1 /* 2 * Copyright 2007,2009-2011 Freescale Semiconductor, Inc. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 #include <common.h> 24 #include <command.h> 25 #include <pci.h> 26 #include <asm/processor.h> 27 #include <asm/immap_86xx.h> 28 #include <asm/fsl_pci.h> 29 #include <asm/fsl_ddr_sdram.h> 30 #include <asm/fsl_serdes.h> 31 #include <i2c.h> 32 #include <asm/io.h> 33 #include <libfdt.h> 34 #include <fdt_support.h> 35 #include <spd_sdram.h> 36 #include <netdev.h> 37 38 void sdram_init(void); 39 phys_size_t fixed_sdram(void); 40 int mpc8610hpcd_diu_init(void); 41 42 43 /* called before any console output */ 44 int board_early_init_f(void) 45 { 46 volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; 47 volatile ccsr_gur_t *gur = &immap->im_gur; 48 49 gur->gpiocr |= 0x88aa5500; /* DIU16, IR1, UART0, UART2 */ 50 51 return 0; 52 } 53 54 int misc_init_r(void) 55 { 56 u8 tmp_val, version; 57 u8 *pixis_base = (u8 *)PIXIS_BASE; 58 59 /*Do not use 8259PIC*/ 60 tmp_val = in_8(pixis_base + PIXIS_BRDCFG0); 61 out_8(pixis_base + PIXIS_BRDCFG0, tmp_val | 0x80); 62 63 /*For FPGA V7 or higher, set the IRQMAPSEL to 0 to use MAP0 interrupt*/ 64 version = in_8(pixis_base + PIXIS_PVER); 65 if(version >= 0x07) { 66 tmp_val = in_8(pixis_base + PIXIS_BRDCFG0); 67 out_8(pixis_base + PIXIS_BRDCFG0, tmp_val & 0xbf); 68 } 69 70 /* Using this for DIU init before the driver in linux takes over 71 * Enable the TFP410 Encoder (I2C address 0x38) 72 */ 73 74 tmp_val = 0xBF; 75 i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); 76 /* Verify if enabled */ 77 tmp_val = 0; 78 i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); 79 debug("DVI Encoder Read: 0x%02x\n", tmp_val); 80 81 tmp_val = 0x10; 82 i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); 83 /* Verify if enabled */ 84 tmp_val = 0; 85 i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); 86 debug("DVI Encoder Read: 0x%02x\n", tmp_val); 87 88 return 0; 89 } 90 91 int checkboard(void) 92 { 93 volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; 94 volatile ccsr_local_mcm_t *mcm = &immap->im_local_mcm; 95 u8 *pixis_base = (u8 *)PIXIS_BASE; 96 97 printf ("Board: MPC8610HPCD, Sys ID: 0x%02x, " 98 "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", 99 in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER), 100 in_8(pixis_base + PIXIS_PVER)); 101 102 /* 103 * The MPC8610 HPCD workbook says that LBMAP=11 is the "normal" boot 104 * bank and LBMAP=00 is the alternate bank. However, the pixis 105 * altbank code can only set bits, not clear them, so we treat 00 as 106 * the normal bank and 11 as the alternate. 107 */ 108 switch (in_8(pixis_base + PIXIS_VBOOT) & 0xC0) { 109 case 0: 110 puts("vBank: Standard\n"); 111 break; 112 case 0x40: 113 puts("Promjet\n"); 114 break; 115 case 0x80: 116 puts("NAND\n"); 117 break; 118 case 0xC0: 119 puts("vBank: Alternate\n"); 120 break; 121 } 122 123 mcm->abcr |= 0x00010000; /* 0 */ 124 mcm->hpmr3 = 0x80000008; /* 4c */ 125 mcm->hpmr0 = 0; 126 mcm->hpmr1 = 0; 127 mcm->hpmr2 = 0; 128 mcm->hpmr4 = 0; 129 mcm->hpmr5 = 0; 130 131 return 0; 132 } 133 134 135 phys_size_t 136 initdram(int board_type) 137 { 138 phys_size_t dram_size = 0; 139 140 #if defined(CONFIG_SPD_EEPROM) 141 dram_size = fsl_ddr_sdram(); 142 #else 143 dram_size = fixed_sdram(); 144 #endif 145 146 setup_ddr_bat(dram_size); 147 148 debug(" DDR: "); 149 return dram_size; 150 } 151 152 153 #if !defined(CONFIG_SPD_EEPROM) 154 /* 155 * Fixed sdram init -- doesn't use serial presence detect. 