1 /* 2 * Copyright 2009-2010 Freescale Semiconductor. 3 * 4 * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <console.h> 11 #include <hwconfig.h> 12 #include <pci.h> 13 #include <asm/processor.h> 14 #include <asm/mmu.h> 15 #include <asm/cache.h> 16 #include <asm/immap_85xx.h> 17 #include <asm/fsl_pci.h> 18 #include <fsl_ddr_sdram.h> 19 #include <asm/fsl_serdes.h> 20 #include <asm/io.h> 21 #include <spd_sdram.h> 22 #include <i2c.h> 23 #include <ioports.h> 24 #include <libfdt.h> 25 #include <fdt_support.h> 26 #include <fsl_esdhc.h> 27 #include <phy.h> 28 29 #include "bcsr.h" 30 #if defined(CONFIG_PQ_MDS_PIB) 31 #include "../common/pq-mds-pib.h" 32 #endif 33 34 const qe_iop_conf_t qe_iop_conf_tab[] = { 35 /* QE_MUX_MDC */ 36 {2, 31, 1, 0, 1}, /* QE_MUX_MDC */ 37 38 /* QE_MUX_MDIO */ 39 {2, 30, 3, 0, 2}, /* QE_MUX_MDIO */ 40 41 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 42 /* UCC_1_RGMII */ 43 {2, 11, 2, 0, 1}, /* CLK12 */ 44 {0, 0, 1, 0, 3}, /* ENET1_TXD0_SER1_TXD0 */ 45 {0, 1, 1, 0, 3}, /* ENET1_TXD1_SER1_TXD1 */ 46 {0, 2, 1, 0, 1}, /* ENET1_TXD2_SER1_TXD2 */ 47 {0, 3, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3 */ 48 {0, 6, 2, 0, 3}, /* ENET1_RXD0_SER1_RXD0 */ 49 {0, 7, 2, 0, 1}, /* ENET1_RXD1_SER1_RXD1 */ 50 {0, 8, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2 */ 51 {0, 9, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3 */ 52 {0, 4, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */ 53 {0, 12, 2, 0, 3}, /* ENET1_RX_DV_SER1_CTS_B */ 54 {2, 8, 2, 0, 1}, /* ENET1_GRXCLK */ 55 {2, 20, 1, 0, 2}, /* ENET1_GTXCLK */ 56 57 /* UCC_2_RGMII */ 58 {2, 16, 2, 0, 3}, /* CLK17 */ 59 {0, 14, 1, 0, 2}, /* ENET2_TXD0_SER2_TXD0 */ 60 {0, 15, 1, 0, 2}, /* ENET2_TXD1_SER2_TXD1 */ 61 {0, 16, 1, 0, 1}, /* ENET2_TXD2_SER2_TXD2 */ 62 {0, 17, 1, 0, 1}, /* ENET2_TXD3_SER2_TXD3 */ 63 {0, 20, 2, 0, 2}, /* ENET2_RXD0_SER2_RXD0 */ 64 {0, 21, 2, 0, 1}, /* ENET2_RXD1_SER2_RXD1 */ 65 {0, 22, 2, 0, 1}, /* ENET2_RXD2_SER2_RXD2 */ 66 {0, 23, 2, 0, 1}, /* ENET2_RXD3_SER2_RXD3 */ 67 {0, 18, 1, 0, 2}, /* ENET2_TX_EN_SER2_RTS_B */ 68 {0, 26, 2, 0, 3}, /* ENET2_RX_DV_SER2_CTS_B */ 69 {2, 3, 2, 0, 1}, /* ENET2_GRXCLK */ 70 {2, 2, 1, 0, 2}, /* ENET2_GTXCLK */ 71 72 /* UCC_3_RGMII */ 73 {2, 11, 2, 0, 1}, /* CLK12 */ 74 {0, 29, 1, 0, 2}, /* ENET3_TXD0_SER3_TXD0 */ 75 {0, 30, 1, 0, 3}, /* ENET3_TXD1_SER3_TXD1 */ 76 {0, 31, 1, 0, 2}, /* ENET3_TXD2_SER3_TXD2 */ 77 {1, 0, 1, 0, 3}, /* ENET3_TXD3_SER3_TXD3 */ 78 {1, 3, 2, 0, 3}, /* ENET3_RXD0_SER3_RXD0 */ 79 {1, 4, 2, 0, 1}, /* ENET3_RXD1_SER3_RXD1 */ 80 {1, 5, 2, 0, 2}, /* ENET3_RXD2_SER3_RXD2 */ 81 {1, 6, 2, 0, 3}, /* ENET3_RXD3_SER3_RXD3 */ 82 {1, 1, 1, 0, 1}, /* ENET3_TX_EN_SER3_RTS_B */ 83 {1, 9, 2, 0, 3}, /* ENET3_RX_DV_SER3_CTS_B */ 84 {2, 9, 2, 0, 2}, /* ENET3_GRXCLK */ 85 {2, 25, 1, 0, 2}, /* ENET3_GTXCLK */ 86 87 /* UCC_4_RGMII */ 88 {2, 16, 2, 0, 3}, /* CLK17 */ 89 {1, 12, 1, 0, 2}, /* ENET4_TXD0_SER4_TXD0 */ 90 {1, 13, 1, 0, 2}, /* ENET4_TXD1_SER4_TXD1 */ 91 {1, 14, 1, 0, 1}, /* ENET4_TXD2_SER4_TXD2 */ 92 {1, 15, 1, 0, 2}, /* ENET4_TXD3_SER4_TXD3 */ 93 {1, 18, 2, 0, 2}, /* ENET4_RXD0_SER4_RXD0 */ 94 {1, 19, 2, 0, 1}, /* ENET4_RXD1_SER4_RXD1 */ 95 {1, 20, 2, 0, 1}, /* ENET4_RXD2_SER4_RXD2 */ 96 {1, 21, 2, 0, 2}, /* ENET4_RXD3_SER4_RXD3 */ 97 {1, 16, 1, 0, 2}, /* ENET4_TX_EN_SER4_RTS_B */ 98 {1, 24, 2, 0, 3}, /* ENET4_RX_DV_SER4_CTS_B */ 99 {2, 17, 2, 0, 2}, /* ENET4_GRXCLK */ 100 {2, 24, 1, 0, 2}, /* ENET4_GTXCLK */ 101 102 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 103 /* UCC_1_RMII */ 104 {2, 15, 2, 0, 1}, /* CLK16 */ 105 {0, 0, 1, 0, 3}, /* ENET1_TXD0_SER1_TXD0 */ 106 {0, 1, 1, 0, 3}, /* ENET1_TXD1_SER1_TXD1 */ 107 {0, 6, 2, 0, 3}, /* ENET1_RXD0_SER1_RXD0 */ 108 {0, 7, 2, 0, 1}, /* ENET1_RXD1_SER1_RXD1 */ 109 {0, 4, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */ 110 {0, 12, 2, 0, 3}, /* ENET1_RX_DV_SER1_CTS_B */ 111 112 /* UCC_2_RMII */ 113 {2, 15, 2, 0, 1}, /* CLK16 */ 114 {0, 14, 1, 0, 2}, /* ENET2_TXD0_SER2_TXD0 */ 115 {0, 15, 1, 0, 2}, /* ENET2_TXD1_SER2_TXD1 */ 116 {0, 20, 2, 0, 2}, /* ENET2_RXD0_SER2_RXD0 */ 117 {0, 21, 2, 0, 1}, /* ENET2_RXD1_SER2_RXD1 */ 118 {0, 18, 1, 0, 2}, /* ENET2_TX_EN_SER2_RTS_B */ 119 {0, 26, 2, 0, 3}, /* ENET2_RX_DV_SER2_CTS_B */ 120 121 /* UCC_3_RMII */ 122 {2, 15, 2, 0, 1}, /* CLK16 */ 123 {0, 29, 1, 0, 2}, /* ENET3_TXD0_SER3_TXD0 */ 124 {0, 30, 1, 0, 3}, /* ENET3_TXD1_SER3_TXD1 */ 125 {1, 3, 2, 0, 3}, /* ENET3_RXD0_SER3_RXD0 */ 126 {1, 4, 2, 0, 1}, /* ENET3_RXD1_SER3_RXD1 */ 127 {1, 1, 1, 0, 1}, /* ENET3_TX_EN_SER3_RTS_B */ 128 {1, 9, 2, 0, 3}, /* ENET3_RX_DV_SER3_CTS_B */ 129 130 /* UCC_4_RMII */ 131 {2, 15, 2, 0, 1}, /* CLK16 */ 132 {1, 12, 1, 0, 2}, /* ENET4_TXD0_SER4_TXD0 */ 133 {1, 13, 1, 0, 2}, /* ENET4_TXD1_SER4_TXD1 */ 134 {1, 18, 2, 0, 2}, /* ENET4_RXD0_SER4_RXD0 */ 135 {1, 19, 2, 0, 1}, /* ENET4_RXD1_SER4_RXD1 */ 136 {1, 16, 1, 0, 2}, /* ENET4_TX_EN_SER4_RTS_B */ 137 {1, 24, 2, 0, 3}, /* ENET4_RX_DV_SER4_CTS_B */ 138 #endif 139 140 /* UART1 is muxed with QE PortF bit [9-12].*/ 141 {5, 12, 2, 0, 3}, /* UART1_SIN */ 142 {5, 9, 1, 0, 3}, /* UART1_SOUT */ 143 {5, 10, 2, 0, 3}, /* UART1_CTS_B */ 144 {5, 11, 1, 0, 2}, /* UART1_RTS_B */ 145 146 /* QE UART */ 147 {0, 19, 1, 0, 2}, /* QEUART_TX */ 148 {1, 17, 2, 0, 3}, /* QEUART_RX */ 149 {0, 25, 1, 0, 1}, /* QEUART_RTS */ 150 {1, 23, 2, 0, 1}, /* QEUART_CTS */ 151 152 /* QE USB */ 153 {5, 3, 1, 0, 1}, /* USB_OE */ 154 {5, 4, 1, 0, 2}, /* USB_TP */ 155 {5, 5, 1, 0, 2}, /* USB_TN */ 156 {5, 6, 2, 0, 2}, /* USB_RP */ 157 {5, 7, 2, 0, 1}, /* USB_RX */ 158 {5, 8, 2, 0, 1}, /* USB_RN */ 159 {2, 4, 2, 0, 2}, /* CLK5 */ 160 161 /* SPI Flash, M25P40 */ 162 {4, 27, 3, 0, 1}, /* SPI_MOSI */ 163 {4, 28, 3, 0, 1}, /* SPI_MISO */ 164 {4, 29, 3, 0, 1}, /* SPI_CLK */ 165 {4, 30, 1, 0, 0}, /* SPI_SEL, GPIO */ 166 167 {0, 0, 0, 0, QE_IOP_TAB_END} /* END of table */ 168 }; 169 170 void local_bus_init(void); 171 172 int board_early_init_f (void) 173 { 