1 /*
2  * Copyright (C) 2007,2010 Freescale Semiconductor, Inc.
3  * Dave Liu <daveliu@freescale.com>
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 #include <common.h>
9 #include <hwconfig.h>
10 #include <i2c.h>
11 #include <asm/io.h>
12 #include <asm/fsl_mpc83xx_serdes.h>
13 #include <spd_sdram.h>
14 #include <tsec.h>
15 #include <libfdt.h>
16 #include <fdt_support.h>
17 #include <fsl_esdhc.h>
18 #include <fsl_mdio.h>
19 #include <phy.h>
20 #include "pci.h"
21 #include "../common/pq-mds-pib.h"
22 
23 DECLARE_GLOBAL_DATA_PTR;
24 
25 int board_early_init_f(void)
26 {
27 	u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
28 
29 	/* Enable flash write */
30 	bcsr[0x9] &= ~0x04;
31 	/* Clear all of the interrupt of BCSR */
32 	bcsr[0xe] = 0xff;
33 
34 #ifdef CONFIG_FSL_SERDES
35 	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
36 	u32 spridr = in_be32(&immr->sysconf.spridr);
37 
38 	/* we check only part num, and don't look for CPU revisions */
39 	switch (PARTID_NO_E(spridr)) {
40 	case SPR_8377:
41 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
42 				FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
43 		break;
44 	case SPR_8378:
45 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII,
46 				FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V);
47 		break;
48 	case SPR_8379:
49 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
50 				FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
51 		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_SATA,
52 				FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
53 		break;
54 	default:
55 		printf("serdes not configured: unknown CPU part number: "
56 				"%04x\n", spridr >> 16);
57 		break;
58 	}
59 #endif /* CONFIG_FSL_SERDES */
60 	return 0;
61 }
62 
63 #ifdef CONFIG_FSL_ESDHC
64 int board_mmc_init(bd_t *bd)
65 {
66 	struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
67 	u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
68 
69 	if (!hwconfig("esdhc"))
70 		return 0;
71 
72 	/* Set SPI_SD, SER_SD, and IRQ4_WP so that SD signals go through */
73 	bcsr[0xc] |= 0x4c;
74 
75 	/* Set proper bits in SICR to allow SD signals through */
76 	clrsetbits_be32(&im->sysconf.sicrl, SICRL_USB_B, SICRL_USB_B_SD);
77 	clrsetbits_be32(&im->sysconf.sicrh, SICRH_GPIO2_E | SICRH_SPI,
78 			SICRH_GPIO2_E_SD | SICRH_SPI_SD);
79 
80 	return fsl_esdhc_mmc_init(bd);
81 }
82 #endif
83 
84 #if defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2)
85 int board_eth_init(bd_t *bd)
86 {
87 	struct fsl_pq_mdio_info mdio_info;
88 	struct tsec_info_struct tsec_info[2];
89 	struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
90 	u32 rcwh = in_be32(&im->reset.rcwh);
91 	u32 tsec_mode;
92 	int num = 0;
93 
94 	/* New line after Net: */
95 	printf("\n");
96 
97 #ifdef CONFIG_TSEC1
98 	SET_STD_TSEC_INFO(tsec_info[num], 1);
99 
100 	printf(CONFIG_TSEC1_NAME ": ");
101 
102 	tsec_mode = rcwh & HRCWH_TSEC1M_MASK;
103 	if (tsec_mode == HRCWH_TSEC1M_IN_RGMII) {
104 		printf("RGMII\n");
105 		/* this is default, no need to fixup */
106 	} else if (tsec_mode == HRCWH_TSEC1M_IN_SGMII) {
107 		printf("SGMII\n");
108 		tsec_info[num].phyaddr = TSEC1_PHY_ADDR_SGMII;
109 		tsec_info[num].flags = TSEC_GIGABIT;
110 	} else {
111 		printf("unsupported PHY type\n");
112 	}
113 	num++;
114 #endif
115 #ifdef CONFIG_TSEC2
116 	SET_STD_TSEC_INFO(tsec_info[num], 2);
117 
118 	printf(CONFIG_TSEC2_NAME ": ");
119 
120 	tsec_mode = rcwh & HRCWH_TSEC2M_MASK;
121 	if (tsec_mode == HRCWH_TSEC2M_IN_RGMII) {
