1 /* 2 * Copyright (C) 2011 Freescale Semiconductor, Inc. 3 * Jason Liu <r64343@freescale.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #include <common.h> 9 #include <asm/io.h> 10 #include <asm/arch/imx-regs.h> 11 #include <asm/arch/sys_proto.h> 12 #include <asm/arch/crm_regs.h> 13 #include <asm/arch/clock.h> 14 #include <asm/arch/iomux-mx53.h> 15 #include <asm/arch/clock.h> 16 #include <asm/errno.h> 17 #include <asm/imx-common/mx5_video.h> 18 #include <netdev.h> 19 #include <i2c.h> 20 #include <mmc.h> 21 #include <fsl_esdhc.h> 22 #include <asm/gpio.h> 23 #include <power/pmic.h> 24 #include <dialog_pmic.h> 25 #include <fsl_pmic.h> 26 #include <linux/fb.h> 27 #include <ipu_pixfmt.h> 28 29 #define MX53LOCO_LCD_POWER IMX_GPIO_NR(3, 24) 30 31 DECLARE_GLOBAL_DATA_PTR; 32 33 static uint32_t mx53_dram_size[2]; 34 35 phys_size_t get_effective_memsize(void) 36 { 37 /* 38 * WARNING: We must override get_effective_memsize() function here 39 * to report only the size of the first DRAM bank. This is to make 40 * U-Boot relocator place U-Boot into valid memory, that is, at the 41 * end of the first DRAM bank. If we did not override this function 42 * like so, U-Boot would be placed at the address of the first DRAM 43 * bank + total DRAM size - sizeof(uboot), which in the setup where 44 * each DRAM bank contains 512MiB of DRAM would result in placing 45 * U-Boot into invalid memory area close to the end of the first 46 * DRAM bank. 47 */ 48 return mx53_dram_size[0]; 49 } 50 51 int dram_init(void) 52 { 53 mx53_dram_size[0] = get_ram_size((void *)PHYS_SDRAM_1, 1 << 30); 54 mx53_dram_size[1] = get_ram_size((void *)PHYS_SDRAM_2, 1 << 30); 55 56 gd->ram_size = mx53_dram_size[0] + mx53_dram_size[1]; 57 58 return 0; 59 } 60 61 void dram_init_banksize(void) 62 { 63 gd->bd->bi_dram[0].start = PHYS_SDRAM_1; 64 gd->bd->bi_dram[0].size = mx53_dram_size[0]; 65 66 gd->bd->bi_dram[1].start = PHYS_SDRAM_2; 67 gd->bd->bi_dram[1].size = mx53_dram_size[1]; 68 } 69 70 u32 get_board_rev(void) 71 { 72 struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE; 73 struct fuse_bank *bank = &iim->bank[0]; 74 struct fuse_bank0_regs *fuse = 75 (struct fuse_bank0_regs *)bank->fuse_regs; 76 77 int rev = readl(&fuse->gp[6]); 78 79 if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR)) 80 rev = 0; 81 82 return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8; 83 } 84 85 #define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \ 86 PAD_CTL_PUS_100K_UP | PAD_CTL_ODE) 87 88 static void setup_iomux_uart(void) 89 { 90 static const iomux_v3_cfg_t uart_pads[] = { 91 NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__UART1_RXD_MUX, UART_PAD_CTRL), 92 NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__UART1_TXD_MUX, UART_PAD_CTRL), 93 }; 94 95 imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads)); 96 } 97 98 #ifdef CONFIG_USB_EHCI_MX5 99 int board_ehci_hcd_init(int port) 100 { 101 /* request VBUS power enable pin, GPIO7_8 */ 102 imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8); 103 gpio_direction_output(IMX_GPIO_NR(7, 8), 1); 104 return 0; 105 } 106 #endif 107 108 static void setup_iomux_fec(void) 109 { 110 static const iomux_v3_cfg_t fec_pads[] = { 111 NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS | 112 PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE), 113 NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH), 114 NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1, 115 PAD_CTL_HYS | PAD_CTL_PKE), 116 NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0, 117 PAD_CTL_HYS | PAD_CTL_PKE), 118 NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH), 119 NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH), 120 NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH), 121 NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK, 122 PAD_CTL_HYS | PAD_CTL_PKE), 123 NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER, 