174 /* 175 * Initialize local bus. 176 */ 177 local_bus_init (); 178 179 enable_8569mds_flash_write(); 180 181 #ifdef CONFIG_QE 182 enable_8569mds_qe_uec(); 183 #endif 184 185 #if CONFIG_SYS_I2C2_OFFSET 186 /* Enable I2C2 signals instead of SD signals */ 187 volatile struct ccsr_gur *gur; 188 gur = (struct ccsr_gur *)(CONFIG_SYS_IMMR + 0xe0000); 189 gur->plppar1 &= ~PLPPAR1_I2C_BIT_MASK; 190 gur->plppar1 |= PLPPAR1_I2C2_VAL; 191 gur->plpdir1 &= ~PLPDIR1_I2C_BIT_MASK; 192 gur->plpdir1 |= PLPDIR1_I2C2_VAL; 193 194 disable_8569mds_brd_eeprom_write_protect(); 195 #endif 196 197 return 0; 198 } 199 200 int board_early_init_r(void) 201 { 202 const unsigned int flashbase = CONFIG_SYS_NAND_BASE; 203 const u8 flash_esel = 0; 204 205 /* 206 * Remap Boot flash to caching-inhibited 207 * so that flash can be erased properly. 208 */ 209 210 /* Flush d-cache and invalidate i-cache of any FLASH data */ 211 flush_dcache(); 212 invalidate_icache(); 213 214 /* invalidate existing TLB entry for flash */ 215 disable_tlb(flash_esel); 216 217 set_tlb(1, flashbase, CONFIG_SYS_NAND_BASE, /* tlb, epn, rpn */ 218 MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */ 219 0, flash_esel, /* ts, esel */ 220 BOOKE_PAGESZ_64M, 1); /* tsize, iprot */ 221 222 return 0; 223 } 224 225 int checkboard (void) 226 { 227 printf ("Board: 8569 MDS\n"); 228 229 return 0; 230 } 231 232 #if !defined(CONFIG_SPD_EEPROM) 233 phys_size_t fixed_sdram(void) 234 { 235 struct ccsr_ddr __iomem *ddr = 236 (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR; 237 uint d_init; 238 239 out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); 240 out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG); 241 out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); 242 out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); 243 out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); 244 out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); 245 out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG); 246 out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_SDRAM_CFG_2); 247 out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_SDRAM_MODE); 248 out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_SDRAM_MODE_2); 249 out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_SDRAM_INTERVAL); 250 out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT); 251 out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL); 252 out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4); 253 out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5); 254 out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL); 255 out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL); 256 out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_SDRAM_CFG_2); 257 #if defined (CONFIG_DDR_ECC) 258 out_be32(&ddr->err_int_en, CONFIG_SYS_DDR_ERR_INT_EN); 259 out_be32(&ddr->err_disable, CONFIG_SYS_DDR_ERR_DIS); 260 out_be32(&ddr->err_sbe, CONFIG_SYS_DDR_SBE); 261 #endif 262 udelay(500); 263 264 out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL); 265 #if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) 266 d_init = 1; 267 debug("DDR - 1st controller: memory initializing\n"); 268 /* 269 * Poll until memory is initialized. 