1 /* 2 * (C) Copyright 2009 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <asm/io.h> 9 #include <asm/gpio.h> 10 #include <asm/arch/imx-regs.h> 11 #include <asm/arch/iomux-mx51.h> 12 #include <asm/errno.h> 13 #include <asm/arch/sys_proto.h> 14 #include <asm/arch/crm_regs.h> 15 #include <asm/arch/clock.h> 16 #include <asm/imx-common/mx5_video.h> 17 #include <i2c.h> 18 #include <mmc.h> 19 #include <fsl_esdhc.h> 20 #include <power/pmic.h> 21 #include <fsl_pmic.h> 22 #include <mc13892.h> 23 #include <usb/ehci-fsl.h> 24 25 DECLARE_GLOBAL_DATA_PTR; 26 27 #ifdef CONFIG_FSL_ESDHC 28 struct fsl_esdhc_cfg esdhc_cfg[2] = { 29 {MMC_SDHC1_BASE_ADDR}, 30 {MMC_SDHC2_BASE_ADDR}, 31 }; 32 #endif 33 34 int dram_init(void) 35 { 36 /* dram_init must store complete ramsize in gd->ram_size */ 37 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 38 PHYS_SDRAM_1_SIZE); 39 return 0; 40 } 41 42 u32 get_board_rev(void) 43 { 44 u32 rev = get_cpu_rev(); 45 if (!gpio_get_value(IMX_GPIO_NR(1, 22))) 46 rev |= BOARD_REV_2_0 << BOARD_VER_OFFSET; 47 return rev; 48 } 49 50 #define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_DSE_HIGH) 51 52 static void setup_iomux_uart(void) 53 { 54 static const iomux_v3_cfg_t uart_pads[] = { 55 MX51_PAD_UART1_RXD__UART1_RXD, 56 MX51_PAD_UART1_TXD__UART1_TXD, 57 NEW_PAD_CTRL(MX51_PAD_UART1_RTS__UART1_RTS, UART_PAD_CTRL), 58 NEW_PAD_CTRL(MX51_PAD_UART1_CTS__UART1_CTS, UART_PAD_CTRL), 59 }; 60 61 imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads)); 62 } 63 64 static void setup_iomux_fec(void) 65 { 66 static const iomux_v3_cfg_t fec_pads[] = { 67 NEW_PAD_CTRL(MX51_PAD_EIM_EB2__FEC_MDIO, PAD_CTL_HYS | 68 PAD_CTL_PUS_22K_UP | PAD_CTL_ODE | 69 PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST), 70 MX51_PAD_NANDF_CS3__FEC_MDC, 71 NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2), 72 NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2), 73 NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2), 74 MX51_PAD_NANDF_D9__FEC_RDATA0, 75 MX51_PAD_NANDF_CS6__FEC_TDATA3, 76 MX51_PAD_NANDF_CS5__FEC_TDATA2, 77 MX51_PAD_NANDF_CS4__FEC_TDATA1, 78 MX51_PAD_NANDF_D8__FEC_TDATA0, 79 MX51_PAD_NANDF_CS7__FEC_TX_EN, 80 MX51_PAD_NANDF_CS2__FEC_TX_ER, 81 MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK, 82 NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4), 83 NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4), 84 MX51_PAD_EIM_CS5__FEC_CRS, 85 MX51_PAD_EIM_CS4__FEC_RX_ER, 86 NEW_PAD_CTRL(MX51_PAD_NANDF_D11__FEC_RX_DV, MX51_PAD_CTRL_4), 87 }; 88 89 imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); 90 } 91 92 #ifdef CONFIG_MXC_SPI 93 static void setup_iomux_spi(void) 94 { 95 static const iomux_v3_cfg_t spi_pads[] = { 96 NEW_PAD_CTRL(MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI, PAD_CTL_HYS | 97 PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST), 98 NEW_PAD_CTRL(MX51_PAD_CSPI1_MISO__ECSPI1_MISO, PAD_CTL_HYS | 99 PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST), 100 NEW_PAD_CTRL(MX51_PAD_CSPI1_SS1__ECSPI1_SS1, 101 MX51_GPIO_PAD_CTRL), 102 MX51_PAD_CSPI1_SS0__ECSPI1_SS0, 