1 /*
2  * Copyright (C) 2014 Freescale Semiconductor, Inc.
3  *
4  * Author: Ye Li <ye.li@nxp.com>
5  *
6  * SPDX-License-Identifier:	GPL-2.0+
7  */
8 
9 #include <asm/arch/clock.h>
10 #include <asm/arch/crm_regs.h>
11 #include <asm/arch/iomux.h>
12 #include <asm/arch/imx-regs.h>
13 #include <asm/arch/mx6-pins.h>
14 #include <asm/arch/sys_proto.h>
15 #include <asm/gpio.h>
16 #include <asm/imx-common/iomux-v3.h>
17 #include <asm/imx-common/boot_mode.h>
18 #include <asm/io.h>
19 #include <asm/imx-common/mxc_i2c.h>
20 #include <linux/sizes.h>
21 #include <common.h>
22 #include <fsl_esdhc.h>
23 #include <mmc.h>
24 #include <i2c.h>
25 #include <miiphy.h>
26 #include <netdev.h>
27 #include <power/pmic.h>
28 #include <power/pfuze100_pmic.h>
29 #include "../common/pfuze.h"
30 #include <usb.h>
31 #include <usb/ehci-fsl.h>
32 #include <pca953x.h>
33 
34 DECLARE_GLOBAL_DATA_PTR;
35 
36 #define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
37 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
38 	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
39 
40 #define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
41 	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
42 	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
43 
44 #define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
45 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
46 	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |			\
47 	PAD_CTL_ODE)
48 
49 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
50 	PAD_CTL_SPEED_HIGH   |                                   \
51 	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
52 
53 #define ENET_CLK_PAD_CTRL  (PAD_CTL_SPEED_MED | \
54 	PAD_CTL_DSE_120ohm   | PAD_CTL_SRE_FAST)
55 
56 #define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
57 	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
58 
59 #define I2C_PMIC	1
60 
61 #define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
62 #define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
63 			PAD_CTL_SRE_FAST)
64 #define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
65 
66 /*Define for building port exp gpio, pin starts from 0*/
67 #define PORTEXP_IO_NR(chip, pin) \
68 	((chip << 5) + pin)
69 
70 /*Get the chip addr from a ioexp gpio*/
71 #define PORTEXP_IO_TO_CHIP(gpio_nr) \
72 	(gpio_nr >> 5)
73 
74 /*Get the pin number from a ioexp gpio*/
75 #define PORTEXP_IO_TO_PIN(gpio_nr) \
76 	(gpio_nr & 0x1f)
77 
78 #define CPU_PER_RST_B	PORTEXP_IO_NR(0x30, 4)
79 #define STEER_ENET		PORTEXP_IO_NR(0x32, 2)
80 
81 static int port_exp_direction_output(unsigned gpio, int value)
82 {
83 	int ret;
84 
85 	i2c_set_bus_num(2);
86 	ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
87 	if (ret)
88 		return ret;
89 
90 	ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
91 		(1 << PORTEXP_IO_TO_PIN(gpio)),
92 		(PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
93 
94 	if (ret)
95 		return ret;
96 
97 	ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
98 		(1 << PORTEXP_IO_TO_PIN(gpio)),
99 		(value << PORTEXP_IO_TO_PIN(gpio)));
100 
101 	if (ret)
102 		return ret;
103 
104 	return 0;
105 }
106 
107 int dram_init(void)
108 {
109 	gd->ram_size = PHYS_SDRAM_SIZE;
110 
111 	return 0;
112 }
113 
114 static iomux_v3_cfg_t const uart1_pads[] = {
115 	MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
116 	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
117 };
118 
119 static iomux_v3_cfg_t const usdhc3_pads[] = {
120 	MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
121 	MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
122 	MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
123 	MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
124 	MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
125 	MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
126 	MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
127 	MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
128 	MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
129 	MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
130 
131 	/* CD pin */
