1 /* 2 * Copyright 2016 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <i2c.h> 9 #include <fdt_support.h> 10 #include <fsl_ddr_sdram.h> 11 #include <asm/io.h> 12 #include <asm/arch/clock.h> 13 #include <asm/arch/fsl_serdes.h> 14 #include <asm/arch/ppa.h> 15 #include <asm/arch/fdt.h> 16 #include <asm/arch/mmu.h> 17 #include <asm/arch/soc.h> 18 #include <ahci.h> 19 #include <hwconfig.h> 20 #include <mmc.h> 21 #include <scsi.h> 22 #include <fm_eth.h> 23 #include <fsl_csu.h> 24 #include <fsl_esdhc.h> 25 #include <fsl_ifc.h> 26 #include <fsl_sec.h> 27 #include <spl.h> 28 29 #include "../common/vid.h" 30 #include "../common/qixis.h" 31 #include "ls1046aqds_qixis.h" 32 33 DECLARE_GLOBAL_DATA_PTR; 34 35 enum { 36 MUX_TYPE_GPIO, 37 }; 38 39 int checkboard(void) 40 { 41 char buf[64]; 42 #ifndef CONFIG_SD_BOOT 43 u8 sw; 44 #endif 45 46 puts("Board: LS1046AQDS, boot from "); 47 48 #ifdef CONFIG_SD_BOOT 49 puts("SD\n"); 50 #else 51 sw = QIXIS_READ(brdcfg[0]); 52 sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; 53 54 if (sw < 0x8) 55 printf("vBank: %d\n", sw); 56 else if (sw == 0x8) 57 puts("PromJet\n"); 58 else if (sw == 0x9) 59 puts("NAND\n"); 60 else if (sw == 0xF) 61 printf("QSPI\n"); 62 else 63 printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); 64 #endif 65 66 printf("Sys ID: 0x%02x, Sys Ver: 0x%02x\n", 67 QIXIS_READ(id), QIXIS_READ(arch)); 68 69 printf("FPGA: v%d (%s), build %d\n", 70 (int)QIXIS_READ(scver), qixis_read_tag(buf), 71 (int)qixis_read_minor()); 72 73 return 0; 74 } 75 76 bool if_board_diff_clk(void) 77 { 78 u8 diff_conf = QIXIS_READ(brdcfg[11]); 79 80 return diff_conf & 0x40; 81 } 82 83 unsigned long get_board_sys_clk(void) 84 { 85 u8 sysclk_conf = QIXIS_READ(brdcfg[1]); 86 87 switch (sysclk_conf & 0x0f) { 88 case QIXIS_SYSCLK_64: 89 return 64000000; 90 case QIXIS_SYSCLK_83: 91 return 83333333; 92 case QIXIS_SYSCLK_100: 93 return 100000000; 94 case QIXIS_SYSCLK_125: 95 return 125000000; 96 case QIXIS_SYSCLK_133: 97 return 133333333; 98 case QIXIS_SYSCLK_150: 99 return 150000000; 100 case QIXIS_SYSCLK_160: 101 return 160000000; 102 case QIXIS_SYSCLK_166: 103 return 166666666; 104 } 105 106 return 66666666; 107 } 108 109 unsigned long get_board_ddr_clk(void) 110 { 111 u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); 112 113 if (if_board_diff_clk()) 114 return get_board_sys_clk(); 115 switch ((ddrclk_conf & 0x30) >> 4) { 116 case QIXIS_DDRCLK_100: 117 return 100000000; 118 case QIXIS_DDRCLK_125: 119 return 125000000; 120 case QIXIS_DDRCLK_133: 121 return 133333333; 122 } 123 124 return 66666666; 125 } 126 127 #ifdef CONFIG_LPUART 128 u32 get_lpuart_clk(void) 129 { 130 return gd->bus_clk; 131 } 132 #endif 133 134 int select_i2c_ch_pca9547(u8 ch) 135 { 136 int ret; 137 138 ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); 139 if (ret) { 140 puts("PCA: failed to select proper channel\n"); 141 return ret; 142 } 143 144 return 0; 145 } 146 147 int dram_init(void) 148 { 149 /* 150 * When resuming from deep sleep, the I2C channel may not be 151 * in the default channel. So, switch to the default channel 152 * before accessing DDR SPD. 153 */ 154 select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); 155 fsl_initdram(); 156 #if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD) 157 /* This will break-before-make MMU for DDR */ 158 update_early_mmu_table(); 159 #endif 160 161 return 0; 162 } 163 164 int i2c_multiplexer_select_vid_channel(u8 channel) 165 { 166 return select_i2c_ch_pca9547(channel); 167 } 168 169 int board_early_init_f(void) 170 { 171 #ifdef CONFIG_HAS_FSL_XHCI_USB 172 struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; 173 u32 usb_pwrfault; 174 #endif 175 #ifdef CONFIG_LPUART 176 u8 uart; 177 #endif 178 179 #ifdef CONFIG_SYS_I2C_EARLY_INIT 