1Overview
2--------
3MPC8572DS is a high-performance computing, evaluation and development platform
4supporting the mpc8572 PowerTM processor.
5
6Building U-Boot
7-----------
8	make MPC8572DS_config
9	make
10
11Flash Banks
12-----------
13MPC8572DS board has two flash banks. They are both present on boot, but their
14locations can be swapped using the dip-switch SW9[1:2].
15
16Booting is always from the boot bank at 0xec00_0000.
17
18
19Memory Map
20----------
21
220xe800_0000 - 0xebff_ffff	Alternate bank		64MB
230xec00_0000 - 0xefff_ffff	Boot bank		64MB
24
250xebf8_0000 - 0xebff_ffff	Alternate U-Boot address	512KB
260xeff8_0000 - 0xefff_ffff	Boot U-Boot address		512KB
27
28
29Flashing Images
30---------------
31
32To place a new U-Boot image in the alternate flash bank and then reset with that
33 new image temporarily, use this:
34
35	tftp 1000000 u-boot.bin
36	erase ebf80000 ebffffff
37	cp.b 1000000 ebf80000 80000
38	pixis_reset altbank
39
40
41To program the image in the boot flash bank:
42
43	tftp 1000000 u-boot.bin
44	protect off all
45	erase eff80000 ffffffff
46	cp.b 1000000 eff80000 80000
47
48
49The pixis_reset command
50-----------------------
51The command - "pixis_reset", is introduced to reset mpc8572ds board
52using the FPGA sequencer.  When the board restarts, it has the option
53of using either the current or alternate flash bank as the boot
54image, with or without the watchdog timer enabled, and finally with
55or without frequency changes.
56
57Usage is;
58
59	pixis_reset
60	pixis_reset altbank
61	pixis_reset altbank wd
62	pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
63	pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
64
65Examples:
66
67	/* reset to current bank, like "reset" command */
68	pixis_reset
69
70	/* reset board but use the to alternate flash bank */
71	pixis_reset altbank
72
73
74Using the Device Tree Source File
75---------------------------------
76To create the DTB (Device Tree Binary) image file,
77use a command similar to this:
78
79	dtc -b 0 -f -I dts -O dtb mpc8572ds.dts > mpc8572ds.dtb
80
81Likely, that .dts file will come from here;
82
83	linux-2.6/arch/powerpc/boot/dts/mpc8572ds.dts
84
85
86Booting Linux
87-------------
88
89Place a linux uImage in the TFTP disk area.
90
91	tftp 1000000 uImage.8572
92	tftp c00000 mpc8572ds.dtb
93	bootm 1000000 - c00000
94
95
96Implementing AMP(Asymmetric MultiProcessing)
97-------------
981. Build kernel image for core0:
99
100	a. $ make 85xx/mpc8572_ds_defconfig
101
102	b. $ make menuconfig
103	   - un-select "Processor support"->"Symetric multi-processing support"
104
105	c. $ make uImage
106
107	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0
108
1092. Build kernel image for core1:
110
111	a. $ make 85xx/mpc8572_ds_defconfig
112
113	b. $ make menuconfig
114	   - Un-select "Processor support"->"Symetric multi-processing support"
115	   - Select "Advanced setup" -> " Prompt for advanced kernel
116	     configuration options"
117		- Select "Set physical address where the kernel is loaded" and
118		  set it to 0x20000000, assuming core1 will start from 512MB.
119		- Select "Set custom page offset address"
120		- Select "Set custom kernel base address"
121		- Select "Set maximum low memory"
122	   - "Exit" and save the selection.
123
124	c. $ make uImage
125
126	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1
127
1283. Create dtb for core0:
129
130	$ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
131
1324. Create dtb for core1:
133
134	$ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
135
1365. Bring up two cores separately:
137
138	a. Power on the board, under U-Boot prompt:
139		=> setenv <serverip>
140		=> setenv <ipaddr>
141		=> setenv bootargs root=/dev/ram rw console=ttyS0,115200
142	b. Bring up core1's kernel first:
143		=> setenv bootm_low 0x20000000
144		=> setenv bootm_size 0x10000000
145		=> tftp 21000000 8572/uImage.core1
146		=> tftp 22000000 8572/ramdiskfile
147		=> tftp 20c00000 8572/mpc8572ds_core1.dtb
148		=> interrupts off
149		=> bootm start 21000000 22000000 20c00000
150		=> bootm loados
151		=> bootm ramdisk
152		=> bootm fdt
153		=> fdt boardsetup
154		=> fdt chosen $initrd_start $initrd_end
155		=> bootm prep
156		=> cpu 1 release $bootm_low - $fdtaddr -
157	c. Bring up core0's kernel(on the same U-Boot console):
158		=> setenv bootm_low 0
159		=> setenv bootm_size 0x20000000
160		=> tftp 1000000 8572/uImage.core0
161		=> tftp 2000000 8572/ramdiskfile
162		=> tftp c00000 8572/mpc8572ds_core0.dtb
163		=> bootm 1000000 2000000 c00000
164
165Please note only core0 will run U-Boot, core1 starts kernel directly after
166"cpu release" command is issued.
167