132 	MX6_PAD_USB_H_DATA__GPIO7_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL),
133 
134 	/* RST_B, used for power reset cycle */
135 	MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
136 };
137 
138 static iomux_v3_cfg_t const usdhc4_pads[] = {
139 	MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
140 	MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
141 	MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
142 	MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
143 	MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
144 	MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
145 	MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
146 	MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
147 	MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
148 	MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
149 
150 	/* CD pin */
151 	MX6_PAD_USB_H_STROBE__GPIO7_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
152 };
153 
154 static iomux_v3_cfg_t const fec2_pads[] = {
155 	MX6_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
156 	MX6_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
157 	MX6_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
158 	MX6_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
159 	MX6_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
160 	MX6_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
161 	MX6_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
162 	MX6_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
163 	MX6_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
164 	MX6_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
165 	MX6_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
166 	MX6_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
167 	MX6_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
168 	MX6_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
169 };
170 
171 static void setup_iomux_uart(void)
172 {
173 	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
174 }
175 
176 static int setup_fec(void)
177 {
178 	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
179 
180 	/* Use 125MHz anatop loopback REF_CLK1 for ENET2 */
181 	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0);
182 
183 	return enable_fec_anatop_clock(1, ENET_125MHZ);
184 }
185 
186 int board_eth_init(bd_t *bis)
187 {
188 	int ret;
189 
190 	imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads));
191 	setup_fec();
192 
193 	ret = fecmxc_initialize_multi(bis, 1,
194 		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
195 	if (ret)
196 		printf("FEC%d MXC: %s:failed\n", 1, __func__);
197 
198 	return ret;
199 }
200 
201 int board_phy_config(struct phy_device *phydev)
202 {
203 	/*
204 	 * Enable 1.8V(SEL_1P5_1P8_POS_REG) on
205 	 * Phy control debug reg 0
206 	 */
207 	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
208 	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
209 
210 	/* rgmii tx clock delay enable */
211 	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
212 	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
213 
214 	if (phydev->drv->config)
215 		phydev->drv->config(phydev);
216 
217 	return 0;
218 }
219 
220 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
221 /* I2C2 for PMIC */
222 struct i2c_pads_info i2c_pad_info2 = {
223 	.scl = {
224 		.i2c_mode = MX6_PAD_GPIO1_IO02__I2C2_SCL | PC,
225 		.gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO_2 | PC,
226 		.gp = IMX_GPIO_NR(1, 2),
227 	},
228 	.sda = {
229 		.i2c_mode = MX6_PAD_GPIO1_IO03__I2C2_SDA | PC,
230 		.gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO_3 | PC,
231 		.gp = IMX_GPIO_NR(1, 3),
232 	},
233 };
234 
235 /* I2C3 for IO Expander */
236 struct i2c_pads_info i2c_pad_info3 = {
237 	.scl = {
238 		.i2c_mode = MX6_PAD_KEY_COL4__I2C3_SCL | PC,
239 		.gpio_mode = MX6_PAD_KEY_COL4__GPIO2_IO_14 | PC,
240 		.gp = IMX_GPIO_NR(2, 14),
241 	},
242 	.sda = {
243 		.i2c_mode = MX6_PAD_KEY_ROW4__I2C3_SDA | PC,
244 		.gpio_mode = MX6_PAD_KEY_ROW4__GPIO2_IO_19 | PC,
245 		.gp = IMX_GPIO_NR(2, 19),
246 	},