122 		printf("RGMII\n");
123 		/* this is default, no need to fixup */
124 	} else if (tsec_mode == HRCWH_TSEC2M_IN_SGMII) {
125 		printf("SGMII\n");
126 		tsec_info[num].phyaddr = TSEC2_PHY_ADDR_SGMII;
127 		tsec_info[num].flags = TSEC_GIGABIT;
128 	} else {
129 		printf("unsupported PHY type\n");
130 	}
131 	num++;
132 #endif
133 
134 	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
135 	mdio_info.name = DEFAULT_MII_NAME;
136 	fsl_pq_mdio_init(bd, &mdio_info);
137 
138 	return tsec_eth_init(bd, tsec_info, num);
139 }
140 
141 static void __ft_tsec_fixup(void *blob, bd_t *bd, const char *alias,
142 			    int phy_addr)
143 {
144 	const u32 *ph;
145 	int off;
146 	int err;
147 
148 	off = fdt_path_offset(blob, alias);
149 	if (off < 0) {
150 		printf("WARNING: could not find %s alias: %s.\n", alias,
151 			fdt_strerror(off));
152 		return;
153 	}
154 
155 	err = fdt_fixup_phy_connection(blob, off, PHY_INTERFACE_MODE_SGMII);
156 
157 	if (err) {
158 		printf("WARNING: could not set phy-connection-type for %s: "
159 			"%s.\n", alias, fdt_strerror(err));
160 		return;
161 	}
162 
163 	ph = (u32 *)fdt_getprop(blob, off, "phy-handle", 0);
164 	if (!ph) {
165 		printf("WARNING: could not get phy-handle for %s.\n",
166 			alias);
167 		return;
168 	}
169 
170 	off = fdt_node_offset_by_phandle(blob, *ph);
171 	if (off < 0) {
172 		printf("WARNING: could not get phy node for %s: %s\n", alias,
173 			fdt_strerror(off));
174 		return;
175 	}
176 
177 	phy_addr = cpu_to_fdt32(phy_addr);
178 	err = fdt_setprop(blob, off, "reg", &phy_addr, sizeof(phy_addr));
179 	if (err < 0) {
180 		printf("WARNING: could not set phy node's reg for %s: "
181 			"%s.\n", alias, fdt_strerror(err));
182 		return;
183 	}
184 }
185 
186 static void ft_tsec_fixup(void *blob, bd_t *bd)
187 {
188 	struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
189 	u32 rcwh = in_be32(&im->reset.rcwh);
190 	u32 tsec_mode;
191 
192 #ifdef CONFIG_TSEC1
193 	tsec_mode = rcwh & HRCWH_TSEC1M_MASK;
194 	if (tsec_mode == HRCWH_TSEC1M_IN_SGMII)
195 		__ft_tsec_fixup(blob, bd, "ethernet0", TSEC1_PHY_ADDR_SGMII);
196 #endif
197 
198 #ifdef CONFIG_TSEC2
199 	tsec_mode = rcwh & HRCWH_TSEC2M_MASK;
200 	if (tsec_mode == HRCWH_TSEC2M_IN_SGMII)
201 		__ft_tsec_fixup(blob, bd, "ethernet1", TSEC2_PHY_ADDR_SGMII);
202 #endif
203 }
204 #else
205 static inline void ft_tsec_fixup(void *blob, bd_t *bd) {}
206 #endif /* defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2) */
207 
208 int board_early_init_r(void)
209 {
210 #ifdef CONFIG_PQ_MDS_PIB
211 	pib_init();
212 #endif
213 	return 0;
214 }
215 
216 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
217 extern void ddr_enable_ecc(unsigned int dram_size);
218 #endif
219 int fixed_sdram(void);
220 
221 int initdram(void)
222 {
223 	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
224 	u32 msize = 0;
225 
226 	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
227 		return -ENXIO;
228 
229 #if defined(CONFIG_SPD_EEPROM)
230 	msize = spd_sdram();
231 #else
232 	msize = fixed_sdram();
233 #endif
234 
235 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
236 	/* Initialize DDR ECC byte */
237 	ddr_enable_ecc(msize * 1024 * 1024);
238 #endif
239 
240 	/* return total bus DDR size(bytes) */
241 	gd->ram_size = msize * 1024 * 1024;
242 
243 	return 0;
244 }
245 
246 #if !defined(CONFIG_SPD_EEPROM)
247 /*************************************************************************
248  *  fixed sdram init -- doesn't use serial presence detect.
