1 /*
2  * Copyright (C) 2011 Freescale Semiconductor, Inc.
3  * Jason Liu <r64343@freescale.com>
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 #include <common.h>
9 #include <asm/io.h>
10 #include <asm/arch/imx-regs.h>
11 #include <asm/arch/sys_proto.h>
12 #include <asm/arch/crm_regs.h>
13 #include <asm/arch/clock.h>
14 #include <asm/arch/iomux-mx53.h>
15 #include <asm/arch/clock.h>
16 #include <asm/errno.h>
17 #include <asm/imx-common/mx5_video.h>
18 #include <netdev.h>
19 #include <i2c.h>
20 #include <mmc.h>
21 #include <fsl_esdhc.h>
22 #include <asm/gpio.h>
23 #include <power/pmic.h>
24 #include <dialog_pmic.h>
25 #include <fsl_pmic.h>
26 #include <linux/fb.h>
27 #include <ipu_pixfmt.h>
28 
29 #define MX53LOCO_LCD_POWER		IMX_GPIO_NR(3, 24)
30 
31 DECLARE_GLOBAL_DATA_PTR;
32 
33 int dram_init(void)
34 {
35 	u32 size1, size2;
36 
37 	size1 = get_ram_size((void *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
38 	size2 = get_ram_size((void *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE);
39 
40 	gd->ram_size = size1 + size2;
41 
42 	return 0;
43 }
44 void dram_init_banksize(void)
45 {
46 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
47 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
48 
49 	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
50 	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
51 }
52 
53 u32 get_board_rev(void)
54 {
55 	struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
56 	struct fuse_bank *bank = &iim->bank[0];
57 	struct fuse_bank0_regs *fuse =
58 		(struct fuse_bank0_regs *)bank->fuse_regs;
59 
60 	int rev = readl(&fuse->gp[6]);
61 
62 	if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR))
63 		rev = 0;
64 
65 	return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
66 }
67 
68 #define UART_PAD_CTRL	(PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
69 			 PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
70 
71 static void setup_iomux_uart(void)
72 {
73 	static const iomux_v3_cfg_t uart_pads[] = {
74 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__UART1_RXD_MUX, UART_PAD_CTRL),
75 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__UART1_TXD_MUX, UART_PAD_CTRL),
76 	};
77 
78 	imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
79 }
80 
81 #ifdef CONFIG_USB_EHCI_MX5
82 int board_ehci_hcd_init(int port)
83 {
84 	/* request VBUS power enable pin, GPIO7_8 */
85 	imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8);
86 	gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
87 	return 0;
88 }
89 #endif
90 
91 static void setup_iomux_fec(void)
92 {
93 	static const iomux_v3_cfg_t fec_pads[] = {
94 		NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
95 			PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
96 		NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
97 		NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
98 				PAD_CTL_HYS | PAD_CTL_PKE),
99 		NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
100 				PAD_CTL_HYS | PAD_CTL_PKE),
101 		NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
102 		NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
103 		NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
104 		NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
105 				PAD_CTL_HYS | PAD_CTL_PKE),
106 		NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
107 				PAD_CTL_HYS | PAD_CTL_PKE),
108 		NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
109 				PAD_CTL_HYS | PAD_CTL_PKE),
110 	};
111 
112 	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
113 }
114 
115 #ifdef CONFIG_FSL_ESDHC
116 struct fsl_esdhc_cfg esdhc_cfg[2] = {
117 	{MMC_SDHC1_BASE_ADDR},
118 	{MMC_SDHC3_BASE_ADDR},
119 };
120 
121 int board_mmc_getcd(struct mmc *mmc)
122 {
123 	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
124 	int ret;
125 
