1 /* 2 * Copyright 2006, 2007, 2010-2011 Freescale Semiconductor. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <pci.h> 9 #include <asm/processor.h> 10 #include <asm/immap_86xx.h> 11 #include <asm/fsl_pci.h> 12 #include <fsl_ddr_sdram.h> 13 #include <asm/fsl_serdes.h> 14 #include <asm/io.h> 15 #include <libfdt.h> 16 #include <fdt_support.h> 17 #include <netdev.h> 18 19 phys_size_t fixed_sdram(void); 20 21 int checkboard(void) 22 { 23 u8 vboot; 24 u8 *pixis_base = (u8 *)PIXIS_BASE; 25 26 printf ("Board: MPC8641HPCN, Sys ID: 0x%02x, " 27 "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", 28 in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER), 29 in_8(pixis_base + PIXIS_PVER)); 30 31 vboot = in_8(pixis_base + PIXIS_VBOOT); 32 if (vboot & PIXIS_VBOOT_FMAP) 33 printf ("vBank: %d\n", ((vboot & PIXIS_VBOOT_FBANK) >> 6)); 34 else 35 puts ("Promjet\n"); 36 37 return 0; 38 } 39 40 phys_size_t 41 initdram(int board_type) 42 { 43 phys_size_t dram_size = 0; 44 45 #if defined(CONFIG_SPD_EEPROM) 46 dram_size = fsl_ddr_sdram(); 47 #else 48 dram_size = fixed_sdram(); 49 #endif 50 51 setup_ddr_bat(dram_size); 52 53 debug(" DDR: "); 54 return dram_size; 55 } 56 57 58 #if !defined(CONFIG_SPD_EEPROM) 59 /* 60 * Fixed sdram init -- doesn't use serial presence detect. 61 */ 62 phys_size_t 63 fixed_sdram(void) 64 { 65 #if !defined(CONFIG_SYS_RAMBOOT) 66 volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; 67 struct ccsr_ddr __iomem *ddr = &immap->im_ddr1; 68 69 ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS; 70 ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG; 71 ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3; 72 ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0; 73 ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1; 74 ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2; 75 ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1; 76 ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2; 77 ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL; 78 ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT; 79 ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL; 80 ddr->sdram_ocd_cntl = CONFIG_SYS_DDR_OCD_CTRL; 81 ddr->sdram_ocd_status = CONFIG_SYS_DDR_OCD_STATUS; 82 83 #if defined (CONFIG_DDR_ECC) 84 ddr->err_disable = 0x0000008D; 85 ddr->err_sbe = 0x00ff0000; 86 #endif 87 asm("sync;isync"); 88 89 udelay(500); 90 91 #if defined (CONFIG_DDR_ECC) 92 /* Enable ECC checking */ 93 ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000); 94 #else 95 ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL; 96 ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2; 97 #endif 98 asm("sync; isync"); 99 100 udelay(500); 101 #endif 102 return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; 103 } 104 #endif /* !defined(CONFIG_SPD_EEPROM) */ 105 106 void pci_init_board(void) 107 { 108 fsl_pcie_init_board(0); 109 110 #ifdef CONFIG_PCIE1 111 /* 112 * Activate ULI1575 legacy chip by performing a fake 113 * memory access. Needed to make ULI RTC work. 114 */ 115 in_be32((unsigned *) ((char *)(CONFIG_SYS_PCIE1_MEM_VIRT 116 + CONFIG_SYS_PCIE1_MEM_SIZE - 0x1000000))); 117 #endif /* CONFIG_PCIE1 */ 118 } 119 120 121 #if defined(CONFIG_OF_BOARD_SETUP) 122 void 123 ft_board_setup(void *blob, bd_t *bd) 124 { 125 int off; 126 u64 *tmp; 127 u32 *addrcells; 128 129 ft_cpu_setup(blob, bd); 130 131 FT_FSL_PCI_SETUP; 132 133 /* 134 * Warn if it looks like the device tree doesn't match u-boot. 135 * This is just an estimation, based on the location of CCSR, 136 * which is defined by the "reg" property in the soc node. 137 */ 138 off = fdt_path_offset(blob, "/soc8641"); 139 addrcells = (u32 *)fdt_getprop(blob, 0, "#address-cells", NULL); 140 tmp = (u64 *)fdt_getprop(blob, off, "reg", NULL); 141 142 if (tmp) { 143 u64 addr; 144 if (addrcells && (*addrcells == 1)) 145 addr = *(u32 *)tmp; 146 else 147 addr = *tmp; 148 149 if (addr != CONFIG_SYS_CCSRBAR_PHYS) 150 printf("WARNING: The CCSRBAR address in your .dts " 151 "does not match the address of the CCSR " 152 "in u-boot. This means your .dts might " 153 "be old.\n"); 154 } 155 } 156 #endif 157 158 159 /* 160 * get_board_sys_clk 161 * Reads the FPGA on board for CONFIG_SYS_CLK_FREQ 162 */ 163 164 unsigned long 165 get_board_sys_clk(ulong dummy) 166 { 167 u8 i, go_bit, rd_clks; 168 ulong val = 0; 169 u8 *pixis_base = (u8 *)PIXIS_BASE; 170 171 go_bit = in_8(pixis_base + PIXIS_VCTL); 172 go_bit &= 0x01; 173 174 rd_clks = in_8(pixis_base + PIXIS_VCFGEN0); 175 rd_clks &= 0x1C; 176 177 /* 178 * Only if both go bit and the SCLK bit in VCFGEN0 are set 179 * should we be using the AUX register. Remember, we also set the 180 * GO bit to boot from the alternate bank on the on-board flash 181 */ 182 183 if (go_bit) { 184 if (rd_clks == 0x1c) 185 i = in_8(pixis_base + PIXIS_AUX); 186 else 187 i = in_8(pixis_base + PIXIS_SPD); 188 } else { 189 i = in_8(pixis_base + PIXIS_SPD); 190 } 191 192 i &= 0x07; 193 194 switch (i) { 195 case 0: 196 val = 33000000; 197 break; 198 case 1: 199 val = 40000000; 200 break; 201 case 2: 202 val = 50000000; 203 break; 204 case 3: 205 val = 66000000; 206 break; 207 case 4: 208 val = 83000000; 209 break; 210 case 5: 211 val = 100000000; 212 break; 213 case 6: 214 val = 134000000; 215 break; 216 case 7: 217 val = 166000000; 218 break; 219 } 220 221 return val; 222 } 223 224 int board_eth_init(bd_t *bis) 225 { 226 /* Initialize TSECs */ 227 cpu_eth_init(bis); 228 return pci_eth_init(bis); 229 } 230 231 void board_reset(void) 232 { 233 u8 *pixis_base = (u8 *)PIXIS_BASE; 234 235 out_8(pixis_base + PIXIS_RST, 0); 236 237 while (1) 238 ; 239 } 240