1 /* 2 * Copyright 2010-2011 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <asm/processor.h> 9 #include <asm/mmu.h> 10 #include <asm/cache.h> 11 #include <asm/immap_85xx.h> 12 #include <asm/io.h> 13 #include <miiphy.h> 14 #include <libfdt.h> 15 #include <fdt_support.h> 16 #include <fsl_mdio.h> 17 #include <tsec.h> 18 #include <mmc.h> 19 #include <netdev.h> 20 #include <pci.h> 21 #include <asm/fsl_serdes.h> 22 #include <fsl_ifc.h> 23 #include <asm/fsl_pci.h> 24 #include <hwconfig.h> 25 #include <i2c.h> 26 27 DECLARE_GLOBAL_DATA_PTR; 28 29 #define GPIO4_PCIE_RESET_SET 0x08000000 30 #define MUX_CPLD_CAN_UART 0x00 31 #define MUX_CPLD_TDM 0x01 32 #define MUX_CPLD_SPICS0_FLASH 0x00 33 #define MUX_CPLD_SPICS0_SLIC 0x02 34 #define PMUXCR1_IFC_MASK 0x00ffff00 35 #define PMUXCR1_SDHC_MASK 0x00fff000 36 #define PMUXCR1_SDHC_ENABLE 0x00555000 37 38 enum { 39 MUX_TYPE_IFC, 40 MUX_TYPE_SDHC, 41 MUX_TYPE_SPIFLASH, 42 MUX_TYPE_TDM, 43 MUX_TYPE_CAN, 44 MUX_TYPE_CS0_NOR, 45 MUX_TYPE_CS0_NAND, 46 }; 47 48 enum { 49 I2C_READ_BANK, 50 I2C_READ_PCB_VER, 51 }; 52 53 static uint sd_ifc_mux; 54 55 struct cpld_data { 56 u8 cpld_ver; /* cpld revision */ 57 #if defined(CONFIG_TARGET_P1010RDB_PA) 58 u8 pcba_ver; /* pcb revision number */ 59 u8 twindie_ddr3; 60 u8 res1[6]; 61 u8 bank_sel; /* NOR Flash bank */ 62 u8 res2[5]; 63 u8 usb2_sel; 64 u8 res3[1]; 65 u8 porsw_sel; 66 u8 tdm_can_sel; 67 u8 spi_cs0_sel; /* SPI CS0 SLIC/SPI Flash */ 68 u8 por0; /* POR Options */ 69 u8 por1; /* POR Options */ 70 u8 por2; /* POR Options */ 71 u8 por3; /* POR Options */ 72 #elif defined(CONFIG_TARGET_P1010RDB_PB) 73 u8 rom_loc; 74 #endif 75 }; 76 77 int board_early_init_f(void) 78 { 79 ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); 80 struct fsl_ifc ifc = {(void *)CONFIG_SYS_IFC_ADDR, (void *)NULL}; 81 /* Clock configuration to access CPLD using IFC(GPCM) */ 82 setbits_be32(&ifc.gregs->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT); 83 /* 84 * Reset PCIe slots via GPIO4 85 */ 86 setbits_be32(&pgpio->gpdir, GPIO4_PCIE_RESET_SET); 87 setbits_be32(&pgpio->gpdat, GPIO4_PCIE_RESET_SET); 88 89 return 0; 90 } 91 92 int board_early_init_r(void) 93 { 94 const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; 95 int flash_esel = find_tlb_idx((void *)flashbase, 1); 96 97 /* 98 * Remap Boot flash region to caching-inhibited 99 * so that flash can be erased properly. 100 */ 101 102 /* Flush d-cache and invalidate i-cache of any FLASH data */ 103 flush_dcache(); 104 invalidate_icache(); 105 106 if (flash_esel == -1) { 107 /* very unlikely unless something is messed up */ 108 puts("Error: Could not find TLB for FLASH BASE\n"); 109 flash_esel = 2; /* give our best effort to continue */ 110 } else { 111 /* invalidate existing TLB entry for flash */ 112 disable_tlb(flash_esel); 113 } 114 115 set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, 116 MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 117 0, flash_esel, BOOKE_PAGESZ_16M, 1); 118 119 set_tlb(1, flashbase + 0x1000000, 120 CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000, 