103 NEW_PAD_CTRL(MX51_PAD_CSPI1_RDY__ECSPI1_RDY, MX51_PAD_CTRL_2), 104 NEW_PAD_CTRL(MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK, PAD_CTL_HYS | 105 PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST), 106 }; 107 108 imx_iomux_v3_setup_multiple_pads(spi_pads, ARRAY_SIZE(spi_pads)); 109 } 110 #endif 111 112 #ifdef CONFIG_USB_EHCI_MX5 113 #define MX51EVK_USBH1_HUB_RST IMX_GPIO_NR(1, 7) 114 #define MX51EVK_USBH1_STP IMX_GPIO_NR(1, 27) 115 #define MX51EVK_USB_CLK_EN_B IMX_GPIO_NR(2, 2) 116 #define MX51EVK_USB_PHY_RESET IMX_GPIO_NR(2, 5) 117 118 static void setup_usb_h1(void) 119 { 120 static const iomux_v3_cfg_t usb_h1_pads[] = { 121 MX51_PAD_USBH1_CLK__USBH1_CLK, 122 MX51_PAD_USBH1_DIR__USBH1_DIR, 123 MX51_PAD_USBH1_STP__USBH1_STP, 124 MX51_PAD_USBH1_NXT__USBH1_NXT, 125 MX51_PAD_USBH1_DATA0__USBH1_DATA0, 126 MX51_PAD_USBH1_DATA1__USBH1_DATA1, 127 MX51_PAD_USBH1_DATA2__USBH1_DATA2, 128 MX51_PAD_USBH1_DATA3__USBH1_DATA3, 129 MX51_PAD_USBH1_DATA4__USBH1_DATA4, 130 MX51_PAD_USBH1_DATA5__USBH1_DATA5, 131 MX51_PAD_USBH1_DATA6__USBH1_DATA6, 132 MX51_PAD_USBH1_DATA7__USBH1_DATA7, 133 134 NEW_PAD_CTRL(MX51_PAD_GPIO1_7__GPIO1_7, 0), /* H1 hub reset */ 135 MX51_PAD_EIM_D17__GPIO2_1, 136 MX51_PAD_EIM_D21__GPIO2_5, /* PHY reset */ 137 }; 138 139 imx_iomux_v3_setup_multiple_pads(usb_h1_pads, ARRAY_SIZE(usb_h1_pads)); 140 } 141 142 int board_ehci_hcd_init(int port) 143 { 144 /* Set USBH1_STP to GPIO and toggle it */ 145 imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_USBH1_STP__GPIO1_27, 146 MX51_USBH_PAD_CTRL)); 147 148 gpio_direction_output(MX51EVK_USBH1_STP, 0); 149 gpio_direction_output(MX51EVK_USB_PHY_RESET, 0); 150 mdelay(10); 151 gpio_set_value(MX51EVK_USBH1_STP, 1); 152 153 /* Set back USBH1_STP to be function */ 154 imx_iomux_v3_setup_pad(MX51_PAD_USBH1_STP__USBH1_STP); 155 156 /* De-assert USB PHY RESETB */ 157 gpio_set_value(MX51EVK_USB_PHY_RESET, 1); 158 159 /* Drive USB_CLK_EN_B line low */ 160 gpio_direction_output(MX51EVK_USB_CLK_EN_B, 0); 161 162 /* Reset USB hub */ 163 gpio_direction_output(MX51EVK_USBH1_HUB_RST, 0); 164 mdelay(2); 165 gpio_set_value(MX51EVK_USBH1_HUB_RST, 1); 166 return 0; 167 } 168 #endif 169 170 static void power_init(void) 171 { 172 unsigned int val; 173 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE; 174 struct pmic *p; 175 int ret; 176 177 ret = pmic_init(I2C_PMIC); 178 if (ret) 179 return; 180 181 p = pmic_get("FSL_PMIC"); 182 if (!p) 183 return; 184 185 /* Write needed to Power Gate 2 register */ 186 pmic_reg_read(p, REG_POWER_MISC, &val); 187 val &= ~PWGT2SPIEN; 188 pmic_reg_write(p, REG_POWER_MISC, val); 189 190 /* Externally powered */ 191 pmic_reg_read(p, REG_CHARGE, &val); 192 val |= ICHRG0 | ICHRG1 | ICHRG2 | ICHRG3 | CHGAUTOB; 193 pmic_reg_write(p, REG_CHARGE, val); 194 195 /* power up the system first */ 196 pmic_reg_write(p, REG_POWER_MISC, PWUP); 197 198 /* Set core voltage to 1.1V */ 199 pmic_reg_read(p, REG_SW_0, &val); 200 val = (val & ~SWx_VOLT_MASK) | SWx_1_100V; 201 pmic_reg_write(p, REG_SW_0, val); 202 203 /* Setup VCC (SW2) to 1.25 */ 