1 /* 2 * Copyright (C) 2013 Freescale Semiconductor, Inc. 3 * 4 * Author: Fabio Estevam <fabio.estevam@freescale.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <asm/arch/clock.h> 10 #include <asm/arch/iomux.h> 11 #include <asm/arch/crm_regs.h> 12 #include <asm/arch/imx-regs.h> 13 #include <asm/arch/mx6-ddr.h> 14 #include <asm/arch/mx6-pins.h> 15 #include <asm/arch/sys_proto.h> 16 #include <asm/gpio.h> 17 #include <asm/imx-common/iomux-v3.h> 18 #include <asm/imx-common/mxc_i2c.h> 19 #include <asm/imx-common/spi.h> 20 #include <asm/io.h> 21 #include <linux/sizes.h> 22 #include <common.h> 23 #include <fsl_esdhc.h> 24 #include <i2c.h> 25 #include <mmc.h> 26 #include <netdev.h> 27 #include <power/pmic.h> 28 #include <power/pfuze100_pmic.h> 29 #include "../common/pfuze.h" 30 #include <usb.h> 31 #include <usb/ehci-ci.h> 32 33 DECLARE_GLOBAL_DATA_PTR; 34 35 #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 36 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 37 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 38 39 #define USDHC_PAD_CTRL (PAD_CTL_PUS_22K_UP | \ 40 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ 41 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 42 43 #define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 44 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 45 PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 46 47 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ 48 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 49 50 #define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 51 PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\ 52 PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \ 53 PAD_CTL_SRE_FAST) 54 55 #define ETH_PHY_POWER IMX_GPIO_NR(4, 21) 56 57 int dram_init(void) 58 { 59 gd->ram_size = imx_ddr_size(); 60 61 return 0; 62 } 63 64 static iomux_v3_cfg_t const uart1_pads[] = { 65 MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL), 66 MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL), 67 }; 68 69 #ifdef CONFIG_SPL_BUILD 70 static iomux_v3_cfg_t const usdhc1_pads[] = { 71 /* 8 bit SD */ 72 MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 73 MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 74 MX6_PAD_SD1_DAT0__USDHC1_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 75 MX6_PAD_SD1_DAT1__USDHC1_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 76 MX6_PAD_SD1_DAT2__USDHC1_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 77 MX6_PAD_SD1_DAT3__USDHC1_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 78 MX6_PAD_SD1_DAT4__USDHC1_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 79 MX6_PAD_SD1_DAT5__USDHC1_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 80 MX6_PAD_SD1_DAT6__USDHC1_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 81 MX6_PAD_SD1_DAT7__USDHC1_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 82 83 /*CD pin*/ 84 MX6_PAD_KEY_ROW7__GPIO_4_7 | MUX_PAD_CTRL(NO_PAD_CTRL), 85 }; 86 87 static iomux_v3_cfg_t const usdhc2_pads[] = { 88 MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 89 MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 90 MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 91 MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 92 MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 93 MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 94 95 /*CD pin*/ 96 MX6_PAD_SD2_DAT7__GPIO_5_0 | MUX_PAD_CTRL(NO_PAD_CTRL), 97 }; 98 99 static iomux_v3_cfg_t const usdhc3_pads[] = { 100 MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 101 MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 102 MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 103 MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 104 MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 105 MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 106 107 /*CD pin*/ 108 MX6_PAD_REF_CLK_32K__GPIO_3_22 | MUX_PAD_CTRL(NO_PAD_CTRL), 109 }; 110 #endif 111 112 static iomux_v3_cfg_t const fec_pads[] = { 113 MX6_PAD_FEC_MDC__FEC_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 114 MX6_PAD_FEC_MDIO__FEC_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 115 MX6_PAD_FEC_CRS_DV__FEC_RX_DV | MUX_PAD_CTRL(ENET_PAD_CTRL), 116 MX6_PAD_FEC_RXD0__FEC_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 117 MX6_PAD_FEC_RXD1__FEC_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 118 MX6_PAD_FEC_TX_EN__FEC_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), 119 MX6_PAD_FEC_TXD0__FEC_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 120 MX6_PAD_FEC_TXD1__FEC_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 121 MX6_PAD_FEC_REF_CLK__FEC_REF_OUT | MUX_PAD_CTRL(ENET_PAD_CTRL), 122 MX6_PAD_FEC_RX_ER__GPIO_4_19 | MUX_PAD_CTRL(NO_PAD_CTRL), 123 MX6_PAD_FEC_TX_CLK__GPIO_4_21 | MUX_PAD_CTRL(NO_PAD_CTRL), 124 }; 125 126 #ifdef CONFIG_MXC_SPI 127 static iomux_v3_cfg_t ecspi1_pads[] = { 128 MX6_PAD_ECSPI1_MISO__ECSPI_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), 129 MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), 130 MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), 131 MX6_PAD_ECSPI1_SS0__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), 132 }; 133 134 int board_spi_cs_gpio(unsigned bus, unsigned cs) 135 { 136 return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 11)) : -1; 137 } 138 139 static void setup_spi(void) 140 { 141 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); 142 } 143 #endif 144 145 static void setup_iomux_uart(void) 146 { 147 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); 148 } 149 150 static void setup_iomux_fec(void) 151 { 152 imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); 153 154 /* Power up LAN8720 PHY */ 155 gpio_request(ETH_PHY_POWER, "eth_pwr"); 156 gpio_direction_output(ETH_PHY_POWER , 1); 157 udelay(15000); 158 } 159 160 int board_mmc_get_env_dev(int devno) 161 { 162 return devno; 163 } 164 165 #ifdef CONFIG_DM_PMIC_PFUZE100 166 int power_init_board(void) 167 { 168 struct udevice *dev; 169 int ret; 170 u32 dev_id, rev_id, i; 171 u32 switch_num = 6; 172 u32 offset = PFUZE100_SW1CMODE; 173 174 ret = pmic_get("pfuze100", &dev); 175 if (ret == -ENODEV) 176 return 0; 177 178 if (ret != 0) 179 return ret; 180 181 dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID); 182 rev_id = pmic_reg_read(dev, PFUZE100_REVID); 183 printf("PMIC: PFUZE100! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id); 184 185 /* set SW1AB staby volatage 0.975V */ 186 pmic_clrsetbits(dev, PFUZE100_SW1ABSTBY, 0x3f, 0x1b); 187 188 /* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ 189 pmic_clrsetbits(dev, PFUZE100_SW1ABCONF, 0xc0, 0x40); 190 191 /* set SW1C staby volatage 0.975V */ 192 pmic_clrsetbits(dev, PFUZE100_SW1CSTBY, 0x3f, 0x1b); 193 194 /* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */ 195 pmic_clrsetbits(dev, PFUZE100_SW1CCONF, 0xc0, 0x40); 196 197 /* Init mode to APS_PFM */ 198 pmic_reg_write(dev, PFUZE100_SW1ABMODE, APS_PFM); 199 200 for (i = 0; i < switch_num - 1; i++) 201 pmic_reg_write(dev, offset + i * SWITCH_SIZE, APS_PFM); 202 203 return 0; 204 } 205 #endif 206 207 #ifdef