1 /*
2  * Copyright (C) 2013 Freescale Semiconductor, Inc.
3  *
4  * Author: Fabio Estevam <fabio.estevam@freescale.com>
5  *
6  * SPDX-License-Identifier:	GPL-2.0+
7  */
8 
9 #include <asm/arch/clock.h>
10 #include <asm/arch/iomux.h>
11 #include <asm/arch/imx-regs.h>
12 #include <asm/arch/mx6-pins.h>
13 #include <asm/arch/sys_proto.h>
14 #include <asm/gpio.h>
15 #include <asm/imx-common/iomux-v3.h>
16 #include <asm/io.h>
17 #include <linux/sizes.h>
18 #include <common.h>
19 #include <fsl_esdhc.h>
20 #include <mmc.h>
21 #include <netdev.h>
22 
23 DECLARE_GLOBAL_DATA_PTR;
24 
25 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
26 	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
27 	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
28 
29 #define USDHC_PAD_CTRL (PAD_CTL_PUS_22K_UP |			\
30 	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
31 	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
32 
33 #define ENET_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
34 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED   |             \
35 	PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
36 
37 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
38 		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
39 
40 #define ETH_PHY_RESET	IMX_GPIO_NR(4, 21)
41 
42 int dram_init(void)
43 {
44 	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
45 
46 	return 0;
47 }
48 
49 static iomux_v3_cfg_t const uart1_pads[] = {
50 	MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
51 	MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
52 };
53 
54 static iomux_v3_cfg_t const usdhc2_pads[] = {
55 	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
56 	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
57 	MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
58 	MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
59 	MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
60 	MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
61 };
62 
63 static iomux_v3_cfg_t const fec_pads[] = {
64 	MX6_PAD_FEC_MDC__FEC_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
65 	MX6_PAD_FEC_MDIO__FEC_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
66 	MX6_PAD_FEC_CRS_DV__FEC_RX_DV | MUX_PAD_CTRL(ENET_PAD_CTRL),
67 	MX6_PAD_FEC_RXD0__FEC_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
68 	MX6_PAD_FEC_RXD1__FEC_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
69 	MX6_PAD_FEC_TX_EN__FEC_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
70 	MX6_PAD_FEC_TXD0__FEC_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
71 	MX6_PAD_FEC_TXD1__FEC_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
72 	MX6_PAD_FEC_REF_CLK__FEC_REF_OUT | MUX_PAD_CTRL(ENET_PAD_CTRL),
73 	MX6_PAD_FEC_RX_ER__GPIO_4_19 | MUX_PAD_CTRL(NO_PAD_CTRL),
74 	MX6_PAD_FEC_TX_CLK__GPIO_4_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
75 };
76 
77 #ifdef CONFIG_MXC_SPI
78 static iomux_v3_cfg_t ecspi1_pads[] = {
79 	MX6_PAD_ECSPI1_MISO__ECSPI_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
80 	MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
81 	MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
82 	MX6_PAD_ECSPI1_SS0__GPIO4_IO11  | MUX_PAD_CTRL(NO_PAD_CTRL),
83 };
84 
85 int board_spi_cs_gpio(unsigned bus, unsigned cs)
86 {
87 	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 11)) : -1;
88 }
89 
90 static void setup_spi(void)
91 {
92 	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
93 }
94 #endif
95 
96 static void setup_iomux_uart(void)
97 {
98 	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
99 }
100 
101 static void setup_iomux_fec(void)
102 {
103 	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
104 
105 	/* Reset LAN8720 PHY */
106 	gpio_direction_output(ETH_PHY_RESET , 0);
107 	udelay(1000);
108 	gpio_set_value(ETH_PHY_RESET, 1);
109 }
110 
111 static struct fsl_esdhc_cfg usdhc_cfg[1] = {
112 	{USDHC2_BASE_ADDR},
113 };
114 
115 int board_mmc_getcd(struct mmc *mmc)
116 {
117 	return 1;	/* Assume boot SD always present */
118 }
119 
120 int board_mmc_init(bd_t *bis)
121 {
122 	imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
123 
124 	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
125 	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
126 }
127 
128 #ifdef CONFIG_FEC_MXC
129 int board_eth_init(bd_t *bis)
130 {
131 	setup_iomux_fec();
132 
133 	return cpu_eth_init(bis);
134 }
135 
136 static int setup_fec(void)
137 {
138 	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
139 	int ret;
140 
141 	/* clear gpr1[14], gpr1[18:17] to select anatop clock */
142 	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0);
143 
144 	ret = enable_fec_anatop_clock(ENET_50MHz);
145 	if (ret)
146 		return ret;
147 
148 	return 0;
149 }
150 #endif
151 
152 
153 int board_early_init_f(void)
154 {
155 	setup_iomux_uart();
156 #ifdef CONFIG_MXC_SPI
157 	setup_spi();
158 #endif
159 	return 0;
160 }
161 
162 int board_init(void)
163 {
164 	/* address of boot parameters */
165 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
166 
167 #ifdef	CONFIG_FEC_MXC
168 	setup_fec();
169 #endif
170 	return 0;
171 }
172 
173 u32 get_board_rev(void)
174 {
175 	return get_cpu_rev();
176 }
177 
178 int checkboard(void)
179 {
180 	puts("Board: MX6SLEVK\n");
181 
182 	return 0;
183 }
184