204 pmic_reg_read(p, REG_SW_1, &val); 205 val = (val & ~SWx_VOLT_MASK) | SWx_1_250V; 206 pmic_reg_write(p, REG_SW_1, val); 207 208 /* Setup 1V2_DIG1 (SW3) to 1.25 */ 209 pmic_reg_read(p, REG_SW_2, &val); 210 val = (val & ~SWx_VOLT_MASK) | SWx_1_250V; 211 pmic_reg_write(p, REG_SW_2, val); 212 udelay(50); 213 214 /* Raise the core frequency to 800MHz */ 215 writel(0x0, &mxc_ccm->cacrr); 216 217 /* Set switchers in Auto in NORMAL mode & STANDBY mode */ 218 /* Setup the switcher mode for SW1 & SW2*/ 219 pmic_reg_read(p, REG_SW_4, &val); 220 val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) | 221 (SWMODE_MASK << SWMODE2_SHIFT))); 222 val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) | 223 (SWMODE_AUTO_AUTO << SWMODE2_SHIFT); 224 pmic_reg_write(p, REG_SW_4, val); 225 226 /* Setup the switcher mode for SW3 & SW4 */ 227 pmic_reg_read(p, REG_SW_5, &val); 228 val = (val & ~((SWMODE_MASK << SWMODE3_SHIFT) | 229 (SWMODE_MASK << SWMODE4_SHIFT))); 230 val |= (SWMODE_AUTO_AUTO << SWMODE3_SHIFT) | 231 (SWMODE_AUTO_AUTO << SWMODE4_SHIFT); 232 pmic_reg_write(p, REG_SW_5, val); 233 234 /* Set VDIG to 1.65V, VGEN3 to 1.8V, VCAM to 2.6V */ 235 pmic_reg_read(p, REG_SETTING_0, &val); 236 val &= ~(VCAM_MASK | VGEN3_MASK | VDIG_MASK); 237 val |= VDIG_1_65 | VGEN3_1_8 | VCAM_2_6; 238 pmic_reg_write(p, REG_SETTING_0, val); 239 240 /* Set VVIDEO to 2.775V, VAUDIO to 3V, VSD to 3.15V */ 241 pmic_reg_read(p, REG_SETTING_1, &val); 242 val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK); 243 val |= VSD_3_15 | VAUDIO_3_0 | VVIDEO_2_775; 244 pmic_reg_write(p, REG_SETTING_1, val); 245 246 /* Configure VGEN3 and VCAM regulators to use external PNP */ 247 val = VGEN3CONFIG | VCAMCONFIG; 248 pmic_reg_write(p, REG_MODE_1, val); 249 udelay(200); 250 251 /* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */ 252 val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG | 253 VVIDEOEN | VAUDIOEN | VSDEN; 254 pmic_reg_write(p, REG_MODE_1, val); 255 256 imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_EIM_A20__GPIO2_14, 257 NO_PAD_CTRL)); 258 gpio_direction_output(IMX_GPIO_NR(2, 14), 0); 259 260 udelay(500); 261 262 gpio_set_value(IMX_GPIO_NR(2, 14), 1); 263 } 264 265 #ifdef CONFIG_FSL_ESDHC 266 int board_mmc_getcd(struct mmc *mmc) 267 { 268 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 269 int ret; 270 271 imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_0__GPIO1_0, 272 NO_PAD_CTRL)); 273 gpio_direction_input(IMX_GPIO_NR(1, 0)); 274 imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6, 275 NO_PAD_CTRL)); 276 gpio_direction_input(IMX_GPIO_NR(1, 6)); 277 278 if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR) 279 ret = !gpio_get_value(IMX_GPIO_NR(1, 0)); 280 else 281 ret = !gpio_get_value(IMX_GPIO_NR(1, 6)); 282 283 return ret; 284 } 285 286 int board_mmc_init(bd_t *bis) 287 { 288 static const iomux_v3_cfg_t sd1_pads[] = { 289 NEW_PAD_CTRL(MX51_PAD_SD1_CMD__SD1_CMD, PAD_CTL_DSE_MAX | 290 PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST), 291 NEW_PAD_CTRL(MX51_PAD_SD1_CLK__SD1_CLK, PAD_CTL_DSE_MAX | 292 PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST), 293 NEW_PAD_CTRL(MX51_PAD_SD1_DATA0__SD1_DATA0, PAD_CTL_DSE_MAX | 294 PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST), 295 NEW_PAD_CTRL(MX51_PAD_SD1_DATA1__SD1_DATA1, PAD_CTL_DSE_MAX | 296 PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST), 297 NEW_PAD_CTRL(MX51_PAD_SD1_DATA2__SD1_DATA2, PAD_CTL_DSE_MAX | 298 PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST), 299 NEW_PAD_CTRL(MX51_PAD_SD1_DATA3__SD1_DATA3, PAD_CTL_DSE_MAX | 300 PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SRE_FAST), 301 NEW_PAD_CTRL(MX51_PAD_GPIO1_0__SD1_CD, PAD_CTL_HYS), 302 NEW_PAD_CTRL(MX51_PAD_GPIO1_1__SD1_WP, PAD_CTL_HYS), 303 }; 304 305 static const iomux_v3_cfg_t sd2_pads[] = { 306 NEW_PAD_CTRL(MX51_PAD_SD2_CMD__SD2_CMD, 307 PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST), 308 NEW_PAD_CTRL(MX51_PAD_SD2_CLK__SD2_CLK, 309 PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST), 310 NEW_PAD_CTRL(MX51_PAD_SD2_DATA0__SD2_DATA0, 311 PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST), 312 NEW_PAD_CTRL(MX51_PAD_SD2_DATA1__SD2_DATA1, 313 PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST), 314 NEW_PAD_CTRL(MX51_PAD_SD2_DATA2__SD2_DATA2, 315 PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST), 316 NEW_PAD_CTRL(MX51_PAD_SD2_DATA3__SD2_DATA3, 317 PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST), 318 NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6, PAD_CTL_HYS), 319 NEW_PAD_CTRL(MX51_PAD_GPIO1_5__GPIO1_5, PAD_CTL_HYS), 320 }; 321 322 u32 index; 323 s32 status = 0; 324 325 esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 326 esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 327 328 for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; 329 index++) { 330 switch (index) { 331 case 0: 332 imx_iomux_v3_setup_multiple_pads(sd1_pads, 333 ARRAY_SIZE(sd1_pads)); 334 break; 335 case 1: 336 imx_iomux_v3_setup_multiple_pads(sd2_pads, 337 ARRAY_SIZE(sd2_pads)); 338 break; 339 default: 340 printf("Warning: you configured more ESDHC controller" 341 "(%d) as supported by the board(2)\n", 342 CONFIG_SYS_FSL_ESDHC_NUM); 343 return status; 344 } 345 status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]); 346 } 347 return status; 348 } 349 #endif 350 351 int board_early_init_f(void) 352 { 353 setup_iomux_uart(); 354 setup_iomux_fec(); 355 #ifdef CONFIG_USB_EHCI_MX5 356 setup_usb_h1(); 357 #endif 358 setup_iomux_lcd(); 359 360 return 0; 361 } 362 363 int board_init(void) 364 { 365 /* address of boot parameters */ 366 gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; 367 368 return 0; 369 } 370 371 #ifdef CONFIG_BOARD_LATE_INIT 372 int board_late_init(void) 373 { 374 #ifdef CONFIG_MXC_SPI 375 setup_iomux_spi(); 376 power_init(); 377 #endif 378 379 return 0; 380 } 381 #endif 382 383 /* 384 * Do not overwrite the console 385 * Use always serial for U-Boot console 386 */ 387 int overwrite_console(void) 388 { 389 return 1; 390 } 391 392 int checkboard(void) 393 { 394 puts("Board: MX51EVK\n"); 395 396 return 0; 397 } 398