CONFIG_FEC_MXC 208 int board_eth_init(bd_t *bis) 209 { 210 setup_iomux_fec(); 211 212 return cpu_eth_init(bis); 213 } 214 215 static int setup_fec(void) 216 { 217 struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 218 219 /* clear gpr1[14], gpr1[18:17] to select anatop clock */ 220 clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0); 221 222 return enable_fec_anatop_clock(0, ENET_50MHZ); 223 } 224 #endif 225 226 #ifdef CONFIG_USB_EHCI_MX6 227 #define USB_OTHERREGS_OFFSET 0x800 228 #define UCTRL_PWR_POL (1 << 9) 229 230 static iomux_v3_cfg_t const usb_otg_pads[] = { 231 /* OTG1 */ 232 MX6_PAD_KEY_COL4__USB_USBOTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), 233 MX6_PAD_EPDC_PWRCOM__ANATOP_USBOTG1_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL), 234 /* OTG2 */ 235 MX6_PAD_KEY_COL5__USB_USBOTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL) 236 }; 237 238 static void setup_usb(void) 239 { 240 imx_iomux_v3_setup_multiple_pads(usb_otg_pads, 241 ARRAY_SIZE(usb_otg_pads)); 242 } 243 244 int board_usb_phy_mode(int port) 245 { 246 if (port == 1) 247 return USB_INIT_HOST; 248 else 249 return usb_phy_mode(port); 250 } 251 252 int board_ehci_hcd_init(int port) 253 { 254 u32 *usbnc_usb_ctrl; 255 256 if (port > 1) 257 return -EINVAL; 258 259 usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET + 260 port * 4); 261 262 /* Set Power polarity */ 263 setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL); 264 265 return 0; 266 } 267 #endif 268 269 int board_early_init_f(void) 270 { 271 setup_iomux_uart(); 272 273 return 0; 274 } 275 276 int board_init(void) 277 { 278 /* address of boot parameters */ 279 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 280 281 #ifdef CONFIG_MXC_SPI 282 gpio_request(IMX_GPIO_NR(4, 11), "spi_cs"); 283 setup_spi(); 284 #endif 285 286 #ifdef CONFIG_FEC_MXC 287 setup_fec(); 288 #endif 289 290 #ifdef CONFIG_USB_EHCI_MX6 291 setup_usb(); 292 #endif 293 294 return 0; 295 } 296 297 int checkboard(void) 298 { 299 puts("Board: MX6SLEVK\n"); 300 301 return 0; 302 } 303 304 #ifdef CONFIG_SPL_BUILD 305 #include <spl.h> 306 #include <libfdt.h> 307 308 #define USDHC1_CD_GPIO IMX_GPIO_NR(4, 7) 309 #define USDHC2_CD_GPIO IMX_GPIO_NR(5, 0) 310 #define USDHC3_CD_GPIO IMX_GPIO_NR(3, 22) 311 312 static struct fsl_esdhc_cfg usdhc_cfg[3] = { 313 {USDHC1_BASE_ADDR}, 314 {USDHC2_BASE_ADDR, 0, 4}, 315 {USDHC3_BASE_ADDR, 0, 4}, 316 }; 317 318 int board_mmc_getcd(struct mmc *mmc) 319 { 320 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 321 int ret = 0; 322 323 switch (cfg->esdhc_base) { 324 case USDHC1_BASE_ADDR: 325 ret = !gpio_get_value(USDHC1_CD_GPIO); 326 break; 327 case USDHC2_BASE_ADDR: 328 ret = !gpio_get_value(USDHC2_CD_GPIO); 329 break; 330 case USDHC3_BASE_ADDR: 331 ret = !gpio_get_value(USDHC3_CD_GPIO); 332 break; 333 } 334 335 return ret; 336 } 337 338 int board_mmc_init(bd_t *bis) 339 { 340 struct src *src_regs = (struct src *)SRC_BASE_ADDR; 341 u32 val; 342 u32 port; 343 344 val = readl(&src_regs->sbmr1); 345 346 /* Boot from USDHC */ 347 port = (val >> 11) & 0x3; 348 switch (port) { 349 case 0: 350 imx_iomux_v3_setup_multiple_pads(usdhc1_pads, 351 ARRAY_SIZE(usdhc1_pads)); 352 gpio_direction_input(USDHC1_CD_GPIO); 353 usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR; 354 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 355 break; 356 case 1: 357 imx_iomux_v3_setup_multiple_pads(usdhc2_pads, 358 ARRAY_SIZE(usdhc2_pads)); 359 gpio_direction_input(USDHC2_CD_GPIO); 360 usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR; 361 usdhc_cfg[0].max_bus_width = 4; 362 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 363 break; 364 case 2: 365 imx_iomux_v3_setup_multiple_pads(usdhc3_pads, 366 ARRAY_SIZE(usdhc3_pads)); 367 gpio_direction_input(USDHC3_CD_GPIO); 368 usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR; 369 usdhc_cfg[0].max_bus_width = 4; 370 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 371 break; 372 } 373 374 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; 375 return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); 376 } 377 378 const struct mx6sl_iomux_ddr_regs mx6_ddr_ioregs = { 379 .dram_sdqs0 = 0x00003030, 380 .dram_sdqs1 = 0x00003030, 381 .dram_sdqs2 = 0x00003030, 382 .dram_sdqs3 = 0x00003030, 383 .dram_dqm0 = 0x00000030, 384 .dram_dqm1 = 0x00000030, 385 .dram_dqm2 = 0x00000030, 386 .dram_dqm3 = 0x00000030, 387 .dram_cas = 0x00000030, 388 .dram_ras = 0x00000030, 389 .dram_sdclk_0 = 0x00000028, 390 .dram_reset = 0x00000030, 391 .dram_sdba2 = 0x00000000, 392 .dram_odt0 = 0x00000008, 393 .dram_odt1 = 0x00000008, 394 }; 395 396 const struct mx6sl_iomux_grp_regs mx6_grp_ioregs = { 397 .grp_b0ds = 0x00000030, 398 .grp_b1ds = 0x00000030, 399 .grp_b2ds = 0x00000030, 400 .grp_b3ds = 0x00000030, 401 .grp_addds = 0x00000030, 402 .grp_ctlds = 0x00000030, 403 .grp_ddrmode_ctl = 0x00020000, 404 .grp_ddrpke = 0x00000000, 405 .grp_ddrmode = 0x00020000, 406 .grp_ddr_type = 0x00080000, 407 }; 408 409 const struct mx6_mmdc_calibration mx6_mmcd_calib = { 410 .p0_mpdgctrl0 = 0x20000000, 411 .p0_mpdgctrl1 = 0x00000000, 412 .p0_mprddlctl = 0x4241444a, 413 .p0_mpwrdlctl = 0x3030312b, 414 .mpzqlp2ctl = 0x1b4700c7, 415 }; 416 417 static struct mx6_lpddr2_cfg mem_ddr = { 418 .mem_speed = 800, 419 .density = 4, 420 .width = 32, 421 .banks = 8, 422 .rowaddr = 14, 423 .coladdr = 10, 424 .trcd_lp = 2000, 425 .trppb_lp = 2000, 426 .trpab_lp = 2250, 427 .trasmin = 4200, 428 }; 429 430 static void ccgr_init(void) 431 { 432 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 433 434 writel(0xFFFFFFFF, &ccm->CCGR0); 435 writel(0xFFFFFFFF, &ccm->CCGR1); 436 writel(0xFFFFFFFF, &ccm->CCGR2); 437 writel(0xFFFFFFFF, &ccm->CCGR3); 438 writel(0xFFFFFFFF, &ccm->CCGR4); 439 writel(0xFFFFFFFF, &ccm->CCGR5); 440 writel(0xFFFFFFFF, &ccm->CCGR6); 441 442 writel(0x00260324, &ccm->cbcmr); 443 } 444 445 static void spl_dram_init(void) 446 { 447 struct mx6_ddr_sysinfo sysinfo = { 448 .dsize = mem_ddr.width / 32, 449 .cs_density = 20, 450 .ncs = 2, 451 .cs1_mirror = 0, 452 .walat = 0, 453 .ralat = 2, 454 .mif3_mode = 3, 455 .bi_on = 1, 456 .rtt_wr = 0, /* LPDDR2 does not need rtt_wr rtt_nom */ 457 .rtt_nom = 0, 458 .sde_to_rst = 0, /* LPDDR2 does not need this field */ 459 .rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */ 460 .ddr_type = DDR_TYPE_LPDDR2, 461 .refsel = 0, /* Refresh cycles at 64KHz */ 462 .refr = 3, /* 4 refresh commands per refresh cycle */ 463 }; 464 mx6sl_dram_iocfg(32, &mx6_ddr_ioregs, &mx6_grp_ioregs); 465 mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr); 466 } 467 468 void board_init_f(ulong dummy) 469 { 470 /* setup AIPS and disable watchdog */ 471 arch_cpu_init(); 472 473 ccgr_init(); 474 475 /* iomux and setup of i2c */ 476 board_early_init_f(); 477 478 /* setup GP timer */ 479 timer_init(); 480 481 /* UART clocks enabled and gd valid - init serial console */ 482 preloader_console_init(); 483 484 /* DDR initialization */ 485 spl_dram_init(); 486 487 /* Clear the BSS. */ 488 memset(__bss_start, 0, __bss_end - __bss_start); 489 490 /* load/boot image from boot device */ 491 board_init_r(NULL, 0); 492 } 493 #endif 494