270 * 512 Meg at 400 might hit this 200 times or so. 271 */ 272 while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) { 273 udelay(1000); 274 } 275 debug("DDR: memory initialized\n\n"); 276 udelay(500); 277 #endif 278 return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; 279 } 280 #endif 281 282 /* 283 * Initialize Local Bus 284 */ 285 void 286 local_bus_init(void) 287 { 288 volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 289 volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; 290 291 uint clkdiv; 292 sys_info_t sysinfo; 293 294 get_sys_info(&sysinfo); 295 clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; 296 297 out_be32(&gur->lbiuiplldcr1, 0x00078080); 298 if (clkdiv == 16) 299 out_be32(&gur->lbiuiplldcr0, 0x7c0f1bf0); 300 else if (clkdiv == 8) 301 out_be32(&gur->lbiuiplldcr0, 0x6c0f1bf0); 302 else if (clkdiv == 4) 303 out_be32(&gur->lbiuiplldcr0, 0x5c0f1bf0); 304 305 out_be32(&lbc->lcrr, (u32)in_be32(&lbc->lcrr)| 0x00030000); 306 } 307 308 static void fdt_board_disable_serial(void *blob, bd_t *bd, const char *alias) 309 { 310 const char *status = "disabled"; 311 int off; 312 int err; 313 314 off = fdt_path_offset(blob, alias); 315 if (off < 0) { 316 printf("WARNING: could not find %s alias: %s.\n", alias, 317 fdt_strerror(off)); 318 return; 319 } 320 321 err = fdt_setprop(blob, off, "status", status, strlen(status) + 1); 322 if (err) { 323 printf("WARNING: could not set status for serial0: %s.\n", 324 fdt_strerror(err)); 325 return; 326 } 327 } 328 329 /* 330 * Because of an erratum in prototype boards it is impossible to use eSDHC 331 * without disabling UART0 (which makes it quite easy to 'brick' the board 332 * by simply issung 'setenv hwconfig esdhc', and not able to interact with 333 * U-Boot anylonger). 334 * 335 * So, but default we assume that the board is a prototype, which is a most 336 * safe assumption. There is no way to determine board revision from a 337 * register, so we use hwconfig. 338 */ 339 340 static int prototype_board(void) 341 { 342 if (hwconfig_subarg("board", "rev", NULL)) 343 return hwconfig_subarg_cmp("board", "rev", "prototype"); 344 return 1; 345 } 346 347 static int esdhc_disables_uart0(void) 348 { 349 return prototype_board() || 350 hwconfig_subarg_cmp("esdhc", "mode", "4-bits"); 351 } 352 353 static void fdt_board_fixup_qe_uart(void *blob, bd_t *bd) 354 { 355 u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE; 356 const char *devtype = "serial"; 357 const char *compat = "ucc_uart"; 358 const char *clk = "brg9"; 359 u32 portnum = 0; 360 int off = -1; 361 362 if (!hwconfig("qe_uart")) 363 return; 364 365 if (hwconfig("esdhc") && esdhc_disables_uart0()) { 366 printf("QE UART: won't enable with esdhc.