136 	u8 tmp;
137 
138 #if defined(CONFIG_TARGET_P1010RDB_PA)
139 	struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
140 
141 	switch (ctrl_type) {
142 	case MUX_TYPE_IFC:
143 		i2c_set_bus_num(I2C_PCA9557_BUS_NUM);
144 		tmp = 0xf0;
145 		i2c_write(I2C_PCA9557_ADDR1, 3, 1, &tmp, 1);
146 		tmp = 0x01;
147 		i2c_write(I2C_PCA9557_ADDR1, 1, 1, &tmp, 1);
148 		sd_ifc_mux = MUX_TYPE_IFC;
149 		clrbits_be32(&gur->pmuxcr, PMUXCR1_IFC_MASK);
150 		break;
151 	case MUX_TYPE_SDHC:
152 		i2c_set_bus_num(I2C_PCA9557_BUS_NUM);
153 		tmp = 0xf0;
154 		i2c_write(I2C_PCA9557_ADDR1, 3, 1, &tmp, 1);
155 		tmp = 0x05;
156 		i2c_write(I2C_PCA9557_ADDR1, 1, 1, &tmp, 1);
157 		sd_ifc_mux = MUX_TYPE_SDHC;
158 		clrsetbits_be32(&gur->pmuxcr, PMUXCR1_SDHC_MASK,
159 				PMUXCR1_SDHC_ENABLE);
160 		break;
161 	case MUX_TYPE_SPIFLASH:
162 		out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_FLASH);
163 		break;
164 	case MUX_TYPE_TDM:
165 		out_8(&cpld_data->tdm_can_sel, MUX_CPLD_TDM);
166 		out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_SLIC);
167 		break;
168 	case MUX_TYPE_CAN:
169 		out_8(&cpld_data->tdm_can_sel, MUX_CPLD_CAN_UART);
170 		break;
171 	default:
172 		break;
173 	}
174 #elif defined(CONFIG_TARGET_P1010RDB_PB)
175 	uint orig_bus = i2c_get_bus_num();
176 	i2c_set_bus_num(I2C_PCA9557_BUS_NUM);
177 
178 	switch (ctrl_type) {
179 	case MUX_TYPE_IFC:
180 		i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1);
181 		clrbits_8(&tmp, 0x04);
182 		i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1);
183 		i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
184 		clrbits_8(&tmp, 0x04);
185 		i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
186 		sd_ifc_mux = MUX_TYPE_IFC;
187 		clrbits_be32(&gur->pmuxcr, PMUXCR1_IFC_MASK);
188 		break;
189 	case MUX_TYPE_SDHC:
190 		i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1);
191 		setbits_8(&tmp, 0x04);
192 		i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1);
193 		i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
194 		clrbits_8(&tmp, 0x04);
195 		i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
196 		sd_ifc_mux = MUX_TYPE_SDHC;
197 		clrsetbits_be32(&gur->pmuxcr, PMUXCR1_SDHC_MASK,
198 				PMUXCR1_SDHC_ENABLE);
199 		break;
200 	case MUX_TYPE_SPIFLASH:
201 		i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1);
202 		clrbits_8(&tmp, 0x80);
203 		i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1);
204 		i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
205 		clrbits_8(&tmp, 0x80);
206 		i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
207 		break;
208 	case MUX_TYPE_TDM:
209 		i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1);
210 		setbits_8(&tmp, 0x82);
211 		i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1);
212 		i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
213 		clrbits_8(&tmp, 0x82);
214 		i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
215 		break;
216 	case MUX_TYPE_CAN:
217 		i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1);
218 		clrbits_8(&tmp, 0x02);
219 		i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1);