126 	imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA11__GPIO3_11);
127 	gpio_direction_input(IMX_GPIO_NR(3, 11));
128 	imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA13__GPIO3_13);
129 	gpio_direction_input(IMX_GPIO_NR(3, 13));
130 
131 	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
132 		ret = !gpio_get_value(IMX_GPIO_NR(3, 13));
133 	else
134 		ret = !gpio_get_value(IMX_GPIO_NR(3, 11));
135 
136 	return ret;
137 }
138 
139 #define SD_CMD_PAD_CTRL		(PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
140 				 PAD_CTL_PUS_100K_UP)
141 #define SD_PAD_CTRL		(PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
142 				 PAD_CTL_DSE_HIGH)
143 
144 int board_mmc_init(bd_t *bis)
145 {
146 	static const iomux_v3_cfg_t sd1_pads[] = {
147 		NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
148 		NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
149 		NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
150 		NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
151 		NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
152 		NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
153 		MX53_PAD_EIM_DA13__GPIO3_13,
154 	};
155 
156 	static const iomux_v3_cfg_t sd2_pads[] = {
157 		NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
158 				SD_CMD_PAD_CTRL),
159 		NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
160 		NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
161 		NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
162 		NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
163 		NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
164 		NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
165 		NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
166 		NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
167 		NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
168 		MX53_PAD_EIM_DA11__GPIO3_11,
169 	};
170 
171 	u32 index;
172 	s32 status = 0;
173 
174 	esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
175 	esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
176 
177 	for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
178 		switch (index) {
179 		case 0:
180 			imx_iomux_v3_setup_multiple_pads(sd1_pads,
181 							 ARRAY_SIZE(sd1_pads));
182 			break;
183 		case 1:
184 			imx_iomux_v3_setup_multiple_pads(sd2_pads,
185 							 ARRAY_SIZE(sd2_pads));
186 			break;
187 		default:
188 			printf("Warning: you configured more ESDHC controller"
189 				"(%d) as supported by the board(2)\n",
190 				CONFIG_SYS_FSL_ESDHC_NUM);
191 			return status;
192 		}
193 		status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
194 	}
195 
196 	return status;
197 }
198 #endif
199 
200 #define I2C_PAD_CTRL	(PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
201 			 PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
202 
203 static void setup_iomux_i2c(void)
204 {
205 	static const iomux_v3_cfg_t i2c1_pads[] = {
206 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL),
207 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL),
208 	};
209 
210 	imx_iomux_v3_setup_multiple_pads(i2c1_pads, ARRAY_SIZE(i2c1_pads));
211 }
212 
213 static int power_init(void)
214 {
215 	unsigned int val;
216 	int ret;
217 	struct pmic *p;
218 
219 	if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR)) {
220 		ret = pmic_dialog_init(I2C_PMIC);
221 		if (ret)
222 			return ret;
223 
224 		p = pmic_get("DIALOG_PMIC");
225 		if (!p)
226 			return -ENODEV;
227 
228 		/* Set VDDA to 1.25V */
229 		val = DA9052_BUCKCORE_BCOREEN | DA_BUCKCORE_VBCORE_1_250V;
230 		ret = pmic_reg_write(p, DA9053_BUCKCORE_REG, val);
231 		if (ret) {
232 			printf("Writing to BUCKCORE_REG failed: %d\n", ret);
233 			return ret;
234 		}
235 
236 		pmic_reg_read(p, DA9053_SUPPLY_REG, &val);
237 		val |= DA9052_SUPPLY_VBCOREGO;
238 		ret = pmic_reg_write(p, DA9053_SUPPLY_REG, val);