156 */ 157 158 phys_size_t fixed_sdram(void) 159 { 160 #if !defined(CONFIG_SYS_RAMBOOT) 161 volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; 162 volatile ccsr_ddr_t *ddr = &immap->im_ddr1; 163 uint d_init; 164 165 ddr->cs0_bnds = 0x0000001f; 166 ddr->cs0_config = 0x80010202; 167 168 ddr->timing_cfg_3 = 0x00000000; 169 ddr->timing_cfg_0 = 0x00260802; 170 ddr->timing_cfg_1 = 0x3935d322; 171 ddr->timing_cfg_2 = 0x14904cc8; 172 ddr->sdram_mode = 0x00480432; 173 ddr->sdram_mode_2 = 0x00000000; 174 ddr->sdram_interval = 0x06180fff; /* 0x06180100; */ 175 ddr->sdram_data_init = 0xDEADBEEF; 176 ddr->sdram_clk_cntl = 0x03800000; 177 ddr->sdram_cfg_2 = 0x04400010; 178 179 #if defined(CONFIG_DDR_ECC) 180 ddr->err_int_en = 0x0000000d; 181 ddr->err_disable = 0x00000000; 182 ddr->err_sbe = 0x00010000; 183 #endif 184 asm("sync;isync"); 185 186 udelay(500); 187 188 ddr->sdram_cfg = 0xc3000000; /* 0xe3008000;*/ 189 190 191 #if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) 192 d_init = 1; 193 debug("DDR - 1st controller: memory initializing\n"); 194 /* 195 * Poll until memory is initialized. 196 * 512 Meg at 400 might hit this 200 times or so. 197 */ 198 while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) 199 udelay(1000); 200 201 debug("DDR: memory initialized\n\n"); 202 asm("sync; isync"); 203 udelay(500); 204 #endif 205 206 return 512 * 1024 * 1024; 207 #endif 208 return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; 209 } 210 211 #endif 212 213 #if defined(CONFIG_PCI) 214 /* 215 * Initialize PCI Devices, report devices found. 216 */ 217 218 #ifndef CONFIG_PCI_PNP 219 static struct pci_config_table pci_fsl86xxads_config_table[] = { 220 {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 221 PCI_IDSEL_NUMBER, PCI_ANY_ID, 222 pci_cfgfunc_config_device, {PCI_ENET0_IOADDR, 223 PCI_ENET0_MEMADDR, 224 PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER} }, 225 {} 226 }; 227 #endif 228 229 230 static struct pci_controller pci1_hose; 231 #endif /* CONFIG_PCI */ 232 233 void pci_init_board(void) 234 { 235 volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR; 236 volatile ccsr_gur_t *gur = &immap->im_gur; 237 struct fsl_pci_info pci_info; 238 u32 devdisr; 239 int first_free_busno; 240 int pci_agent; 241 242 devdisr = in_be32(&gur->devdisr); 243 244 first_free_busno = fsl_pcie_init_board(0); 245 246 #ifdef CONFIG_PCI1 247 if (!(devdisr & MPC86xx_DEVDISR_PCI1)) { 248 SET_STD_PCI_INFO(pci_info, 1); 249 set_next_law(pci_info.mem_phys, 250 law_size_bits(pci_info.mem_size), pci_info.law); 251 set_next_law(pci_info.io_phys, 252 law_size_bits(pci_info.io_size), pci_info.law); 253 254 pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs); 255 printf("PCI: connected to PCI slots as %s" \ 256 " (base address %lx)\n", 257 pci_agent ? "Agent" : "Host", 258 pci_info.regs); 259 #ifndef CONFIG_PCI_PNP 260 pci1_hose.config_table = pci_mpc86xxcts_config_table; 261 #endif 262 first_free_busno = fsl_pci_init_port(&pci_info, 263 &pci1_hose, first_free_busno); 264 } else { 265 printf("PCI: disabled\n"); 266 } 267 268 puts("\n"); 269 #else 270 setbits_be32(&gur->devdisr, MPC86xx_DEVDISR_PCI1); /* disable */ 271 #endif 272 273 fsl_pcie_init_board(first_free_busno); 274 } 275 276 #if defined(CONFIG_OF_BOARD_SETUP) 277 void 278 ft_board_setup(void *blob, bd_t *bd) 279 { 280 ft_cpu_setup(blob, bd); 281 282 FT_FSL_PCI_SETUP; 283 } 284 #endif 285 286 /* 287 * get_board_sys_clk 288 * Reads the FPGA on board for CONFIG_SYS_CLK_FREQ 289 */ 290 291 unsigned long 292 get_board_sys_clk(ulong dummy) 293 { 294 u8 i; 295 ulong val = 0; 296 u8 *pixis_base = (u8 *)PIXIS_BASE; 297 298 i = in_8(pixis_base + PIXIS_SPD); 299 i &= 0x07; 300 301 switch (i) { 302 case 0: 303 val = 33333000; 304 break; 305 case 1: 306 val = 39999600; 307 break; 308 case 2: 309 val = 49999500; 310 break; 311 case 3: 312 val = 66666000; 313 break; 314 case 4: 315 val = 83332500; 316 break; 317 case 5: 318 val = 99999000; 319 break; 320 case 6: 321 val = 133332000; 322 break; 323 case 7: 324 val = 166665000; 325 break; 326 } 327 328 return val; 329 } 330 331 int board_eth_init(bd_t *bis) 332 { 333 return pci_eth_init(bis); 334 } 335 336 void board_reset(void) 337 { 338 u8 *pixis_base = (u8 *)PIXIS_BASE; 339 340 out_8(pixis_base + PIXIS_RST, 0); 341 342 while (1) 343 ; 344 } 345