220 		i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
221 		clrbits_8(&tmp, 0x02);
222 		i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
223 		break;
224 	case MUX_TYPE_CS0_NOR:
225 		i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1);
226 		clrbits_8(&tmp, 0x08);
227 		i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1);
228 		i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
229 		clrbits_8(&tmp, 0x08);
230 		i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
231 		break;
232 	case MUX_TYPE_CS0_NAND:
233 		i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1);
234 		setbits_8(&tmp, 0x08);
235 		i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1);
236 		i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
237 		clrbits_8(&tmp, 0x08);
238 		i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1);
239 		break;
240 	default:
241 		break;
242 	}
243 	i2c_set_bus_num(orig_bus);
244 #endif
245 	return 0;
246 }
247 
248 #ifdef CONFIG_TARGET_P1010RDB_PB
249 int i2c_pca9557_read(int type)
250 {
251 	u8 val;
252 
253 	i2c_set_bus_num(I2C_PCA9557_BUS_NUM);
254 	i2c_read(I2C_PCA9557_ADDR2, 0, 1, &val, 1);
255 
256 	switch (type) {
257 	case I2C_READ_BANK:
258 		val = (val & 0x10) >> 4;
259 		break;
260 	case I2C_READ_PCB_VER:
261 		val = ((val & 0x60) >> 5) + 1;
262 		break;
263 	default:
264 		break;
265 	}
266 
267 	return val;
268 }
269 #endif
270 
271 int checkboard(void)
272 {
273 	struct cpu_type *cpu;
274 	struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
275 	u8 val;
276 
277 	cpu = gd->arch.cpu;
278 #if defined(CONFIG_TARGET_P1010RDB_PA)
279 	printf("Board: %sRDB-PA, ", cpu->name);
280 #elif defined(CONFIG_TARGET_P1010RDB_PB)
281 	printf("Board: %sRDB-PB, ", cpu->name);
282 	i2c_set_bus_num(I2C_PCA9557_BUS_NUM);
283 	i2c_init(CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE);
284 	val = 0x0;  /* no polarity inversion */
285 	i2c_write(I2C_PCA9557_ADDR2, 2, 1, &val, 1);
286 #endif
287 
288 #ifdef CONFIG_SDCARD
289 	/* switch to IFC to read info from CPLD */
290 	config_board_mux(MUX_TYPE_IFC);
291 #endif
292 
293 #if defined(CONFIG_TARGET_P1010RDB_PA)
294 	val = (in_8(&cpld_data->pcba_ver) & 0xf);
295 	printf("PCB: v%x.0\n", val);
296 #elif defined(CONFIG_TARGET_P1010RDB_PB)
297 	val = in_8(&cpld_data->cpld_ver);
298 	printf("CPLD: v%x.%x, ", val >> 4, val & 0xf);
299 	printf("PCB: v%x.0, ", i2c_pca9557_read(I2C_READ_PCB_VER));
300 	val = in_8(&cpld_data->rom_loc) & 0xf;
301 	puts("Boot from: ");
302 	switch (val) {
303 	case 0xf:
304 		config_board_mux(MUX_TYPE_CS0_NOR);
305 		printf("NOR vBank%d\n", i2c_pca9557_read(I2C_READ_BANK));
306 		break;
307 	case 0xe:
308 		puts("SDHC\n");
309 		val = 0x60; /* set pca9557 pin input/output */
310 		i2c_write(I2C_PCA9557_ADDR2, 3, 1, &val, 1);
311 		break;
312 	case 0x5:
313 		config_board_mux(MUX_TYPE_IFC);
314 		config_board_mux(MUX_TYPE_CS0_NAND);
315 		puts("NAND\n");
316 		break;
317 	case 0x6:
318 		config_board_mux(MUX_TYPE_IFC);
319 		puts("SPI\n");
320 		break;
321 	default:
322 		puts("unknown\n");
323 		break;
324 	}
325 #endif