247 };
248 
249 int power_init_board(void)
250 {
251 	struct pmic *p;
252 
253 	p = pfuze_common_init(I2C_PMIC);
254 	if (!p)
255 		return -ENODEV;
256 
257 	return 0;
258 }
259 
260 #ifdef CONFIG_USB_EHCI_MX6
261 #define USB_OTHERREGS_OFFSET	0x800
262 #define UCTRL_PWR_POL		(1 << 9)
263 
264 static iomux_v3_cfg_t const usb_otg_pads[] = {
265 	/* OGT1 */
266 	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
267 	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
268 	/* OTG2 */
269 	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
270 };
271 
272 static void setup_usb(void)
273 {
274 	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
275 					 ARRAY_SIZE(usb_otg_pads));
276 }
277 
278 int board_usb_phy_mode(int port)
279 {
280 	if (port == 1)
281 		return USB_INIT_HOST;
282 	else
283 		return usb_phy_mode(port);
284 }
285 
286 int board_ehci_hcd_init(int port)
287 {
288 	u32 *usbnc_usb_ctrl;
289 
290 	if (port > 1)
291 		return -EINVAL;
292 
293 	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
294 				 port * 4);
295 
296 	/* Set Power polarity */
297 	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
298 
299 	return 0;
300 }
301 #endif
302 
303 int board_early_init_f(void)
304 {
305 	setup_iomux_uart();
306 
307 	return 0;
308 }
309 
310 static struct fsl_esdhc_cfg usdhc_cfg[3] = {
311 	{USDHC3_BASE_ADDR},
312 	{USDHC4_BASE_ADDR},
313 };
314 
315 #define USDHC3_CD_GPIO	IMX_GPIO_NR(7, 10)
316 #define USDHC3_RST_GPIO	IMX_GPIO_NR(2, 11)
317 #define USDHC4_CD_GPIO	IMX_GPIO_NR(7, 11)
318 
319 int board_mmc_getcd(struct mmc *mmc)
320 {
321 	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
322 	int ret = 0;
323 
324 	switch (cfg->esdhc_base) {
325 	case USDHC3_BASE_ADDR:
326 		ret = !gpio_get_value(USDHC3_CD_GPIO);
327 		break;
328 	case USDHC4_BASE_ADDR:
329 		ret = !gpio_get_value(USDHC4_CD_GPIO);
330 		break;
331 	}
332 
333 	return ret;
334 }
335 
336 int board_mmc_init(bd_t *bis)
337 {
338 	int i, ret;
339 
340 	/*
341 	 * According to the board_mmc_init() the following map is done:
342 	 * (U-Boot device node)    (Physical Port)
343 	 * mmc0                    USDHC3
344 	 * mmc1                    USDHC4
345 	 */
346 	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
347 		switch (i) {
348 		case 0:
349 			imx_iomux_v3_setup_multiple_pads(
350 				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
351 			gpio_direction_input(USDHC3_CD_GPIO);
352 
353 			/* This starts a power cycle for UHS-I. Need to set steer to B0 to A*/
354 			gpio_direction_output(USDHC3_RST_GPIO, 0);
355 			udelay(1000); /* need 1ms at least */
356 			gpio_direction_output(USDHC3_RST_GPIO, 1);
357 
358 			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
359 			break;
360 		case 1:
361 			imx_iomux_v3_setup_multiple_pads(
362 				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
363 			gpio_direction_input(USDHC4_CD_GPIO);
364 			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
365 			break;
366 		default:
367 			printf("Warning: you configured more USDHC controllers"
368 				"(%d) than supported by the board\n", i + 1);
369 			return -EINVAL;
370 			}
371 
372 			ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
373 			if (ret) {
374 				printf("Warning: failed to initialize mmc dev %d\n", i);
375 				return ret;
376 			}
377 	}
378 
379 	return 0;
380 }
381 
382 #ifdef CONFIG_FSL_QSPI
383 
384 #define QSPI_PAD_CTRL1	\
385 	(PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \
386 	 PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm)
387 
388 static iomux_v3_cfg_t const quadspi_pads[] = {
389 	MX6_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B   | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
390 	MX6_PAD_QSPI1A_SCLK__QSPI1_A_SCLK     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
391 	MX6_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
392 	MX6_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
393 	MX6_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
394 	MX6_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
