1 /* 2 * Copyright (C) 2014 Freescale Semiconductor, Inc. 3 * 4 * Author: Ye Li <ye.li@nxp.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <asm/arch/clock.h> 10 #include <asm/arch/crm_regs.h> 11 #include <asm/arch/iomux.h> 12 #include <asm/arch/imx-regs.h> 13 #include <asm/arch/mx6-pins.h> 14 #include <asm/arch/sys_proto.h> 15 #include <asm/gpio.h> 16 #include <asm/imx-common/iomux-v3.h> 17 #include <asm/imx-common/boot_mode.h> 18 #include <asm/io.h> 19 #include <asm/imx-common/mxc_i2c.h> 20 #include <linux/sizes.h> 21 #include <common.h> 22 #include <fsl_esdhc.h> 23 #include <mmc.h> 24 #include <i2c.h> 25 #include <miiphy.h> 26 #include <netdev.h> 27 #include <power/pmic.h> 28 #include <power/pfuze100_pmic.h> 29 #include "../common/pfuze.h" 30 #include <usb.h> 31 #include <usb/ehci-fsl.h> 32 #include <pca953x.h> 33 34 DECLARE_GLOBAL_DATA_PTR; 35 36 #define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 37 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 38 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 39 40 #define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 41 PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ 42 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 43 44 #define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 45 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 46 PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 47 PAD_CTL_ODE) 48 49 #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ 50 PAD_CTL_SPEED_HIGH | \ 51 PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST) 52 53 #define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ 54 PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) 55 56 #define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 57 PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST) 58 59 #define I2C_PMIC 1 60 61 #define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP) 62 #define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \ 63 PAD_CTL_SRE_FAST) 64 #define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1) 65 66 /*Define for building port exp gpio, pin starts from 0*/ 67 #define PORTEXP_IO_NR(chip, pin) \ 68 ((chip << 5) + pin) 69 70 /*Get the chip addr from a ioexp gpio*/ 71 #define PORTEXP_IO_TO_CHIP(gpio_nr) \ 72 (gpio_nr >> 5) 73 74 /*Get the pin number from a ioexp gpio*/ 75 #define PORTEXP_IO_TO_PIN(gpio_nr) \ 76 (gpio_nr & 0x1f) 77 78 #define CPU_PER_RST_B PORTEXP_IO_NR(0x30, 4) 79 #define STEER_ENET PORTEXP_IO_NR(0x32, 2) 80 81 static int port_exp_direction_output(unsigned gpio, int value) 82 { 83 int ret; 84 85 i2c_set_bus_num(2); 86 ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio)); 87 if (ret) 88 return ret; 89 90 ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio), 91 (1 << PORTEXP_IO_TO_PIN(gpio)), 92 (PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio))); 93 94 if (ret) 95 return ret; 96 97 ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio), 98 (1 << PORTEXP_IO_TO_PIN(gpio)), 99 (value << PORTEXP_IO_TO_PIN(gpio))); 100 101 if (ret) 102 return ret; 103 104 return 0; 105 } 106 107 int dram_init(void) 108 { 109 gd->ram_size = PHYS_SDRAM_SIZE; 110 111 return 0; 112 } 113 114 static iomux_v3_cfg_t const uart1_pads[] = { 115 MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), 116 MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), 117 }; 118 119 static iomux_v3_cfg_t const usdhc3_pads[] = { 120 MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 121 MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 122 MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 123 MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 124 MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 125 MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 126 MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 127 MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 128 MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 129 MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 130 131 /* CD pin */ 132 MX6_PAD_USB_H_DATA__GPIO7_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL), 133 134 /* RST_B, used for power reset cycle */ 135 MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), 136 }; 137 138 static iomux_v3_cfg_t const usdhc4_pads[] = { 139 MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 140 MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 141 MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 142 MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 143 MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 144 MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 145 MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 146 MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 147 MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 148 MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 149 150 /* CD pin */ 151 MX6_PAD_USB_H_STROBE__GPIO7_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), 152 }; 153 154 static iomux_v3_cfg_t const fec2_pads[] = { 155 MX6_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 156 