121 MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 122 0, flash_esel+1, BOOKE_PAGESZ_16M, 1); 123 return 0; 124 } 125 126 #ifdef CONFIG_PCI 127 void pci_init_board(void) 128 { 129 fsl_pcie_init_board(0); 130 } 131 #endif /* ifdef CONFIG_PCI */ 132 133 int config_board_mux(int ctrl_type) 134 { 135 ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 136 u8 tmp; 137 138 #if defined(CONFIG_TARGET_P1010RDB_PA) 139 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 140 141 switch (ctrl_type) { 142 case MUX_TYPE_IFC: 143 i2c_set_bus_num(I2C_PCA9557_BUS_NUM); 144 tmp = 0xf0; 145 i2c_write(I2C_PCA9557_ADDR1, 3, 1, &tmp, 1); 146 tmp = 0x01; 147 i2c_write(I2C_PCA9557_ADDR1, 1, 1, &tmp, 1); 148 sd_ifc_mux = MUX_TYPE_IFC; 149 clrbits_be32(&gur->pmuxcr, PMUXCR1_IFC_MASK); 150 break; 151 case MUX_TYPE_SDHC: 152 i2c_set_bus_num(I2C_PCA9557_BUS_NUM); 153 tmp = 0xf0; 154 i2c_write(I2C_PCA9557_ADDR1, 3, 1, &tmp, 1); 155 tmp = 0x05; 156 i2c_write(I2C_PCA9557_ADDR1, 1, 1, &tmp, 1); 157 sd_ifc_mux = MUX_TYPE_SDHC; 158 clrsetbits_be32(&gur->pmuxcr, PMUXCR1_SDHC_MASK, 159 PMUXCR1_SDHC_ENABLE); 160 break; 161 case MUX_TYPE_SPIFLASH: 162 out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_FLASH); 163 break; 164 case MUX_TYPE_TDM: 165 out_8(&cpld_data->tdm_can_sel, MUX_CPLD_TDM); 166 out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_SLIC); 167 break; 168 case MUX_TYPE_CAN: 169 out_8(&cpld_data->tdm_can_sel, MUX_CPLD_CAN_UART); 170 break; 171 default: 172 break; 173 } 174 #elif defined(CONFIG_TARGET_P1010RDB_PB) 175 uint orig_bus = i2c_get_bus_num(); 176 i2c_set_bus_num(I2C_PCA9557_BUS_NUM); 177 178 switch (ctrl_type) { 179 case MUX_TYPE_IFC: 180 i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); 181 clrbits_8(&tmp, 0x04); 182 i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); 183 i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 184 clrbits_8(&tmp, 0x04); 185 i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 186 sd_ifc_mux = MUX_TYPE_IFC; 187 clrbits_be32(&gur->pmuxcr, PMUXCR1_IFC_MASK); 188 break; 189 case MUX_TYPE_SDHC: 190 i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); 191 setbits_8(&tmp, 0x04); 192 i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); 193 i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 194 clrbits_8(&tmp, 0x04); 195 i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 196 sd_ifc_mux = MUX_TYPE_SDHC; 197 clrsetbits_be32(&gur->pmuxcr, PMUXCR1_SDHC_MASK, 198 PMUXCR1_SDHC_ENABLE); 199 break; 200 case MUX_TYPE_SPIFLASH: 201 i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); 202 clrbits_8(&tmp, 0x80); 203 i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); 204 i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 205 clrbits_8(&tmp, 0x80); 206 i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 207 break; 208 case MUX_TYPE_TDM: 209 i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); 210 setbits_8(&tmp, 0x82); 211 i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); 212 i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 