326 	return 0;
327 }
328 
329 int board_eth_init(bd_t *bis)
330 {
331 #ifdef CONFIG_TSEC_ENET
332 	struct fsl_pq_mdio_info mdio_info;
333 	struct tsec_info_struct tsec_info[4];
334 	struct cpu_type *cpu;
335 	int num = 0;
336 
337 	cpu = gd->arch.cpu;
338 
339 #ifdef CONFIG_TSEC1
340 	SET_STD_TSEC_INFO(tsec_info[num], 1);
341 	num++;
342 #endif
343 #ifdef CONFIG_TSEC2
344 	SET_STD_TSEC_INFO(tsec_info[num], 2);
345 	num++;
346 #endif
347 #ifdef CONFIG_TSEC3
348 	/* P1014 and it's derivatives do not support eTSEC3 */
349 	if (cpu->soc_ver != SVR_P1014) {
350 		SET_STD_TSEC_INFO(tsec_info[num], 3);
351 		num++;
352 	}
353 #endif
354 	if (!num) {
355 		printf("No TSECs initialized\n");
356 		return 0;
357 	}
358 
359 	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
360 	mdio_info.name = DEFAULT_MII_NAME;
361 
362 	fsl_pq_mdio_init(bis, &mdio_info);
363 
364 	tsec_eth_init(bis, tsec_info, num);
365 #endif
366 
367 	return pci_eth_init(bis);
368 }
369 
370 #if defined(CONFIG_OF_BOARD_SETUP)
371 void fdt_del_flexcan(void *blob)
372 {
373 	int nodeoff = 0;
374 
375 	while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
376 				"fsl,p1010-flexcan")) >= 0) {
377 		fdt_del_node(blob, nodeoff);
378 	}
379 }
380 
381 void fdt_del_spi_flash(void *blob)
382 {
383 	int nodeoff = 0;
384 
385 	while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
386 				"spansion,s25sl12801")) >= 0) {
387 		fdt_del_node(blob, nodeoff);
388 	}
389 }
390 
391 void fdt_del_spi_slic(void *blob)
392 {
393 	int nodeoff = 0;
394 
395 	while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
396 				"zarlink,le88266")) >= 0) {
397 		fdt_del_node(blob, nodeoff);
398 	}
399 }
400 
401 void fdt_del_tdm(void *blob)
402 {
403 	int nodeoff = 0;
404 
405 	while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
406 				"fsl,starlite-tdm")) >= 0) {
407 		fdt_del_node(blob, nodeoff);
408 	}
409 }
410 
411 void fdt_del_sdhc(void *blob)
412 {
413 	int nodeoff = 0;
414 
415 	while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
416 			"fsl,esdhc")) >= 0) {
417 		fdt_del_node(blob, nodeoff);
418 	}
419 }
420 
421 void fdt_del_ifc(void *blob)
422 {
423 	int nodeoff = 0;
424 
425 	while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
426 				"fsl,ifc")) >= 0) {
427 		fdt_del_node(blob, nodeoff);
428 	}
429 }
430 
431 void fdt_disable_uart1(void *blob)
432 {
433 	int nodeoff;
434 
435 	nodeoff = fdt_node_offset_by_compat_reg(blob, "fsl,ns16550",
436 					CONFIG_SYS_NS16550_COM2);
437 
438 	if (nodeoff > 0) {
439 		fdt_status_disabled(blob, nodeoff);
440 	} else {
441 		printf("WARNING unable to set status for fsl,ns16550 "
442 			"uart1: %s\n", fdt_strerror(nodeoff));
443 	}
444 }
445 
446 int ft_board_setup(void *blob, bd_t *bd)
447 {
448 	phys_addr_t base;
449 	phys_size_t size;
450 	struct cpu_type *cpu;
451 
452 	cpu = gd->arch.cpu;
453 
454 	ft_cpu_setup(blob, bd);
455 
456 	base = env_get_bootm_low();
457 	size = env_get_bootm_size();
458 
459 #if defined(CONFIG_PCI)
460 	FT_FSL_PCI_SETUP;
461 #endif
462 
463 	fdt_fixup_memory(blob, (u64)base, (u64)size);
464 
465 #if defined(CONFIG_HAS_FSL_DR_USB)
