1 /* 2 * Copyright 2007,2009-2011 Freescale Semiconductor, Inc. 3 * 4 * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <pci.h> 11 #include <asm/processor.h> 12 #include <asm/mmu.h> 13 #include <asm/immap_85xx.h> 14 #include <asm/fsl_pci.h> 15 #include <fsl_ddr_sdram.h> 16 #include <asm/fsl_serdes.h> 17 #include <spd_sdram.h> 18 #include <i2c.h> 19 #include <ioports.h> 20 #include <libfdt.h> 21 #include <fdt_support.h> 22 23 #include "bcsr.h" 24 25 const qe_iop_conf_t qe_iop_conf_tab[] = { 26 /* GETH1 */ 27 {4, 10, 1, 0, 2}, /* TxD0 */ 28 {4, 9, 1, 0, 2}, /* TxD1 */ 29 {4, 8, 1, 0, 2}, /* TxD2 */ 30 {4, 7, 1, 0, 2}, /* TxD3 */ 31 {4, 23, 1, 0, 2}, /* TxD4 */ 32 {4, 22, 1, 0, 2}, /* TxD5 */ 33 {4, 21, 1, 0, 2}, /* TxD6 */ 34 {4, 20, 1, 0, 2}, /* TxD7 */ 35 {4, 15, 2, 0, 2}, /* RxD0 */ 36 {4, 14, 2, 0, 2}, /* RxD1 */ 37 {4, 13, 2, 0, 2}, /* RxD2 */ 38 {4, 12, 2, 0, 2}, /* RxD3 */ 39 {4, 29, 2, 0, 2}, /* RxD4 */ 40 {4, 28, 2, 0, 2}, /* RxD5 */ 41 {4, 27, 2, 0, 2}, /* RxD6 */ 42 {4, 26, 2, 0, 2}, /* RxD7 */ 43 {4, 11, 1, 0, 2}, /* TX_EN */ 44 {4, 24, 1, 0, 2}, /* TX_ER */ 45 {4, 16, 2, 0, 2}, /* RX_DV */ 46 {4, 30, 2, 0, 2}, /* RX_ER */ 47 {4, 17, 2, 0, 2}, /* RX_CLK */ 48 {4, 19, 1, 0, 2}, /* GTX_CLK */ 49 {1, 31, 2, 0, 3}, /* GTX125 */ 50 51 /* GETH2 */ 52 {5, 10, 1, 0, 2}, /* TxD0 */ 53 {5, 9, 1, 0, 2}, /* TxD1 */ 54 {5, 8, 1, 0, 2}, /* TxD2 */ 55 {5, 7, 1, 0, 2}, /* TxD3 */ 56 {5, 23, 1, 0, 2}, /* TxD4 */ 57 {5, 22, 1, 0, 2}, /* TxD5 */ 58 {5, 21, 1, 0, 2}, /* TxD6 */ 59 {5, 20, 1, 0, 2}, /* TxD7 */ 60 {5, 15, 2, 0, 2}, /* RxD0 */ 61 {5, 14, 2, 0, 2}, /* RxD1 */ 62 {5, 13, 2, 0, 2}, /* RxD2 */ 63 {5, 12, 2, 0, 2}, /* RxD3 */ 64 {5, 29, 2, 0, 2}, /* RxD4 */ 65 {5, 28, 2, 0, 2}, /* RxD5 */ 66 {5, 27, 2, 0, 3}, /* RxD6 */ 67 {5, 26, 2, 0, 2}, /* RxD7 */ 68 {5, 11, 1, 0, 2}, /* TX_EN */ 69 {5, 24, 1, 0, 2}, /* TX_ER */ 70 {5, 16, 2, 0, 2}, /* RX_DV */ 71 {5, 30, 2, 0, 2}, /* RX_ER */ 72 {5, 17, 2, 0, 2}, /* RX_CLK */ 73 {5, 19, 1, 0, 2}, /* GTX_CLK */ 74 {1, 31, 2, 0, 3}, /* GTX125 */ 75 {4, 6, 3, 0, 2}, /* MDIO */ 76 {4, 5, 1, 0, 2}, /* MDC */ 77 78 /* UART1 */ 79 {2, 0, 1, 0, 2}, /* UART_SOUT1 */ 80 {2, 1, 1, 0, 2}, /* UART_RTS1 */ 81 {2, 2, 2, 0, 2}, /* UART_CTS1 */ 82 {2, 3, 2, 0, 2}, /* UART_SIN1 */ 83 84 {0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */ 85 }; 86 87 void local_bus_init(void); 88 89 int board_early_init_f (void) 90 { 91 /* 92 * Initialize local bus. 93 */ 94 local_bus_init (); 95 96 enable_8568mds_duart(); 97 enable_8568mds_flash_write(); 98 #if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2) 99 reset_8568mds_uccs(); 100 #endif 101 #if defined(CONFIG_QE) && !defined(CONFIG_eTSEC_MDIO_BUS) 102 enable_8568mds_qe_mdio(); 103 #endif 104 105 #ifdef CONFIG_SYS_I2C2_OFFSET 106 /* Enable I2C2_SCL and I2C2_SDA */ 107 volatile struct par_io *port_c; 108 port_c = (struct par_io*)(CONFIG_SYS_IMMR + 0xe0140); 109 port_c->cpdir2 |= 0x0f000000; 110 port_c->cppar2 &= ~0x0f000000; 111 port_c->cppar2 |= 0x0a000000; 112 #endif 113 114 return 0; 115 } 116 