213 clrbits_8(&tmp, 0x82); 214 i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 215 break; 216 case MUX_TYPE_CAN: 217 i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); 218 clrbits_8(&tmp, 0x02); 219 i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); 220 i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 221 clrbits_8(&tmp, 0x02); 222 i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 223 break; 224 case MUX_TYPE_CS0_NOR: 225 i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); 226 clrbits_8(&tmp, 0x08); 227 i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); 228 i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 229 clrbits_8(&tmp, 0x08); 230 i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 231 break; 232 case MUX_TYPE_CS0_NAND: 233 i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); 234 setbits_8(&tmp, 0x08); 235 i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); 236 i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 237 clrbits_8(&tmp, 0x08); 238 i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); 239 break; 240 default: 241 break; 242 } 243 i2c_set_bus_num(orig_bus); 244 #endif 245 return 0; 246 } 247 248 #ifdef CONFIG_TARGET_P1010RDB_PB 249 int i2c_pca9557_read(int type) 250 { 251 u8 val; 252 253 i2c_set_bus_num(I2C_PCA9557_BUS_NUM); 254 i2c_read(I2C_PCA9557_ADDR2, 0, 1, &val, 1); 255 256 switch (type) { 257 case I2C_READ_BANK: 258 val = (val & 0x10) >> 4; 259 break; 260 case I2C_READ_PCB_VER: 261 val = ((val & 0x60) >> 5) + 1; 262 break; 263 default: 264 break; 265 } 266 267 return val; 268 } 269 #endif 270 271 int checkboard(void) 272 { 273 struct cpu_type *cpu; 274 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 275 u8 val; 276 277 cpu = gd->arch.cpu; 278 #if defined(CONFIG_TARGET_P1010RDB_PA) 279 printf("Board: %sRDB-PA, ", cpu->name); 280 #elif defined(CONFIG_TARGET_P1010RDB_PB) 281 printf("Board: %sRDB-PB, ", cpu->name); 282 i2c_set_bus_num(I2C_PCA9557_BUS_NUM); 283 i2c_init(CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE); 284 val = 0x0; /* no polarity inversion */ 285 i2c_write(I2C_PCA9557_ADDR2, 2, 1, &val, 1); 286 #endif 287 288 #ifdef CONFIG_SDCARD 289 /* switch to IFC to read info from CPLD */ 290 config_board_mux(MUX_TYPE_IFC); 291 #endif 292 293 #if defined(CONFIG_TARGET_P1010RDB_PA) 294 val = (in_8(&cpld_data->pcba_ver) & 0xf); 295 printf("PCB: v%x.0\n", val); 296 #elif defined(CONFIG_TARGET_P1010RDB_PB) 297 val = in_8(&cpld_data->cpld_ver); 298 printf("CPLD: v%x.%x, ", val >> 4, val & 0xf); 299 printf("PCB: v%x.0, ", i2c_pca9557_read(I2C_READ_PCB_VER)); 300 val = in_8(&cpld_data->rom_loc) & 0xf; 301 puts("Boot from: "); 302 switch (val) { 303 case 0xf: 304 config_board_mux(MUX_TYPE_CS0_NOR); 305 printf("NOR vBank%d\n", i2c_pca9557_read(I2C_READ_BANK)); 306 break; 307 case 0xe: 308 puts("SDHC\n"); 309 val = 0x60; /* set pca9557 pin input/output */ 310 i2c_write(I2C_PCA9557_ADDR2, 3, 1, &val, 1); 311 break; 312 case 0x5: 313 config_board_mux(MUX_TYPE_IFC); 314 config_board_mux(MUX_TYPE_CS0_NAND); 