249  ************************************************************************/
250 int fixed_sdram(void)
251 {
252 	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
253 	u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
254 	u32 msize_log2 = __ilog2(msize);
255 
256 	im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
257 	im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
258 
259 #if (CONFIG_SYS_DDR_SIZE != 512)
260 #warning Currenly any ddr size other than 512 is not supported
261 #endif
262 	im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE;
263 	udelay(50000);
264 
265 	im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL;
266 	udelay(1000);
267 
268 	im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
269 	im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
270 	udelay(1000);
271 
272 	im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
273 	im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
274 	im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
275 	im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
276 	im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
277 	im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
278 	im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
279 	im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
280 	im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
281 	__asm__ __volatile__("sync");
282 	udelay(1000);
283 
284 	im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
285 	udelay(2000);
286 	return CONFIG_SYS_DDR_SIZE;
287 }
288 #endif /*!CONFIG_SYS_SPD_EEPROM */
289 
290 int checkboard(void)
291 {
292 	puts("Board: Freescale MPC837xEMDS\n");
293 	return 0;
294 }
295 
296 #ifdef CONFIG_PCI
297 int board_pci_host_broken(void)
298 {
299 	struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
300 	const u32 rcw_mask = HRCWH_PCI1_ARBITER_ENABLE | HRCWH_PCI_HOST;
301 
302 	/* It's always OK in case of external arbiter. */
303 	if (hwconfig_subarg_cmp("pci", "arbiter", "external"))
304 		return 0;
305 
306 	if ((in_be32(&im->reset.rcwh) & rcw_mask) != rcw_mask)
307 		return 1;
308 
309 	return 0;
310 }
311 
312 static void ft_pci_fixup(void *blob, bd_t *bd)
313 {
314 	const char *status = "broken (no arbiter)";
315 	int off;
316 	int err;
317 
318 	off = fdt_path_offset(blob, "pci0");
319 	if (off < 0) {
320 		printf("WARNING: could not find pci0 alias: %s.\n",
321 			fdt_strerror(off));
322 		return;
323 	}
324 
325 	err = fdt_setprop(blob, off, "status", status, strlen(status) + 1);
326 	if (err) {
327 		printf("WARNING: could not set status for pci0: %s.\n",
328 			fdt_strerror(err));
329 		return;
330 	}
331 }
332 #endif
333 
334 #if defined(CONFIG_OF_BOARD_SETUP)
335 int ft_board_setup(void *blob, bd_t *bd)
336 {
337 	ft_cpu_setup(blob, bd);
338 	ft_tsec_fixup(blob, bd);
339 	fsl_fdt_fixup_dr_usb(blob, bd);
340 	fdt_fixup_esdhc(blob, bd);
341 #ifdef CONFIG_PCI
342 	ft_pci_setup(blob, bd);
343 	if (board_pci_host_broken())
344 		ft_pci_fixup(blob, bd);
345 	ft_pcie_fixup(blob, bd);
346 #endif
347 
348 	return 0;
349 }
350 #endif /* CONFIG_OF_BOARD_SETUP */
351