117 int checkboard (void) 118 { 119 printf ("Board: 8568 MDS\n"); 120 121 return 0; 122 } 123 124 /* 125 * Initialize Local Bus 126 */ 127 void 128 local_bus_init(void) 129 { 130 volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 131 volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; 132 133 uint clkdiv; 134 sys_info_t sysinfo; 135 136 get_sys_info(&sysinfo); 137 clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; 138 139 gur->lbiuiplldcr1 = 0x00078080; 140 if (clkdiv == 16) { 141 gur->lbiuiplldcr0 = 0x7c0f1bf0; 142 } else if (clkdiv == 8) { 143 gur->lbiuiplldcr0 = 0x6c0f1bf0; 144 } else if (clkdiv == 4) { 145 gur->lbiuiplldcr0 = 0x5c0f1bf0; 146 } 147 148 lbc->lcrr |= 0x00030000; 149 150 asm("sync;isync;msync"); 151 } 152 153 /* 154 * Initialize SDRAM memory on the Local Bus. 155 */ 156 void lbc_sdram_init(void) 157 { 158 #if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM) 159 160 uint idx; 161 volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; 162 uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE; 163 uint lsdmr_common; 164 165 puts("LBC SDRAM: "); 166 print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, 167 "\n "); 168 169 /* 170 * Setup SDRAM Base and Option Registers 171 */ 172 set_lbc_or(2, CONFIG_SYS_OR2_PRELIM); 173 set_lbc_br(2, CONFIG_SYS_BR2_PRELIM); 174 asm("msync"); 175 176 lbc->lbcr = CONFIG_SYS_LBC_LBCR; 177 asm("msync"); 178 179 lbc->lsrt = CONFIG_SYS_LBC_LSRT; 180 lbc->mrtpr = CONFIG_SYS_LBC_MRTPR; 181 asm("msync"); 182 183 /* 184 * MPC8568 uses "new" 15-16 style addressing. 185 */ 186 lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON; 187 lsdmr_common |= LSDMR_BSMA1516; 188 189 /* 190 * Issue PRECHARGE ALL command. 191 */ 192 lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL; 193 asm("sync;msync"); 194 *sdram_addr = 0xff; 195 ppcDcbf((unsigned long) sdram_addr); 196 udelay(100); 197 198 /* 199 * Issue 8 AUTO REFRESH commands. 200 */ 201 for (idx = 0; idx < 8; idx++) { 202 lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH; 203 asm("sync;msync"); 204 *sdram_addr = 0xff; 205 ppcDcbf((unsigned long) sdram_addr); 206 udelay(100); 207 } 208 209 /* 210 * Issue 8 MODE-set command. 211 */ 212 lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW; 213 asm("sync;msync"); 214 *sdram_addr = 0xff; 215 ppcDcbf((unsigned long) sdram_addr); 216 udelay(100); 217 218 /* 219 * Issue NORMAL OP command. 220 */ 221 lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL; 222 asm("sync;msync"); 223 *sdram_addr = 0xff; 224 ppcDcbf((unsigned long) sdram_addr); 225 udelay(200); /* Overkill. Must wait > 200 bus cycles */ 226 227 #endif /* enable SDRAM init */ 228 } 229 230 #if defined(CONFIG_PCI) 231 #ifndef CONFIG_PCI_PNP 232 static struct pci_config_table pci_mpc8568mds_config_table[] = { 233 { 234 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 235 pci_cfgfunc_config_device, 236 {PCI_ENET0_IOADDR, 237 PCI_ENET0_MEMADDR, 238 PCI_COMMON_MEMORY | PCI_COMMAND_MASTER} 239 }, 240 {} 241 }; 242 #endif 243 244 static