MX6_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 157 MX6_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 158 MX6_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 159 MX6_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 160 MX6_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 161 MX6_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 162 MX6_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), 163 MX6_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), 164 MX6_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 165 MX6_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 166 MX6_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 167 MX6_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 168 MX6_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 169 }; 170 171 static void setup_iomux_uart(void) 172 { 173 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); 174 } 175 176 static int setup_fec(void) 177 { 178 struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 179 180 /* Use 125MHz anatop loopback REF_CLK1 for ENET2 */ 181 clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0); 182 183 return enable_fec_anatop_clock(1, ENET_125MHZ); 184 } 185 186 int board_eth_init(bd_t *bis) 187 { 188 int ret; 189 190 imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads)); 191 setup_fec(); 192 193 ret = fecmxc_initialize_multi(bis, 1, 194 CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE); 195 if (ret) 196 printf("FEC%d MXC: %s:failed\n", 1, __func__); 197 198 return ret; 199 } 200 201 int board_phy_config(struct phy_device *phydev) 202 { 203 /* 204 * Enable 1.8V(SEL_1P5_1P8_POS_REG) on 205 * Phy control debug reg 0 206 */ 207 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); 208 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); 209 210 /* rgmii tx clock delay enable */ 211 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); 212 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); 213 214 if (phydev->drv->config) 215 phydev->drv->config(phydev); 216 217 return 0; 218 } 219 220 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) 221 /* I2C2 for PMIC */ 222 struct i2c_pads_info i2c_pad_info2 = { 223 .scl = { 224 .i2c_mode = MX6_PAD_GPIO1_IO02__I2C2_SCL | PC, 225 .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO_2 | PC, 226 .gp = IMX_GPIO_NR(1, 2), 227 }, 228 .sda = { 229 .i2c_mode = MX6_PAD_GPIO1_IO03__I2C2_SDA | PC, 230 .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO_3 | PC, 231 .gp = IMX_GPIO_NR(1, 3), 232 }, 233 }; 234 235 /* I2C3 for IO Expander */ 236 struct i2c_pads_info i2c_pad_info3 = { 237 .scl = { 238 .i2c_mode = MX6_PAD_KEY_COL4__I2C3_SCL | PC, 239 .gpio_mode = MX6_PAD_KEY_COL4__GPIO2_IO_14 | PC, 240 .gp = IMX_GPIO_NR(2, 14), 241 }, 242 .sda = { 243 .i2c_mode = MX6_PAD_KEY_ROW4__I2C3_SDA | PC, 244 .gpio_mode = MX6_PAD_KEY_ROW4__GPIO2_IO_19 | PC, 245 .gp = IMX_GPIO_NR(2, 19), 246 }, 247 }; 248 249 int power_init_board(void) 250 { 251 struct pmic *p; 252 253 p = pfuze_common_init(I2C_PMIC); 254 if (!p) 255 return -ENODEV; 256 257 return 0; 258 } 259 260 #ifdef CONFIG_USB_EHCI_MX6 261 #define USB_OTHERREGS_OFFSET 0x800 262 #define UCTRL_PWR_POL (1 << 9) 263 264 static iomux_v3_cfg_t const usb_otg_pads[] = { 265 /* OGT1 */ 266 MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), 267 MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL), 268 /* OTG2 */ 269 MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL) 270 }; 271 272 static void setup_usb(void) 273 { 274 imx_iomux_v3_setup_multiple_pads(usb_otg_pads, 275 ARRAY_SIZE(usb_otg_pads)); 276 } 277 278 int board_usb_phy_mode(int port) 279 { 280 if (port == 1) 281 return USB_INIT_HOST; 282 else 283 return usb_phy_mode(port); 284 } 285 286 int board_ehci_hcd_init(int port) 287 { 288 u32 *usbnc_usb_ctrl; 289 290 if (port > 1) 291 return -EINVAL; 292 293 usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET + 294 port * 4); 295 296 /* Set Power polarity */ 297 setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL); 298 299 return 0; 300 } 301 #endif 302 303 int board_early_init_f(void) 304 { 305 setup_iomux_uart(); 306 307 return 0; 308 } 309 310 static struct fsl_esdhc_cfg usdhc_cfg[3] = { 311 {USDHC3_BASE_ADDR}, 312 {USDHC4_BASE_ADDR}, 313 }; 314 315 #define USDHC3_CD_GPIO IMX_GPIO_NR(7, 10) 316 #define USDHC3_RST_GPIO IMX_GPIO_NR(2, 11) 317 #define USDHC4_CD_GPIO IMX_GPIO_NR(7, 11) 318 319 int board_mmc_getcd(struct mmc *mmc) 320 { 321 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 322 int ret = 0; 323 324 switch (cfg->esdhc_base) { 325 case USDHC3_BASE_ADDR: 326 ret = !gpio_get_value(USDHC3_CD_GPIO); 327 break; 328 case USDHC4_BASE_ADDR: 329 ret = !gpio_get_value(USDHC4_CD_GPIO); 330 break; 331 } 332 333 return ret; 334 } 335 336 int board_mmc_init(bd_t *bis) 337 { 338 int i, ret; 339 340 /* 341 * According to the board_mmc_init() the following map is done: 342 * (U-Boot device node) (Physical Port) 343 * mmc0 USDHC3 344 * mmc1 USDHC4 345 */ 346 for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { 347 switch (i) { 348 case 0: 349 imx_iomux_v3_setup_multiple_pads( 350 usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); 351 gpio_direction_input(USDHC3_CD_GPIO); 352 353 /* This starts a power cycle for UHS-I. Need to set steer to B0 to A*/ 354 gpio_direction_output(USDHC3_RST_GPIO, 0); 355 udelay(1000); /* need 1ms at least */ 356 gpio_direction_output(USDHC3_RST_GPIO, 1); 357 358 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 359 break; 360 case 1: 361 imx_iomux_v3_setup_multiple_pads( 362 usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); 363 gpio_direction_input(USDHC4_CD_GPIO); 364 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); 365 break; 366 default: 367 printf("Warning: you configured more USDHC controllers" 368 "(%d) than supported by the board\n", i + 1); 369 return -EINVAL; 370 } 371 372 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); 373 if (ret) { 374 printf("Warning: failed to initialize mmc dev %d\n", i); 375 return ret; 376 } 377 } 378 379 return 0; 380 } 381 382 #ifdef CONFIG_FSL_QSPI 383 384 #define QSPI_PAD_CTRL1 \ 385 (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \ 386 PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm) 387 388 static iomux_v3_cfg_t const quadspi_pads[] = { 389 MX6_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 390 MX6_PAD_QSPI1A_SCLK__QSPI1_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 391 MX6_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 392 MX6_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 393 MX6_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 394 MX6_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 395 MX6_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 396 MX6_PAD_QSPI1B_SCLK__QSPI1_B_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 397 MX6_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 398 MX6_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 399 MX6_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 400 MX6_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), 401 }; 402 403 int board_qspi_init(void) 404 { 405 /* Set the iomux */ 406 imx_iomux_v3_setup_multiple_pads(quadspi_pads, 407 ARRAY_SIZE(quadspi_pads)); 408 409 /* Set the clock */ 410 enable_qspi_clk(0); 411 412 return 0; 413 } 414 #endif 415 416 #ifdef CONFIG_NAND_MXS 417 iomux_v3_cfg_t gpmi_pads[] = { 418 MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 419 MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 420 MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 421 MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL0), 422 MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 423 MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 424 MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 425 MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 426 MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 427 MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 428 MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 429 MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 430 MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 431 MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 432 MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), 433 }; 434 435 static void setup_gpmi_nand(void) 436 { 437 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 438 439 /* config gpmi nand iomux */ 440 imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads)); 441 442 setup_gpmi_io_clk((MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) | 443 MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) | 444 MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3))); 445 446 /* enable apbh clock gating */ 447 setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK); 448 } 449 #endif 450 451 int board_init(void) 452 { 453 /* Address of boot parameters */ 454 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 455 456 #ifdef CONFIG_SYS_I2C_MXC 457 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); 458 setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); 459 #endif 460 461 /* Reset CPU_PER_RST_B signal for enet phy and PCIE */ 462 port_exp_direction_output(CPU_PER_RST_B, 0); 463 udelay(500); 464 port_exp_direction_output(CPU_PER_RST_B, 1); 465 466 /* Set steering signal to L for selecting B0 */ 467 port_exp_direction_output(STEER_ENET, 0); 468 469 #ifdef CONFIG_USB_EHCI_MX6 470 setup_usb(); 471 #endif 472 473 #ifdef CONFIG_FSL_QSPI 474 board_qspi_init(); 475 #endif 476 477 #ifdef CONFIG_NAND_MXS 478 setup_gpmi_nand(); 479 #endif 480 481 return 0; 482 } 483 484 #ifdef CONFIG_CMD_BMODE 485 static const struct boot_mode board_boot_modes[] = { 486 {"sda", MAKE_CFGVAL(0x42, 0x30, 0x00, 0x00)}, 487 {"sdb", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, 488 {"qspi1", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)}, 489 {"nand", MAKE_CFGVAL(0x82, 0x00, 0x00, 0x00)}, 490 {NULL, 0}, 491 }; 492 #endif 493 494 int board_late_init(void) 495 { 496 #ifdef CONFIG_CMD_BMODE 497 add_board_boot_modes(board_boot_modes); 498 #endif 499 500 return 0; 501 } 502 503 int checkboard(void) 504 { 505 puts("Board: MX6SX SABRE AUTO\n"); 506 507 return 0; 508 } 509