1 /* 2 * Copyright (C) 2013 Freescale Semiconductor, Inc. 3 * 4 * Author: Fabio Estevam <fabio.estevam@freescale.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <asm/arch/clock.h> 10 #include <asm/arch/iomux.h> 11 #include <asm/arch/crm_regs.h> 12 #include <asm/arch/imx-regs.h> 13 #include <asm/arch/mx6-ddr.h> 14 #include <asm/arch/mx6-pins.h> 15 #include <asm/arch/sys_proto.h> 16 #include <asm/gpio.h> 17 #include <asm/imx-common/iomux-v3.h> 18 #include <asm/imx-common/mxc_i2c.h> 19 #include <asm/imx-common/spi.h> 20 #include <asm/io.h> 21 #include <linux/sizes.h> 22 #include <common.h> 23 #include <fsl_esdhc.h> 24 #include <i2c.h> 25 #include <mmc.h> 26 #include <netdev.h> 27 #include <power/pmic.h> 28 #include <power/pfuze100_pmic.h> 29 #include "../common/pfuze.h" 30 #include <usb.h> 31 #include <usb/ehci-fsl.h> 32 33 DECLARE_GLOBAL_DATA_PTR; 34 35 #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 36 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 37 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 38 39 #define USDHC_PAD_CTRL (PAD_CTL_PUS_22K_UP | \ 40 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ 41 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 42 43 #define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 44 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 45 PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 46 47 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ 48 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 49 50 #define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 51 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 52 PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 53 PAD_CTL_ODE | PAD_CTL_SRE_FAST) 54 55 #define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 56 PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\ 57 PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \ 58 PAD_CTL_SRE_FAST) 59 60 #define ETH_PHY_POWER IMX_GPIO_NR(4, 21) 61 62 int dram_init(void) 63 { 64 gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); 65 66 return 0; 67 } 68 69 static iomux_v3_cfg_t const uart1_pads[] = { 70 MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL), 71 MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL), 72 }; 73 74 static iomux_v3_cfg_t const usdhc1_pads[] = { 75 /* 8 bit SD */ 76 MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 77 MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 78 MX6_PAD_SD1_DAT0__USDHC1_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 79 MX6_PAD_SD1_DAT1__USDHC1_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 80 MX6_PAD_SD1_DAT2__USDHC1_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 81 MX6_PAD_SD1_DAT3__USDHC1_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 82 MX6_PAD_SD1_DAT4__USDHC1_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 83 MX6_PAD_SD1_DAT5__USDHC1_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 84 MX6_PAD_SD1_DAT6__USDHC1_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 85 MX6_PAD_SD1_DAT7__USDHC1_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 86 87 /*CD pin*/ 88 MX6_PAD_KEY_ROW7__GPIO_4_7 | MUX_PAD_CTRL(NO_PAD_CTRL), 89 }; 90 91 static iomux_v3_cfg_t const usdhc2_pads[] = { 92 MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 93 MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 94 MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 95 MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 96 MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 97 MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 98 99 /*CD pin*/ 100 MX6_PAD_SD2_DAT7__GPIO_5_0 | MUX_PAD_CTRL(NO_PAD_CTRL), 101 }; 102 103 static iomux_v3_cfg_t const usdhc3_pads[] = { 104 MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 105 MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 106 MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 107 MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 108 MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 109 MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 110 111 /*CD pin*/ 112 MX6_PAD_REF_CLK_32K__GPIO_3_22 | MUX_PAD_CTRL(NO_PAD_CTRL), 113 }; 114 115 static iomux_v3_cfg_t const fec_pads[] = { 116 MX6_PAD_FEC_MDC__FEC_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 117 MX6_PAD_FEC_MDIO__FEC_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 118 MX6_PAD_FEC_CRS_DV__FEC_RX_DV | MUX_PAD_CTRL(ENET_PAD_CTRL), 119 MX6_PAD_FEC_RXD0__FEC_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 120 MX6_PAD_FEC_RXD1__FEC_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 121 MX6_PAD_FEC_TX_EN__FEC_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), 122 MX6_PAD_FEC_TXD0__FEC_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 123 MX6_PAD_FEC_TXD1__FEC_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 124 MX6_PAD_FEC_REF_CLK__FEC_REF_OUT | MUX_PAD_CTRL(ENET_PAD_CTRL), 125 MX6_PAD_FEC_RX_ER__GPIO_4_19 | MUX_PAD_CTRL(NO_PAD_CTRL), 126 MX6_PAD_FEC_TX_CLK__GPIO_4_21 | MUX_PAD_CTRL(NO_PAD_CTRL), 127 }; 128 129 #ifdef CONFIG_MXC_SPI 130 static iomux_v3_cfg_t ecspi1_pads[] = { 131 MX6_PAD_ECSPI1_MISO__ECSPI_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), 132 MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), 133 MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), 134 MX6_PAD_ECSPI1_SS0__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), 135 }; 136 137 int board_spi_cs_gpio(unsigned bus, unsigned cs) 138 { 139 return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 11)) : -1; 140 } 141 142 static void setup_spi(void) 143 { 144 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); 145 } 146 #endif 147 148 static void setup_iomux_uart(void) 149 { 150 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); 151 } 152 153 static void setup_iomux_fec(void) 154 { 155 imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); 156 157 /* Power up LAN8720 PHY */ 158 gpio_direction_output(ETH_PHY_POWER , 1); 159 udelay(15000); 160 } 161 162 #define USDHC1_CD_GPIO IMX_GPIO_NR(4, 7) 163 #define USDHC2_CD_GPIO IMX_GPIO_NR(5, 0) 164 #define USDHC3_CD_GPIO IMX_GPIO_NR(3, 22) 165 166 static struct fsl_esdhc_cfg usdhc_cfg[3] = { 167 {USDHC1_BASE_ADDR}, 168 {USDHC2_BASE_ADDR, 0, 4}, 169 {USDHC3_BASE_ADDR, 0, 4}, 170 }; 171 172 int board_mmc_get_env_dev(int devno) 173 { 174 return devno; 175 } 176 177 int board_mmc_getcd(struct mmc *mmc) 178 { 179 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 180 int ret = 0; 181 182 switch (cfg->esdhc_base) { 183 case USDHC1_BASE_ADDR: 184 ret = !gpio_get_value(USDHC1_CD_GPIO); 185 break; 186 case USDHC2_BASE_ADDR: 187 ret = !gpio_get_value(USDHC2_CD_GPIO); 188 break; 189 case USDHC3_BASE_ADDR: 190 ret = !gpio_get_value(USDHC3_CD_GPIO); 191 break; 192 } 193 194 return ret; 195 } 196 197 int board_mmc_init(bd_t *bis) 198 { 199 #ifndef CONFIG_SPL_BUILD 200 int i, ret; 201 202 /* 203 * According to the board_mmc_init() the following map is done: 204 * (U-Boot device node) (Physical Port) 205 * mmc0 USDHC1 206 * mmc1 USDHC2 207 * mmc2 USDHC3 208 */ 209 for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { 210 switch (i) { 211 case 0: 212 imx_iomux_v3_setup_multiple_pads( 213 usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); 214 gpio_direction_input(USDHC1_CD_GPIO); 215 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 216 break; 217 case 1: 218 imx_iomux_v3_setup_multiple_pads( 219 usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); 220 gpio_direction_input(USDHC2_CD_GPIO); 221 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 222 break; 