315 puts("NAND\n"); 316 break; 317 case 0x6: 318 config_board_mux(MUX_TYPE_IFC); 319 puts("SPI\n"); 320 break; 321 default: 322 puts("unknown\n"); 323 break; 324 } 325 #endif 326 return 0; 327 } 328 329 int board_eth_init(bd_t *bis) 330 { 331 #ifdef CONFIG_TSEC_ENET 332 struct fsl_pq_mdio_info mdio_info; 333 struct tsec_info_struct tsec_info[4]; 334 struct cpu_type *cpu; 335 int num = 0; 336 337 cpu = gd->arch.cpu; 338 339 #ifdef CONFIG_TSEC1 340 SET_STD_TSEC_INFO(tsec_info[num], 1); 341 num++; 342 #endif 343 #ifdef CONFIG_TSEC2 344 SET_STD_TSEC_INFO(tsec_info[num], 2); 345 num++; 346 #endif 347 #ifdef CONFIG_TSEC3 348 /* P1014 and it's derivatives do not support eTSEC3 */ 349 if (cpu->soc_ver != SVR_P1014) { 350 SET_STD_TSEC_INFO(tsec_info[num], 3); 351 num++; 352 } 353 #endif 354 if (!num) { 355 printf("No TSECs initialized\n"); 356 return 0; 357 } 358 359 mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; 360 mdio_info.name = DEFAULT_MII_NAME; 361 362 fsl_pq_mdio_init(bis, &mdio_info); 363 364 tsec_eth_init(bis, tsec_info, num); 365 #endif 366 367 return pci_eth_init(bis); 368 } 369 370 #if defined(CONFIG_OF_BOARD_SETUP) 371 void fdt_del_flexcan(void *blob) 372 { 373 int nodeoff = 0; 374 375 while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, 376 "fsl,p1010-flexcan")) >= 0) { 377 fdt_del_node(blob, nodeoff); 378 } 379 } 380 381 void fdt_del_spi_flash(void *blob) 382 { 383 int nodeoff = 0; 384 385 while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, 386 "spansion,s25sl12801")) >= 0) { 387 fdt_del_node(blob, nodeoff); 388 } 389 } 390 391 void fdt_del_spi_slic(void *blob) 392 { 393 int nodeoff = 0; 394 395 while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, 396 "zarlink,le88266")) >= 0) { 397 fdt_del_node(blob, nodeoff); 398 } 399 } 400 401 void fdt_del_tdm(void *blob) 402 { 403 int nodeoff = 0; 404 405 while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, 406 "fsl,starlite-tdm")) >= 0) { 407 fdt_del_node(blob, nodeoff); 408 } 409 } 410 411 void fdt_del_sdhc(void *blob) 412 { 413 int nodeoff = 0; 414 415 while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, 416 "fsl,esdhc")) >= 0) { 417 fdt_del_node(blob, nodeoff); 418 } 419 } 420 421 void fdt_del_ifc(void *blob) 422 { 423 int nodeoff = 0; 424 425 while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, 426 "fsl,ifc")) >= 0) { 427 fdt_del_node(blob, nodeoff); 428 } 429 } 430 431 void fdt_disable_uart1(void *blob) 432 { 433 int nodeoff; 434 435 nodeoff = fdt_node_offset_by_compat_reg(blob, "fsl,ns16550", 436 CONFIG_SYS_NS16550_COM2); 437 438 if (nodeoff > 0) { 439 fdt_status_disabled(blob, nodeoff); 440 } else { 441 printf("WARNING unable to set status for fsl,ns16550 " 442 "uart1: %s\n", fdt_strerror(nodeoff)); 443 } 444 } 445 446 int ft_board_setup(void *blob, bd_t *bd) 447 { 448 phys_addr_t base; 449 phys_size_t size; 450 struct cpu_type *cpu; 451 452 cpu = gd->arch.cpu; 453 454 ft_cpu_setup(blob, bd); 455 456 base = env_get_bootm_low(); 457 size = env_get_bootm_size(); 458 459 #if defined(CONFIG_PCI) 460 