239 		if (ret) {
240 			printf("Writing to SUPPLY_REG failed: %d\n", ret);
241 			return ret;
242 		}
243 
244 		/* Set Vcc peripheral to 1.30V */
245 		ret = pmic_reg_write(p, DA9053_BUCKPRO_REG, 0x62);
246 		if (ret) {
247 			printf("Writing to BUCKPRO_REG failed: %d\n", ret);
248 			return ret;
249 		}
250 
251 		ret = pmic_reg_write(p, DA9053_SUPPLY_REG, 0x62);
252 		if (ret) {
253 			printf("Writing to SUPPLY_REG failed: %d\n", ret);
254 			return ret;
255 		}
256 
257 		return ret;
258 	}
259 
260 	if (!i2c_probe(CONFIG_SYS_FSL_PMIC_I2C_ADDR)) {
261 		ret = pmic_init(I2C_PMIC);
262 		if (ret)
263 			return ret;
264 
265 		p = pmic_get("FSL_PMIC");
266 		if (!p)
267 			return -ENODEV;
268 
269 		/* Set VDDGP to 1.25V for 1GHz on SW1 */
270 		pmic_reg_read(p, REG_SW_0, &val);
271 		val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_250V_MC34708;
272 		ret = pmic_reg_write(p, REG_SW_0, val);
273 		if (ret) {
274 			printf("Writing to REG_SW_0 failed: %d\n", ret);
275 			return ret;
276 		}
277 
278 		/* Set VCC as 1.30V on SW2 */
279 		pmic_reg_read(p, REG_SW_1, &val);
280 		val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_300V_MC34708;
281 		ret = pmic_reg_write(p, REG_SW_1, val);
282 		if (ret) {
283 			printf("Writing to REG_SW_1 failed: %d\n", ret);
284 			return ret;
285 		}
286 
287 		/* Set global reset timer to 4s */
288 		pmic_reg_read(p, REG_POWER_CTL2, &val);
289 		val = (val & ~TIMER_MASK_MC34708) | TIMER_4S_MC34708;
290 		ret = pmic_reg_write(p, REG_POWER_CTL2, val);
291 		if (ret) {
292 			printf("Writing to REG_POWER_CTL2 failed: %d\n", ret);
293 			return ret;
294 		}
295 
296 		/* Set VUSBSEL and VUSBEN for USB PHY supply*/
297 		pmic_reg_read(p, REG_MODE_0, &val);
298 		val |= (VUSBSEL_MC34708 | VUSBEN_MC34708);
299 		ret = pmic_reg_write(p, REG_MODE_0, val);
300 		if (ret) {
301 			printf("Writing to REG_MODE_0 failed: %d\n", ret);
302 			return ret;
303 		}
304 
305 		/* Set SWBST to 5V in auto mode */
306 		val = SWBST_AUTO;
307 		ret = pmic_reg_write(p, SWBST_CTRL, val);
308 		if (ret) {
309 			printf("Writing to SWBST_CTRL failed: %d\n", ret);
310 			return ret;
311 		}
312 
313 		return ret;
314 	}
315 
316 	return -1;
317 }
318 
319 static void clock_1GHz(void)
320 {
321 	int ret;
322 	u32 ref_clk = MXC_HCLK;
323 	/*
324 	 * After increasing voltage to 1.25V, we can switch
325 	 * CPU clock to 1GHz and DDR to 400MHz safely
326 	 */
327 	ret = mxc_set_clock(ref_clk, 1000, MXC_ARM_CLK);
328 	if (ret)
329 		printf("CPU:   Switch CPU clock to 1GHZ failed\n");
330 
331 	ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK);
332 	ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK);
333 	if (ret)
334 		printf("CPU:   Switch DDR clock to 400MHz failed\n");
335 }
336 
337 int board_early_init_f(void)
338 {
339 	setup_iomux_uart();
340 	setup_iomux_fec();
341 	setup_iomux_lcd();
342 
343 	return 0;
344 }
345 
346 int print_cpuinfo(void)
347 {
348 	u32 cpurev;
349 
350 	cpurev = get_cpu_rev();
351 	printf("CPU:   Freescale i.MX%x family rev%d.%d at %d MHz\n",
352 		(cpurev & 0xFF000) >> 12,
353 		(cpurev & 0x000F0) >> 4,
354 		(cpurev & 0x0000F) >> 0,
355 		mxc_get_clock(MXC_ARM_CLK) / 1000000);
356 	printf("Reset cause: %s\n", get_reset_cause());
357 	return 0;
358 }
359 
360 /*
361  * Do not overwrite the console
362  * Use always serial for U-Boot console
363  */
364 int overwrite_console(void)
365 {
366 	return 1;
367 }
368 
369 int board_init(void)
370 {
371 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
372 
373 	mxc_set_sata_internal_clock();
374 	setup_iomux_i2c();
375 
376 	return 0;
377 }
378 
379 int board_late_init(void)
380 {
381 	if (!power_init())
382 		clock_1GHz();
383 	print_cpuinfo();
384 
385 	return 0;
386 }
387 
388 int checkboard(void)
389 {
390 	puts("Board: MX53 LOCO\n");
391 
392 	return 0;
393 }
394