124 PAD_CTL_HYS | PAD_CTL_PKE), 125 NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV, 126 PAD_CTL_HYS | PAD_CTL_PKE), 127 }; 128 129 imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); 130 } 131 132 #ifdef CONFIG_FSL_ESDHC 133 struct fsl_esdhc_cfg esdhc_cfg[2] = { 134 {MMC_SDHC1_BASE_ADDR}, 135 {MMC_SDHC3_BASE_ADDR}, 136 }; 137 138 int board_mmc_getcd(struct mmc *mmc) 139 { 140 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 141 int ret; 142 143 imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA11__GPIO3_11); 144 gpio_direction_input(IMX_GPIO_NR(3, 11)); 145 imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA13__GPIO3_13); 146 gpio_direction_input(IMX_GPIO_NR(3, 13)); 147 148 if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR) 149 ret = !gpio_get_value(IMX_GPIO_NR(3, 13)); 150 else 151 ret = !gpio_get_value(IMX_GPIO_NR(3, 11)); 152 153 return ret; 154 } 155 156 #define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \ 157 PAD_CTL_PUS_100K_UP) 158 #define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \ 159 PAD_CTL_DSE_HIGH) 160 161 int board_mmc_init(bd_t *bis) 162 { 163 static const iomux_v3_cfg_t sd1_pads[] = { 164 NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL), 165 NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL), 166 NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL), 167 NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL), 168 NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL), 169 NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL), 170 MX53_PAD_EIM_DA13__GPIO3_13, 171 }; 172 173 static const iomux_v3_cfg_t sd2_pads[] = { 174 NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD, 175 SD_CMD_PAD_CTRL), 176 NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL), 177 NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL), 178 NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL), 179 NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL), 180 NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL), 181 NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL), 182 NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL), 183 NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL), 184 NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL), 185 MX53_PAD_EIM_DA11__GPIO3_11, 186 }; 187 188 u32 index; 189 s32 status = 0; 190 191 esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 192 esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 193 194 for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) { 195 switch (index) { 196 case 0: 197 imx_iomux_v3_setup_multiple_pads(sd1_pads, 198 ARRAY_SIZE(sd1_pads)); 199 break; 200 case 1: 201 imx_iomux_v3_setup_multiple_pads(sd2_pads, 202 ARRAY_SIZE(sd2_pads)); 203 break; 204 default: 205 printf("Warning: you configured more ESDHC controller" 206 "(%d) as supported by the board(2)\n", 207 CONFIG_SYS_FSL_ESDHC_NUM); 208 return status; 209 } 210 status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]); 211 } 212 213 return status; 214 } 215 #endif 216 217 #define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \ 218 PAD_CTL_PUS_100K_UP | PAD_CTL_ODE) 219 220 static void setup_iomux_i2c(void) 221 { 222 static const iomux_v3_cfg_t i2c1_pads[] = { 223 NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL), 224 NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL), 225 }; 226 227 imx_iomux_v3_setup_multiple_pads(i2c1_pads, ARRAY_SIZE(i2c1_pads)); 228 } 229 230 static int power_init(void) 231 { 232 unsigned int val; 233 int ret; 234 struct pmic *p; 235 236 if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR)) { 237 ret = pmic_dialog_init(I2C_PMIC); 238 if (ret) 239 return ret; 240 241 p = pmic_get("DIALOG_PMIC"); 242 if (!p) 243 return -ENODEV; 244 245 /* Set VDDA to 1.25V */ 246 val = DA9052_BUCKCORE_BCOREEN | DA_BUCKCORE_VBCORE_1_250V; 247 ret = pmic_reg_write(p, DA9053_BUCKCORE_REG, val); 