1 /*
2  * Copyright 2015 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #include <common.h>
8 #include <fsl_ddr_sdram.h>
9 #include <fsl_ddr_dimm_params.h>
10 #include <asm/arch/soc.h>
11 #include <asm/arch/clock.h>
12 #include "ddr.h"
13 
14 DECLARE_GLOBAL_DATA_PTR;
15 
16 void fsl_ddr_board_options(memctl_options_t *popts,
17 				dimm_params_t *pdimm,
18 				unsigned int ctrl_num)
19 {
20 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
21 	u8 dq_mapping_0, dq_mapping_2, dq_mapping_3;
22 #endif
23 	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
24 	ulong ddr_freq;
25 	int slot;
26 
27 	if (ctrl_num > 2) {
28 		printf("Not supported controller number %d\n", ctrl_num);
29 		return;
30 	}
31 
32 	for (slot = 0; slot < CONFIG_DIMM_SLOTS_PER_CTLR; slot++) {
33 		if (pdimm[slot].n_ranks)
34 			break;
35 	}
36 
37 	if (slot >= CONFIG_DIMM_SLOTS_PER_CTLR)
38 		return;
39 
40 	/*
41 	 * we use identical timing for all slots. If needed, change the code
42 	 * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
43 	 */
44 	if (popts->registered_dimm_en)
45 		pbsp = rdimms[ctrl_num];
46 	else
47 		pbsp = udimms[ctrl_num];
48 
49 
50 	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
51 	 * freqency and n_banks specified in board_specific_parameters table.
52 	 */
53 	ddr_freq = get_ddr_freq(ctrl_num) / 1000000;
54 	while (pbsp->datarate_mhz_high) {
55 		if (pbsp->n_ranks == pdimm[slot].n_ranks &&
56 		    (pdimm[slot].rank_density >> 30) >= pbsp->rank_gb) {
57 			if (ddr_freq <= pbsp->datarate_mhz_high) {
58 				popts->clk_adjust = pbsp->clk_adjust;
59 				popts->wrlvl_start = pbsp->wrlvl_start;
60 				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
61 				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
62 				goto found;
63 			}
64 			pbsp_highest = pbsp;
65 		}
66 		pbsp++;
67 	}
68 
69 	if (pbsp_highest) {
70 		printf("Error: board specific timing not found for data rate %lu MT/s\n"
71 			"Trying to use the highest speed (%u) parameters\n",
72 			ddr_freq, pbsp_highest->datarate_mhz_high);
73 		popts->clk_adjust = pbsp_highest->clk_adjust;
74 		popts->wrlvl_start = pbsp_highest->wrlvl_start;
75 		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
76 		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
77 	} else {
78 		panic("DIMM is not supported by this board");
79 	}
80 found:
81 	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
82 		"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
83 		pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
84 		pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
85 		pbsp->wrlvl_ctl_3);
86 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
87 	if (ctrl_num == CONFIG_DP_DDR_CTRL) {
88 		if (popts->registered_dimm_en)
89 			printf("WARN: RDIMM not supported.\n");
90 		/* force DDR bus width to 32 bits */
91 		popts->data_bus_width = 1;
92 		popts->otf_burst_chop_en = 0;
93 		popts->burst_length = DDR_BL8;
94 		popts->bstopre = 0;	/* enable auto precharge */
95 		/*
96 		 * Layout optimization results byte mapping
97 		 * Byte 0 -> Byte ECC
98 		 * Byte 1 -> Byte 3
99 		 * Byte 2 -> Byte 2
100 		 * Byte 3 -> Byte 1
101 		 * Byte ECC -> Byte 0
102 		 */
103 		dq_mapping_0 = pdimm[slot].dq_mapping[0];
104 		dq_mapping_2 = pdimm[slot].dq_mapping[2];
105 		dq_mapping_3 = pdimm[slot].dq_mapping[3];
106 		pdimm[slot].dq_mapping[0] = pdimm[slot].dq_mapping[8];
107 		pdimm[slot].dq_mapping[1] = pdimm[slot].dq_mapping[9];
108 		pdimm[slot].dq_mapping[2] = pdimm[slot].dq_mapping[6];
109 		pdimm[slot].dq_mapping[3] = pdimm[slot].dq_mapping[7];
110 		pdimm[slot].dq_mapping[6] = dq_mapping_2;
111 		pdimm[slot].dq_mapping[7] = dq_mapping_3;
112 		pdimm[slot].dq_mapping[8] = dq_mapping_0;
113 		pdimm[slot].dq_mapping[9] = 0;
114 		pdimm[slot].dq_mapping[10] = 0;
115 		pdimm[slot].dq_mapping[11] = 0;
116 		pdimm[slot].dq_mapping[12] = 0;
117 		pdimm[slot].dq_mapping[13] = 0;
118 		pdimm[slot].dq_mapping[14] = 0;
119 		pdimm[slot].dq_mapping[15] = 0;
120 		pdimm[slot].dq_mapping[16] = 0;
121 		pdimm[slot].dq_mapping[17] = 0;
122 	}
123 #endif
124 	/* To work at higher than 1333MT/s */
125 	popts->half_strength_driver_enable = 0;
126 	/*
127 	 * Write leveling override
128 	 */
129 	popts->wrlvl_override = 1;
130 	popts->wrlvl_sample = 0x0;	/* 32 clocks */
131 
132 	/*
133 	 * Rtt and Rtt_WR override
134 	 */
135 	popts->rtt_override = 0;
136 
137 	/* Enable ZQ calibration */
138 	popts->zq_en = 1;
139 
140 	/* optimize cpo for erratum A-009942 */
141 	popts->cpo_sample = 0x6e;
142 
143 	if (ddr_freq < 2350) {
144 		if (pdimm[0].n_ranks == 2 && pdimm[1].n_ranks == 2) {
145 			/* four chip-selects */
146 			popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
147 					  DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
148 			popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm);
149 			popts->twot_en = 1;	/* enable 2T timing */
150 		} else {
151 			popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
152 					  DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
153 			popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
154 					  DDR_CDR2_VREF_RANGE_2;
155 		}
156 	} else {
157 		popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
158 				  DDR_CDR1_ODT(DDR_CDR_ODT_100ohm);
159 		popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_100ohm) |
160 				  DDR_CDR2_VREF_RANGE_2;
161 	}
162 }
163 
164 int fsl_initdram(void)
165 {
166 #if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
167 	gd->ram_size = fsl_ddr_sdram_size();
168 #else
169 	puts("Initializing DDR....using SPD\n");
170 
171 	gd->ram_size = fsl_ddr_sdram();
172 #endif
173 
174 	return 0;
175 }
176