180 i2c_early_init_f(); 181 #endif 182 fsl_lsch2_early_init_f(); 183 184 #ifdef CONFIG_HAS_FSL_XHCI_USB 185 out_be32(&scfg->rcwpmuxcr0, 0x3333); 186 out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1); 187 usb_pwrfault = (SCFG_USBPWRFAULT_DEDICATED << 188 SCFG_USBPWRFAULT_USB3_SHIFT) | 189 (SCFG_USBPWRFAULT_DEDICATED << 190 SCFG_USBPWRFAULT_USB2_SHIFT) | 191 (SCFG_USBPWRFAULT_SHARED << 192 SCFG_USBPWRFAULT_USB1_SHIFT); 193 out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault); 194 #endif 195 196 #ifdef CONFIG_LPUART 197 /* We use lpuart0 as system console */ 198 uart = QIXIS_READ(brdcfg[14]); 199 uart &= ~CFG_UART_MUX_MASK; 200 uart |= CFG_LPUART_EN << CFG_UART_MUX_SHIFT; 201 QIXIS_WRITE(brdcfg[14], uart); 202 #endif 203 204 return 0; 205 } 206 207 #ifdef CONFIG_FSL_DEEP_SLEEP 208 /* determine if it is a warm boot */ 209 bool is_warm_boot(void) 210 { 211 #define DCFG_CCSR_CRSTSR_WDRFR (1 << 3) 212 struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR; 213 214 if (in_be32(&gur->crstsr) & DCFG_CCSR_CRSTSR_WDRFR) 215 return 1; 216 217 return 0; 218 } 219 #endif 220 221 int config_board_mux(int ctrl_type) 222 { 223 u8 reg14; 224 225 reg14 = QIXIS_READ(brdcfg[14]); 226 227 switch (ctrl_type) { 228 case MUX_TYPE_GPIO: 229 reg14 = (reg14 & (~0x6)) | 0x2; 230 break; 231 default: 232 puts("Unsupported mux interface type\n"); 233 return -1; 234 } 235 236 QIXIS_WRITE(brdcfg[14], reg14); 237 238 return 0; 239 } 240 241 int config_serdes_mux(void) 242 { 243 return 0; 244 } 245 246 #ifdef CONFIG_MISC_INIT_R 247 int misc_init_r(void) 248 { 249 if (hwconfig("gpio")) 250 config_board_mux(MUX_TYPE_GPIO); 251 252 return 0; 253 } 254 #endif 255 256 int board_init(void) 257 { 258 select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); 259 260 #ifdef CONFIG_SYS_FSL_SERDES 261 config_serdes_mux(); 262 #endif 263 264 if (adjust_vdd(0)) 265 printf("Warning: Adjusting core voltage failed.\n"); 266 267 #ifdef CONFIG_FSL_LS_PPA 268 ppa_init(); 269 #endif 270 271 #ifdef CONFIG_SECURE_BOOT 272 /* 273 * In case of Secure Boot, the IBR configures the SMMU 274 * to allow only Secure transactions. 275 * SMMU must be reset in bypass mode. 276 * Set the ClientPD bit and Clear the USFCFG Bit 277 */ 278 u32 val; 279 val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK); 280 out_le32(SMMU_SCR0, val); 281 val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK); 282 out_le32(SMMU_NSCR0, val); 283 #endif 284 285 #ifdef CONFIG_FSL_CAAM 286 sec_init(); 287 #endif 288 289 return 0; 290 } 291 292 #ifdef CONFIG_OF_BOARD_SETUP 293 int ft_board_setup(void *blob, bd_t *bd) 294 { 295 u64 base[CONFIG_NR_DRAM_BANKS]; 296 u64 size[CONFIG_NR_DRAM_BANKS]; 297 u8 reg; 298 299 /* fixup DT for the two DDR banks */ 300 base[0] = gd->bd->bi_dram[0].start; 301 size[0] = gd->bd->bi_dram[0].size; 302 base[1] = gd->bd->bi_dram[1].start; 303 size[1] = gd->bd->bi_dram[1].size; 304 305 fdt_fixup_memory_banks(blob, base, size, 2); 306 ft_cpu_setup(blob, bd); 307 308 #ifdef CONFIG_SYS_DPAA_FMAN 309 fdt_fixup_fman_ethernet(blob); 310 fdt_fixup_board_enet(blob); 311 #endif 312 313 reg = QIXIS_READ(brdcfg[0]); 314 reg = (reg & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; 315 316 /* Disable IFC if QSPI is enabled */ 317 if (reg == 0xF) 318 do_fixup_by_compat(blob, "fsl,ifc", 319 "status", "disabled", 8 + 1, 1); 320 321 return 0; 322 } 323 #endif 324 325 u8 flash_read8(void *addr) 326 { 327 return __raw_readb(addr + 1); 328 } 329 330 void flash_write16(u16 val, void *addr) 331 { 332 u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00)); 333 334 __raw_writew(shftval, addr); 335 } 336 337 u16 flash_read16(void *addr) 338 { 339 u16 val = __raw_readw(addr); 340 341 return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00); 342 } 343