FT_FSL_PCI_SETUP; 461 #endif 462 463 fdt_fixup_memory(blob, (u64)base, (u64)size); 464 465 #if defined(CONFIG_HAS_FSL_DR_USB) 466 fsl_fdt_fixup_dr_usb(blob, bd); 467 #endif 468 469 /* P1014 and it's derivatives don't support CAN and eTSEC3 */ 470 if (cpu->soc_ver == SVR_P1014) { 471 fdt_del_flexcan(blob); 472 fdt_del_node_and_alias(blob, "ethernet2"); 473 } 474 475 /* Delete IFC node as IFC pins are multiplexing with SDHC */ 476 if (sd_ifc_mux != MUX_TYPE_IFC) 477 fdt_del_ifc(blob); 478 else 479 fdt_del_sdhc(blob); 480 481 if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) { 482 fdt_del_tdm(blob); 483 fdt_del_spi_slic(blob); 484 } else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) { 485 fdt_del_flexcan(blob); 486 fdt_del_spi_flash(blob); 487 fdt_disable_uart1(blob); 488 } else { 489 /* 490 * If we don't set fsl_p1010mux:tdm_can to "can" or "tdm" 491 * explicitly, defaultly spi_cs_sel to spi-flash instead of 492 * to tdm/slic. 493 */ 494 fdt_del_tdm(blob); 495 fdt_del_flexcan(blob); 496 fdt_disable_uart1(blob); 497 } 498 499 return 0; 500 } 501 #endif 502 503 #ifdef CONFIG_SDCARD 504 int board_mmc_init(bd_t *bis) 505 { 506 config_board_mux(MUX_TYPE_SDHC); 507 return -1; 508 } 509 #else 510 void board_reset(void) 511 { 512 /* mux to IFC to enable CPLD for reset */ 513 if (sd_ifc_mux != MUX_TYPE_IFC) 514 config_board_mux(MUX_TYPE_IFC); 515 } 516 #endif 517 518 519 int misc_init_r(void) 520 { 521 ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 522 523 if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) { 524 clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN1_TDM | 525 MPC85xx_PMUXCR_CAN1_UART | 526 MPC85xx_PMUXCR_CAN2_TDM | 527 MPC85xx_PMUXCR_CAN2_UART); 528 config_board_mux(MUX_TYPE_CAN); 529 } else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) { 530 clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_UART | 531 MPC85xx_PMUXCR_CAN1_UART); 532 setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_TDM | 533 MPC85xx_PMUXCR_CAN1_TDM); 534 clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_GPIO); 535 setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_TDM); 536 config_board_mux(MUX_TYPE_TDM); 537 } else { 538 /* defaultly spi_cs_sel to flash */ 539 config_board_mux(MUX_TYPE_SPIFLASH); 540 } 541 542 if (hwconfig("esdhc")) 543 config_board_mux(MUX_TYPE_SDHC); 544 else if (hwconfig("ifc")) 545 config_board_mux(MUX_TYPE_IFC); 546 547 #ifdef CONFIG_TARGET_P1010RDB_PB 548 setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_GPIO01_DRVVBUS); 549 #endif 550 return 0; 551 } 552 553 static int pin_mux_cmd(cmd_tbl_t *cmdtp, int flag, int argc, 554 char * const argv[]) 555 { 556 if (argc < 2) 557 return CMD_RET_USAGE; 558 if (strcmp(argv[1], "ifc") == 0) 559 config_board_mux(MUX_TYPE_IFC); 560 else if (strcmp(argv[1], "sdhc") == 0) 561 config_board_mux(MUX_TYPE_SDHC); 562 else 563 return CMD_RET_USAGE; 564 return 0; 565 } 566 567 U_BOOT_CMD( 568 mux, 2, 0, pin_mux_cmd, 569 "configure multiplexing pin for IFC/SDHC bus in runtime", 570 "bus_type (e.g. mux sdhc)" 571 ); 572