\n"); 367 return; 368 } 369 370 fdt_board_disable_serial(blob, bd, "serial1"); 371 372 while (1) { 373 const u32 *idx; 374 int len; 375 376 off = fdt_node_offset_by_compatible(blob, off, "ucc_geth"); 377 if (off < 0) { 378 printf("WARNING: unable to fixup device tree for " 379 "QE UART\n"); 380 return; 381 } 382 383 idx = fdt_getprop(blob, off, "cell-index", &len); 384 if (!idx || len != sizeof(*idx) || *idx != fdt32_to_cpu(2)) 385 continue; 386 break; 387 } 388 389 fdt_setprop(blob, off, "device_type", devtype, strlen(devtype) + 1); 390 fdt_setprop(blob, off, "compatible", compat, strlen(compat) + 1); 391 fdt_setprop(blob, off, "tx-clock-name", clk, strlen(clk) + 1); 392 fdt_setprop(blob, off, "rx-clock-name", clk, strlen(clk) + 1); 393 fdt_setprop(blob, off, "port-number", &portnum, sizeof(portnum)); 394 395 setbits_8(&bcsr[15], BCSR15_QEUART_EN); 396 } 397 398 #ifdef CONFIG_FSL_ESDHC 399 400 int board_mmc_init(bd_t *bd) 401 { 402 struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_MPC85xx_GUTS_ADDR; 403 u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE; 404 u8 bcsr6 = BCSR6_SD_CARD_1BIT; 405 406 if (!hwconfig("esdhc")) 407 return 0; 408 409 printf("Enabling eSDHC...\n" 410 " For eSDHC to function, I2C2 "); 411 if (esdhc_disables_uart0()) { 412 printf("and UART0 should be disabled.\n"); 413 printf(" Redirecting stderr, stdout and stdin to UART1...\n"); 414 console_assign(stderr, "eserial1"); 415 console_assign(stdout, "eserial1"); 416 console_assign(stdin, "eserial1"); 417 printf("Switched to UART1 (initial log has been printed to " 418 "UART0).\n"); 419 420 clrsetbits_be32(&gur->plppar1, PLPPAR1_UART0_BIT_MASK, 421 PLPPAR1_ESDHC_4BITS_VAL); 422 clrsetbits_be32(&gur->plpdir1, PLPDIR1_UART0_BIT_MASK, 423 PLPDIR1_ESDHC_4BITS_VAL); 424 bcsr6 |= BCSR6_SD_CARD_4BITS; 425 } else { 426 printf("should be disabled.\n"); 427 } 428 429 /* Assign I2C2 signals to eSDHC. */ 430 clrsetbits_be32(&gur->plppar1, PLPPAR1_I2C_BIT_MASK, 431 PLPPAR1_ESDHC_VAL); 432 clrsetbits_be32(&gur->plpdir1, PLPDIR1_I2C_BIT_MASK, 433 PLPDIR1_ESDHC_VAL); 434 435 /* Mux I2C2 (and optionally UART0) signals to eSDHC. */ 436 setbits_8(&bcsr[6], bcsr6); 437 438 return fsl_esdhc_mmc_init(bd); 439 } 440 441 static void fdt_board_fixup_esdhc(void *blob, bd_t *bd) 442 { 443 const char *status = "disabled"; 444 int off = -1; 445 446 if (!hwconfig("esdhc")) 447 return; 448 449 if (esdhc_disables_uart0()) 450 fdt_board_disable_serial(blob, bd, "serial0"); 451 452 while (1) { 453 const u32 *idx; 454 int len; 455 456 off = fdt_node_offset_by_compatible(blob, off, "fsl-i2c"); 457 if (off < 0) 458 break; 459 460 idx = fdt_getprop(blob, off, "cell-index", &len); 461 if (!idx || len != sizeof(*idx)) 462 continue; 463 464 if (*idx == 1) { 465 fdt_setprop(blob, off, "status", status, 466 strlen(status) + 1); 467 break; 468 } 469 } 470 471 if (hwconfig_subarg_cmp("esdhc", "mode", "4-bits")) { 