466 	fsl_fdt_fixup_dr_usb(blob, bd);
467 #endif
468 
469        /* P1014 and it's derivatives don't support CAN and eTSEC3 */
470 	if (cpu->soc_ver == SVR_P1014) {
471 		fdt_del_flexcan(blob);
472 		fdt_del_node_and_alias(blob, "ethernet2");
473 	}
474 
475 	/* Delete IFC node as IFC pins are multiplexing with SDHC */
476 	if (sd_ifc_mux != MUX_TYPE_IFC)
477 		fdt_del_ifc(blob);
478 	else
479 		fdt_del_sdhc(blob);
480 
481 	if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) {
482 		fdt_del_tdm(blob);
483 		fdt_del_spi_slic(blob);
484 	} else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) {
485 		fdt_del_flexcan(blob);
486 		fdt_del_spi_flash(blob);
487 		fdt_disable_uart1(blob);
488 	} else {
489 		/*
490 		 * If we don't set fsl_p1010mux:tdm_can to "can" or "tdm"
491 		 * explicitly, defaultly spi_cs_sel to spi-flash instead of
492 		 * to tdm/slic.
493 		 */
494 		fdt_del_tdm(blob);
495 		fdt_del_flexcan(blob);
496 		fdt_disable_uart1(blob);
497 	}
498 
499 	return 0;
500 }
501 #endif
502 
503 #ifdef CONFIG_SDCARD
504 int board_mmc_init(bd_t *bis)
505 {
506 	config_board_mux(MUX_TYPE_SDHC);
507 		return -1;
508 }
509 #else
510 void board_reset(void)
511 {
512 	/* mux to IFC to enable CPLD for reset */
513 	if (sd_ifc_mux != MUX_TYPE_IFC)
514 		config_board_mux(MUX_TYPE_IFC);
515 }
516 #endif
517 
518 
519 int misc_init_r(void)
520 {
521 	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
522 
523 	if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) {
524 		clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN1_TDM |
525 				MPC85xx_PMUXCR_CAN1_UART |
526 				MPC85xx_PMUXCR_CAN2_TDM |
527 				MPC85xx_PMUXCR_CAN2_UART);
528 		config_board_mux(MUX_TYPE_CAN);
529 	} else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) {
530 		clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_UART |
531 				MPC85xx_PMUXCR_CAN1_UART);
532 		setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_TDM |
533 				MPC85xx_PMUXCR_CAN1_TDM);
534 		clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_GPIO);
535 		setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_TDM);
536 		config_board_mux(MUX_TYPE_TDM);
537 	} else {
538 		/* defaultly spi_cs_sel to flash */
539 		config_board_mux(MUX_TYPE_SPIFLASH);
540 	}
541 
542 	if (hwconfig("esdhc"))
543 		config_board_mux(MUX_TYPE_SDHC);
544 	else if (hwconfig("ifc"))
545 		config_board_mux(MUX_TYPE_IFC);
546 
547 #ifdef CONFIG_TARGET_P1010RDB_PB
548 	setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_GPIO01_DRVVBUS);
549 #endif
550 	return 0;
551 }
552 
553 static int pin_mux_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
554 				char * const argv[])
555 {
556 	if (argc < 2)
557 		return CMD_RET_USAGE;
558 	if (strcmp(argv[1], "ifc") == 0)
559 		config_board_mux(MUX_TYPE_IFC);
560 	else if (strcmp(argv[1], "sdhc") == 0)
561 		config_board_mux(MUX_TYPE_SDHC);
562 	else
563 		return CMD_RET_USAGE;
564 	return 0;
565 }
566 
567 U_BOOT_CMD(
568 	mux, 2, 0, pin_mux_cmd,
569 	"configure multiplexing pin for IFC/SDHC bus in runtime",
570 	"bus_type (e.g. mux sdhc)"
571 );
572