248 if (ret) { 249 printf("Writing to BUCKCORE_REG failed: %d\n", ret); 250 return ret; 251 } 252 253 pmic_reg_read(p, DA9053_SUPPLY_REG, &val); 254 val |= DA9052_SUPPLY_VBCOREGO; 255 ret = pmic_reg_write(p, DA9053_SUPPLY_REG, val); 256 if (ret) { 257 printf("Writing to SUPPLY_REG failed: %d\n", ret); 258 return ret; 259 } 260 261 /* Set Vcc peripheral to 1.30V */ 262 ret = pmic_reg_write(p, DA9053_BUCKPRO_REG, 0x62); 263 if (ret) { 264 printf("Writing to BUCKPRO_REG failed: %d\n", ret); 265 return ret; 266 } 267 268 ret = pmic_reg_write(p, DA9053_SUPPLY_REG, 0x62); 269 if (ret) { 270 printf("Writing to SUPPLY_REG failed: %d\n", ret); 271 return ret; 272 } 273 274 return ret; 275 } 276 277 if (!i2c_probe(CONFIG_SYS_FSL_PMIC_I2C_ADDR)) { 278 ret = pmic_init(I2C_0); 279 if (ret) 280 return ret; 281 282 p = pmic_get("FSL_PMIC"); 283 if (!p) 284 return -ENODEV; 285 286 /* Set VDDGP to 1.25V for 1GHz on SW1 */ 287 pmic_reg_read(p, REG_SW_0, &val); 288 val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_250V_MC34708; 289 ret = pmic_reg_write(p, REG_SW_0, val); 290 if (ret) { 291 printf("Writing to REG_SW_0 failed: %d\n", ret); 292 return ret; 293 } 294 295 /* Set VCC as 1.30V on SW2 */ 296 pmic_reg_read(p, REG_SW_1, &val); 297 val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_300V_MC34708; 298 ret = pmic_reg_write(p, REG_SW_1, val); 299 if (ret) { 300 printf("Writing to REG_SW_1 failed: %d\n", ret); 301 return ret; 302 } 303 304 /* Set global reset timer to 4s */ 305 pmic_reg_read(p, REG_POWER_CTL2, &val); 306 val = (val & ~TIMER_MASK_MC34708) | TIMER_4S_MC34708; 307 ret = pmic_reg_write(p, REG_POWER_CTL2, val); 308 if (ret) { 309 printf("Writing to REG_POWER_CTL2 failed: %d\n", ret); 310 return ret; 311 } 312 313 /* Set VUSBSEL and VUSBEN for USB PHY supply*/ 314 pmic_reg_read(p, REG_MODE_0, &val); 315 val |= (VUSBSEL_MC34708 | VUSBEN_MC34708); 316 ret = pmic_reg_write(p, REG_MODE_0, val); 317 if (ret) { 318 printf("Writing to REG_MODE_0 failed: %d\n", ret); 319 return ret; 320 } 321 322 /* Set SWBST to 5V in auto mode */ 323 val = SWBST_AUTO; 324 ret = pmic_reg_write(p, SWBST_CTRL, val); 325 if (ret) { 326 printf("Writing to SWBST_CTRL failed: %d\n", ret); 327 return ret; 328 } 329 330 return ret; 331 } 332 333 return -1; 334 } 335 336 static void clock_1GHz(void) 337 { 338 int ret; 339 u32 ref_clk = MXC_HCLK; 340 /* 341 * After increasing voltage to 1.25V, we can switch 342 * CPU clock to 1GHz and DDR to 400MHz safely 343 */ 344 ret = mxc_set_clock(ref_clk, 1000, MXC_ARM_CLK); 345 if (ret) 346 printf("CPU: Switch CPU clock to 1GHZ failed\n"); 347 348 ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK); 349 ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK); 350 if (ret) 351 printf("CPU: Switch DDR clock to 400MHz failed\n"); 352 } 353 354 int board_early_init_f(void) 355 { 356 setup_iomux_uart(); 357 setup_iomux_fec(); 358 setup_iomux_lcd(); 359 360 return 0; 361 } 362 363 #if defined(CONFIG_DISPLAY_CPUINFO) 364 int print_cpuinfo(void) 365 { 366 u32 cpurev; 367 368 cpurev = get_cpu_rev(); 369 printf("CPU: Freescale i.MX%x family rev%d.%d at %d MHz\n", 370 (cpurev & 0xFF000) >> 12, 371 (cpurev & 0x000F0) >> 4, 372 (cpurev & 0x0000F) >> 0, 373 mxc_get_clock(MXC_ARM_CLK) / 1000000); 374 printf("Reset cause: %s\n", get_reset_cause()); 375 return 0; 376 } 377 #endif 378 379 /* 380 * Do not overwrite the console 381 * Use always serial for U-Boot console 382 */ 383 int overwrite_console(void) 384 { 385 return 1; 386 } 387 388 int board_init(void) 389 { 390 gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; 391 392 mxc_set_sata_internal_clock(); 393 setup_iomux_i2c(); 394 395 return 0; 396 } 397 398 int board_late_init(void) 399 { 400 if (!power_init()) 401 clock_1GHz(); 402 print_cpuinfo(); 403 404 return 0; 405 } 406 407 int checkboard(void) 408 { 409 puts("Board: MX53 LOCO\n"); 410 411 return 0; 412 } 413