223 case 2: 224 imx_iomux_v3_setup_multiple_pads( 225 usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); 226 gpio_direction_input(USDHC3_CD_GPIO); 227 usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 228 break; 229 default: 230 printf("Warning: you configured more USDHC controllers" 231 "(%d) than supported by the board\n", i + 1); 232 return -EINVAL; 233 } 234 235 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); 236 if (ret) { 237 printf("Warning: failed to initialize " 238 "mmc dev %d\n", i); 239 return ret; 240 } 241 } 242 243 return 0; 244 #else 245 struct src *src_regs = (struct src *)SRC_BASE_ADDR; 246 u32 val; 247 u32 port; 248 249 val = readl(&src_regs->sbmr1); 250 251 /* Boot from USDHC */ 252 port = (val >> 11) & 0x3; 253 switch (port) { 254 case 0: 255 imx_iomux_v3_setup_multiple_pads(usdhc1_pads, 256 ARRAY_SIZE(usdhc1_pads)); 257 gpio_direction_input(USDHC1_CD_GPIO); 258 usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR; 259 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 260 break; 261 case 1: 262 imx_iomux_v3_setup_multiple_pads(usdhc2_pads, 263 ARRAY_SIZE(usdhc2_pads)); 264 gpio_direction_input(USDHC2_CD_GPIO); 265 usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR; 266 usdhc_cfg[0].max_bus_width = 4; 267 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 268 break; 269 case 2: 270 imx_iomux_v3_setup_multiple_pads(usdhc3_pads, 271 ARRAY_SIZE(usdhc3_pads)); 272 gpio_direction_input(USDHC3_CD_GPIO); 273 usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR; 274 usdhc_cfg[0].max_bus_width = 4; 275 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 276 break; 277 } 278 279 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; 280 return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); 281 #endif 282 } 283 284 #ifdef CONFIG_SYS_I2C_MXC 285 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) 286 /* I2C1 for PMIC */ 287 struct i2c_pads_info i2c_pad_info1 = { 288 .sda = { 289 .i2c_mode = MX6_PAD_I2C1_SDA__I2C1_SDA | PC, 290 .gpio_mode = MX6_PAD_I2C1_SDA__GPIO_3_13 | PC, 291 .gp = IMX_GPIO_NR(3, 13), 292 }, 293 .scl = { 294 .i2c_mode = MX6_PAD_I2C1_SCL__I2C1_SCL | PC, 295 .gpio_mode = MX6_PAD_I2C1_SCL__GPIO_3_12 | PC, 296 .gp = IMX_GPIO_NR(3, 12), 297 }, 298 }; 299 300 int power_init_board(void) 301 { 302 struct pmic *p; 303 304 p = pfuze_common_init(I2C_PMIC); 305 if (!p) 306 return -ENODEV; 307 308 return pfuze_mode_init(p, APS_PFM); 309 } 310 #endif 311 312 #ifdef CONFIG_FEC_MXC 313 int board_eth_init(bd_t *bis) 314 { 315 setup_iomux_fec(); 316 317 return cpu_eth_init(bis); 318 } 319 320 static int setup_fec(void) 321 { 322 struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 323 324 /* clear gpr1[14], gpr1[18:17] to select anatop clock */ 325 clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0); 326 327 return enable_fec_anatop_clock(0, ENET_50MHZ); 328 } 329 #endif 330 331 #ifdef CONFIG_USB_EHCI_MX6 332 #define USB_OTHERREGS_OFFSET 0x800 333 #define UCTRL_PWR_POL (1 << 9) 334 335 static iomux_v3_cfg_t const usb_otg_pads[] = { 336 /* OTG1 */ 337 MX6_PAD_KEY_COL4__USB_USBOTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), 338 MX6_PAD_EPDC_PWRCOM__ANATOP_USBOTG1_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL), 339 /* OTG2 */ 340 MX6_PAD_KEY_COL5__USB_USBOTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL) 341 }; 342 343 static void setup_usb(void) 344 { 345 imx_iomux_v3_setup_multiple_pads(usb_otg_pads, 346 ARRAY_SIZE(usb_otg_pads)); 347 } 348 349 int board_usb_phy_mode(int port) 350 { 351 if (port == 1) 352 return USB_INIT_HOST; 353 else 354 return usb_phy_mode(port); 355 } 356 357 int board_ehci_hcd_init(int port) 358 { 359 u32 *usbnc_usb_ctrl; 360 361 if (port > 1) 362 return -EINVAL; 363 364 usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET + 365 port * 4); 366 367 /* Set Power polarity */ 368 setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL); 369 370 return 0; 371 } 372 #endif 373 374 int board_early_init_f(void) 375 { 376 setup_iomux_uart(); 377 #ifdef CONFIG_MXC_SPI 378 setup_spi(); 379 #endif 380 return 0; 381 } 382 383 int board_init(void) 384 { 385 /* address of boot parameters */ 386 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 387 388 #ifdef CONFIG_SYS_I2C_MXC 389 setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); 390 #endif 391 392 #ifdef CONFIG_FEC_MXC 393 setup_fec(); 394 #endif 395 396 #ifdef CONFIG_USB_EHCI_MX6 397 setup_usb(); 398 #endif 399 400 return 0; 401 } 402 403 int checkboard(void) 404 { 405 puts("Board: MX6SLEVK\n"); 406 407 return 0; 408 } 409 410 #ifdef CONFIG_SPL_BUILD 411 #include <spl.h> 412 #include <libfdt.h> 413 414 const struct mx6sl_iomux_ddr_regs mx6_ddr_ioregs = { 415 .dram_sdqs0 = 0x00003030, 416 .dram_sdqs1 = 0x00003030, 417 .dram_sdqs2 = 0x00003030, 418 .dram_sdqs3 = 0x00003030, 419 .dram_dqm0 = 0x00000030, 420 .dram_dqm1 = 0x00000030, 421 .dram_dqm2 = 0x00000030, 422 .dram_dqm3 = 0x00000030, 423 .dram_cas = 0x00000030, 424 .dram_ras = 0x00000030, 425 .dram_sdclk_0 = 0x00000028, 426 .dram_reset = 0x00000030, 427 .dram_sdba2 = 0x00000000, 428 .dram_odt0 = 0x00000008, 429 .dram_odt1 = 0x00000008, 430 }; 431 432 const struct mx6sl_iomux_grp_regs mx6_grp_ioregs = { 433 .grp_b0ds = 0x00000030, 434 .grp_b1ds = 0x00000030, 435 .grp_b2ds = 0x00000030, 436 .grp_b3ds = 0x00000030, 437 .grp_addds = 0x00000030, 438 .grp_ctlds = 0x00000030, 439 .grp_ddrmode_ctl = 0x00020000, 440 .grp_ddrpke = 0x00000000, 441 .grp_ddrmode = 0x00020000, 442 .grp_ddr_type = 0x00080000, 443 }; 444 445 const struct mx6_mmdc_calibration mx6_mmcd_calib = { 446 .p0_mpdgctrl0 = 0x20000000, 447 .p0_mpdgctrl1 = 0x00000000, 448 .p0_mprddlctl = 0x4241444a, 449 .p0_mpwrdlctl = 0x3030312b, 450 .mpzqlp2ctl = 0x1b4700c7, 451 }; 452 453 static struct mx6_lpddr2_cfg mem_ddr = { 454 .mem_speed = 800, 455 .density = 4, 456 .width = 32, 457 .banks = 8, 458 .rowaddr = 14, 459 .coladdr = 10, 460 .trcd_lp = 2000, 461 .trppb_lp = 2000, 462 .trpab_lp = 2250, 463 .trasmin = 4200, 464 }; 465 466 static void ccgr_init(void) 467 { 468 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 469 470 writel(0xFFFFFFFF, &ccm->CCGR0); 471 writel(0xFFFFFFFF, &ccm->CCGR1); 472 writel(0xFFFFFFFF, &ccm->CCGR2); 473 writel(0xFFFFFFFF, &ccm->CCGR3); 474 writel(0xFFFFFFFF, &ccm->CCGR4); 475 writel(0xFFFFFFFF, &ccm->CCGR5); 476 writel(0xFFFFFFFF, &ccm->CCGR6); 477 478 writel(0x00260324, &ccm->cbcmr); 479 } 480 481 static void spl_dram_init(void) 482 { 483 struct mx6_ddr_sysinfo sysinfo = { 484 .dsize = mem_ddr.width / 32, 485 .cs_density = 20, 486 .ncs = 2, 487 .cs1_mirror = 0, 488 .walat = 0, 489 .ralat = 2, 490 .mif3_mode = 3, 491 .bi_on = 1, 492 .rtt_wr = 0, /* LPDDR2 does not need rtt_wr rtt_nom */ 493 .rtt_nom = 0, 494 .sde_to_rst = 0, /* LPDDR2 does not need this field */ 495 .rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */ 496 .ddr_type = DDR_TYPE_LPDDR2, 497 }; 498 mx6sl_dram_iocfg(32, &mx6_ddr_ioregs, &mx6_grp_ioregs); 499 mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr); 500 } 501 502 void board_init_f(ulong dummy) 503 { 504 /* setup AIPS and disable watchdog */ 505 arch_cpu_init(); 506 507 ccgr_init(); 508 509 /* iomux and setup of i2c */ 510 board_early_init_f(); 511 512 /* setup GP timer */ 513 timer_init(); 514 515 /* UART clocks enabled and gd valid - init serial console */ 516 preloader_console_init(); 517 518 /* DDR initialization */ 519 spl_dram_init(); 520 521 /* Clear the BSS. */ 522 memset(__bss_start, 0, __bss_end - __bss_start); 523 524 /* load/boot image from boot device */ 525 board_init_r(NULL, 0); 526 } 527 #endif 528