472 off = fdt_node_offset_by_compatible(blob, -1, "fsl,esdhc"); 473 if (off < 0) { 474 printf("WARNING: could not find esdhc node\n"); 475 return; 476 } 477 fdt_delprop(blob, off, "sdhci,1-bit-only"); 478 } 479 } 480 #else 481 static inline void fdt_board_fixup_esdhc(void *blob, bd_t *bd) {} 482 #endif 483 484 static void fdt_board_fixup_qe_usb(void *blob, bd_t *bd) 485 { 486 u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE; 487 488 if (hwconfig_subarg_cmp("qe_usb", "speed", "low")) 489 clrbits_8(&bcsr[17], BCSR17_nUSBLOWSPD); 490 else 491 setbits_8(&bcsr[17], BCSR17_nUSBLOWSPD); 492 493 if (hwconfig_subarg_cmp("qe_usb", "mode", "peripheral")) { 494 clrbits_8(&bcsr[17], BCSR17_USBVCC); 495 clrbits_8(&bcsr[17], BCSR17_USBMODE); 496 do_fixup_by_compat(blob, "fsl,mpc8569-qe-usb", "mode", 497 "peripheral", sizeof("peripheral"), 1); 498 } else { 499 setbits_8(&bcsr[17], BCSR17_USBVCC); 500 setbits_8(&bcsr[17], BCSR17_USBMODE); 501 } 502 503 clrbits_8(&bcsr[17], BCSR17_nUSBEN); 504 } 505 506 #ifdef CONFIG_PCI 507 void pci_init_board(void) 508 { 509 #if defined(CONFIG_PQ_MDS_PIB) 510 pib_init(); 511 #endif 512 513 fsl_pcie_init_board(0); 514 } 515 #endif /* CONFIG_PCI */ 516 517 #if defined(CONFIG_OF_BOARD_SETUP) 518 int ft_board_setup(void *blob, bd_t *bd) 519 { 520 #if defined(CONFIG_SYS_UCC_RMII_MODE) 521 int nodeoff, off, err; 522 unsigned int val; 523 const u32 *ph; 524 const u32 *index; 525 526 /* fixup device tree for supporting rmii mode */ 527 nodeoff = -1; 528 while ((nodeoff = fdt_node_offset_by_compatible(blob, nodeoff, 529 "ucc_geth")) >= 0) { 530 err = fdt_setprop_string(blob, nodeoff, "tx-clock-name", 531 "clk16"); 532 if (err < 0) { 533 printf("WARNING: could not set tx-clock-name %s.\n", 534 fdt_strerror(err)); 535 break; 536 } 537 538 err = fdt_fixup_phy_connection(blob, nodeoff, 539 PHY_INTERFACE_MODE_RMII); 540 541 if (err < 0) { 542 printf("WARNING: could not set phy-connection-type " 543 "%s.\n", fdt_strerror(err)); 544 break; 545 } 546 547 index = fdt_getprop(blob, nodeoff, "cell-index", 0); 548 if (index == NULL) { 549 printf("WARNING: could not get cell-index of ucc\n"); 550 break; 551 } 552 553 ph = fdt_getprop(blob, nodeoff, "phy-handle", 0); 554 if (ph == NULL) { 555 printf("WARNING: could not get phy-handle of ucc\n"); 556 break; 557 } 558 559 off = fdt_node_offset_by_phandle(blob, *ph); 560 if (off < 0) { 561 printf("WARNING: could not get phy node %s.\n", 562 fdt_strerror(err)); 563 break; 564 } 565 566 val = 0x7 + *index; /* RMII phy address starts from 0x8 */ 567 568 err = fdt_setprop(blob, off, "reg", &val, sizeof(u32)); 569 if (err < 0) { 570 printf("WARNING: could not set reg for phy-handle " 571 "%s.\n", fdt_strerror(err)); 572 break; 573 } 574 } 575 #endif 576 ft_cpu_setup(blob, bd); 577 578 FT_FSL_PCI_SETUP; 579 580 fdt_board_fixup_esdhc(blob, bd); 581 fdt_board_fixup_qe_uart(blob, bd); 582 fdt_board_fixup_qe_usb(blob, bd); 583 584 return 0; 585 } 586 #endif 587