395 	MX6_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B   | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
396 	MX6_PAD_QSPI1B_SCLK__QSPI1_B_SCLK     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
397 	MX6_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
398 	MX6_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
399 	MX6_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
400 	MX6_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
401 };
402 
403 int board_qspi_init(void)
404 {
405 	/* Set the iomux */
406 	imx_iomux_v3_setup_multiple_pads(quadspi_pads,
407 					 ARRAY_SIZE(quadspi_pads));
408 
409 	/* Set the clock */
410 	enable_qspi_clk(0);
411 
412 	return 0;
413 }
414 #endif
415 
416 #ifdef CONFIG_NAND_MXS
417 iomux_v3_cfg_t gpmi_pads[] = {
418 	MX6_PAD_NAND_CLE__RAWNAND_CLE		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
419 	MX6_PAD_NAND_ALE__RAWNAND_ALE		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
420 	MX6_PAD_NAND_WP_B__RAWNAND_WP_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
421 	MX6_PAD_NAND_READY_B__RAWNAND_READY_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL0),
422 	MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
423 	MX6_PAD_NAND_RE_B__RAWNAND_RE_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
424 	MX6_PAD_NAND_WE_B__RAWNAND_WE_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
425 	MX6_PAD_NAND_DATA00__RAWNAND_DATA00	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
426 	MX6_PAD_NAND_DATA01__RAWNAND_DATA01	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
427 	MX6_PAD_NAND_DATA02__RAWNAND_DATA02	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
428 	MX6_PAD_NAND_DATA03__RAWNAND_DATA03	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
429 	MX6_PAD_NAND_DATA04__RAWNAND_DATA04	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
430 	MX6_PAD_NAND_DATA05__RAWNAND_DATA05	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
431 	MX6_PAD_NAND_DATA06__RAWNAND_DATA06	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
432 	MX6_PAD_NAND_DATA07__RAWNAND_DATA07	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
433 };
434 
435 static void setup_gpmi_nand(void)
436 {
437 	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
438 
439 	/* config gpmi nand iomux */
440 	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
441 
442 	setup_gpmi_io_clk((MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) |
443 			MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) |
444 			MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3)));
445 
446 	/* enable apbh clock gating */
447 	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
448 }
449 #endif
450 
451 int board_init(void)
452 {
453 	/* Address of boot parameters */
454 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
455 
456 #ifdef CONFIG_SYS_I2C_MXC
457 	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
458 	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
459 #endif
460 
461 	/* Reset CPU_PER_RST_B signal for enet phy and PCIE */
462 	port_exp_direction_output(CPU_PER_RST_B, 0);
463 	udelay(500);
464 	port_exp_direction_output(CPU_PER_RST_B, 1);
465 
466 	/* Set steering signal to L for selecting B0 */
467 	port_exp_direction_output(STEER_ENET, 0);
468 
469 #ifdef CONFIG_USB_EHCI_MX6
470 	setup_usb();
471 #endif
472 
473 #ifdef CONFIG_FSL_QSPI
474 	board_qspi_init();
475 #endif
476 
477 #ifdef CONFIG_NAND_MXS
478 	setup_gpmi_nand();
479 #endif
480 
481 	return 0;
482 }
483 
484 #ifdef CONFIG_CMD_BMODE
485 static const struct boot_mode board_boot_modes[] = {
486 	{"sda", MAKE_CFGVAL(0x42, 0x30, 0x00, 0x00)},
487 	{"sdb", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
488 	{"qspi1", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)},
489 	{"nand", MAKE_CFGVAL(0x82, 0x00, 0x00, 0x00)},
490 	{NULL,	 0},
491 };
492 #endif
493 
494 int board_late_init(void)
495 {
496 #ifdef CONFIG_CMD_BMODE
497 	add_board_boot_modes(board_boot_modes);
498 #endif
499 
500 	return 0;
501 }
502 
503 int checkboard(void)
504 {
505 	puts("Board: MX6SX SABRE AUTO\n");
506 
507 	return 0;
508 }
509