struct pci_controller pci1_hose; 245 #endif /* CONFIG_PCI */ 246 247 /* 248 * pib_init() -- Initialize the PCA9555 IO expander on the PIB board 249 */ 250 void 251 pib_init(void) 252 { 253 u8 val8, orig_i2c_bus; 254 /* 255 * Assign PIB PMC2/3 to PCI bus 256 */ 257 258 /*switch temporarily to I2C bus #2 */ 259 orig_i2c_bus = i2c_get_bus_num(); 260 i2c_set_bus_num(1); 261 262 val8 = 0x00; 263 i2c_write(0x23, 0x6, 1, &val8, 1); 264 i2c_write(0x23, 0x7, 1, &val8, 1); 265 val8 = 0xff; 266 i2c_write(0x23, 0x2, 1, &val8, 1); 267 i2c_write(0x23, 0x3, 1, &val8, 1); 268 269 val8 = 0x00; 270 i2c_write(0x26, 0x6, 1, &val8, 1); 271 val8 = 0x34; 272 i2c_write(0x26, 0x7, 1, &val8, 1); 273 val8 = 0xf9; 274 i2c_write(0x26, 0x2, 1, &val8, 1); 275 val8 = 0xff; 276 i2c_write(0x26, 0x3, 1, &val8, 1); 277 278 val8 = 0x00; 279 i2c_write(0x27, 0x6, 1, &val8, 1); 280 i2c_write(0x27, 0x7, 1, &val8, 1); 281 val8 = 0xff; 282 i2c_write(0x27, 0x2, 1, &val8, 1); 283 val8 = 0xef; 284 i2c_write(0x27, 0x3, 1, &val8, 1); 285 286 asm("eieio"); 287 i2c_set_bus_num(orig_i2c_bus); 288 } 289 290 #ifdef CONFIG_PCI 291 void pci_init_board(void) 292 { 293 volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 294 int first_free_busno = 0; 295 #ifdef CONFIG_PCI1 296 struct fsl_pci_info pci_info; 297 u32 devdisr, pordevsr, io_sel; 298 u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel; 299 300 devdisr = in_be32(&gur->devdisr); 301 pordevsr = in_be32(&gur->pordevsr); 302 porpllsr = in_be32(&gur->porpllsr); 303 io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19; 304 305 debug (" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel); 306 307 pci_speed = 66666000; 308 pci_32 = 1; 309 pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; 310 pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; 311 312 if (!(devdisr & MPC85xx_DEVDISR_PCI1)) { 313 SET_STD_PCI_INFO(pci_info, 1); 314 set_next_law(pci_info.mem_phys, 315 law_size_bits(pci_info.mem_size), pci_info.law); 316 set_next_law(pci_info.io_phys, 317 law_size_bits(pci_info.io_size), pci_info.law); 318 319 pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs); 320 printf("PCI: %d bit, %s MHz, %s, %s, %s (base address %lx)\n", 321 (pci_32) ? 32 : 64, 322 (pci_speed == 33333000) ? "33" : 323 (pci_speed == 66666000) ? "66" : "unknown", 324 pci_clk_sel ? "sync" : "async", 325 pci_agent ? "agent" : "host", 326 pci_arb ? "arbiter" : "external-arbiter", 327 pci_info.regs); 328 329 #ifndef CONFIG_PCI_PNP 330 pci1_hose.config_table = pci_mpc8568mds_config_table; 331 #endif 332 first_free_busno = fsl_pci_init_port(&pci_info, 333 &pci1_hose, first_free_busno); 334 } else { 335 printf("PCI: disabled\n"); 336 } 337 338 puts("\n"); 339 #else 340 setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */ 341 #endif 342 343 fsl_pcie_init_board(first_free_busno); 344 } 345 #endif /* CONFIG_PCI */ 346 347 #if defined(CONFIG_OF_BOARD_SETUP) 348 void ft_board_setup(void *blob, bd_t *bd) 349 { 350 ft_cpu_setup(blob, bd); 351 352 FT_FSL_PCI_SETUP; 353 } 354 #endif 355