1 /* 2 * Copyright 2015 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <fsl_ddr_sdram.h> 9 #include <fsl_ddr_dimm_params.h> 10 #include "ddr.h" 11 #ifdef CONFIG_FSL_DEEP_SLEEP 12 #include <fsl_sleep.h> 13 #endif 14 15 DECLARE_GLOBAL_DATA_PTR; 16 17 void fsl_ddr_board_options(memctl_options_t *popts, 18 dimm_params_t *pdimm, 19 unsigned int ctrl_num) 20 { 21 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; 22 ulong ddr_freq; 23 24 if (ctrl_num > 1) { 25 printf("Not supported controller number %d\n", ctrl_num); 26 return; 27 } 28 if (!pdimm->n_ranks) 29 return; 30 31 pbsp = udimms[0]; 32 33 /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr 34 * freqency and n_banks specified in board_specific_parameters table. 35 */ 36 ddr_freq = get_ddr_freq(0) / 1000000; 37 while (pbsp->datarate_mhz_high) { 38 if (pbsp->n_ranks == pdimm->n_ranks) { 39 if (ddr_freq <= pbsp->datarate_mhz_high) { 40 popts->clk_adjust = pbsp->clk_adjust; 41 popts->wrlvl_start = pbsp->wrlvl_start; 42 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 43 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 44 popts->cpo_override = pbsp->cpo_override; 45 popts->write_data_delay = 46 pbsp->write_data_delay; 47 goto found; 48 } 49 pbsp_highest = pbsp; 50 } 51 pbsp++; 52 } 53 54 if (pbsp_highest) { 55 printf("Error: board specific timing not found for %lu MT/s\n", 56 ddr_freq); 57 printf("Trying to use the highest speed (%u) parameters\n", 58 pbsp_highest->datarate_mhz_high); 59 popts->clk_adjust = pbsp_highest->clk_adjust; 60 popts->wrlvl_start = pbsp_highest->wrlvl_start; 61 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 62 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 63 } else { 64 panic("DIMM is not supported by this board"); 65 } 66 found: 67 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", 68 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); 69 70 /* force DDR bus width to 32 bits */ 71 popts->data_bus_width = 1; 72 popts->otf_burst_chop_en = 0; 73 popts->burst_length = DDR_BL8; 74 75 /* 76 * Factors to consider for half-strength driver enable: 77 * - number of DIMMs installed 78 */ 79 popts->half_strength_driver_enable = 1; 80 /* 81 * Write leveling override 82 */ 83 popts->wrlvl_override = 1; 84 popts->wrlvl_sample = 0xf; 85 86 /* 87 * Rtt and Rtt_WR override 88 */ 89 popts->rtt_override = 0; 90 91 /* Enable ZQ calibration */ 92 popts->zq_en = 1; 93 94 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm); 95 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) | 96 DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */ 97 } 98 99 /* DDR model number: MT40A512M8HX-093E */ 100 #ifdef CONFIG_SYS_DDR_RAW_TIMING 101 dimm_params_t ddr_raw_timing = { 102 .n_ranks = 1, 103 .rank_density = 2147483648u, 104 .capacity = 2147483648u, 105 .primary_sdram_width = 32, 106 .ec_sdram_width = 0, 107 .registered_dimm = 0, 108 .mirrored_dimm = 0, 109 .n_row_addr = 15, 110 .n_col_addr = 10, 111 .bank_addr_bits = 0, 112 .bank_group_bits = 2, 113 .edc_config = 0, 114 .burst_lengths_bitmask = 0x0c, 115 116 .tckmin_x_ps = 938, 117 .tckmax_ps = 1500, 118 .caslat_x = 0x000DFA00, 119 .taa_ps = 13500, 120 .trcd_ps = 13500, 121 .trp_ps = 13500, 122 .tras_ps = 33000, 123 .trc_ps = 46500, 124 .trfc1_ps = 260000, 125 .trfc2_ps = 160000, 126 .trfc4_ps = 110000, 127 .tfaw_ps = 21000, 128 .trrds_ps = 3700, 129 .trrdl_ps = 5300, 130 .tccdl_ps = 5355, 131 .refresh_rate_ps = 7800000, 132 .dq_mapping[0] = 0x0, 133 .dq_mapping[1] = 0x0, 134 .dq_mapping[2] = 0x0, 135 .dq_mapping[3] = 0x0, 136 .dq_mapping[4] = 0x0, 137 .dq_mapping[5] = 0x0, 138 .dq_mapping[6] = 0x0, 139 .dq_mapping[7] = 0x0, 140 .dq_mapping[8] = 0x0, 141 .dq_mapping[9] = 0x0, 142 .dq_mapping[10] = 0x0, 143 .dq_mapping[11] = 0x0, 144 .dq_mapping[12] = 0x0, 145 .dq_mapping[13] = 0x0, 146 .dq_mapping[14] = 0x0, 147 .dq_mapping[15] = 0x0, 148 .dq_mapping[16] = 0x0, 149 .dq_mapping[17] = 0x0, 150 .dq_mapping_ors = 0, 151 }; 152 153 int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, 154 unsigned int controller_number, 155 unsigned int dimm_number) 156 { 157 static const char dimm_model[] = "Fixed DDR on board"; 158 159 if (((controller_number == 0) && (dimm_number == 0)) || 160 ((controller_number == 1) && (dimm_number == 0))) { 161 memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); 162 memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); 163 memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); 164 } 165 166 return 0; 167 } 168 #endif 169 170 phys_size_t initdram(int board_type) 171 { 172 phys_size_t dram_size; 173 174 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL) 175 puts("Initializing DDR....\n"); 176 dram_size = fsl_ddr_sdram(); 177 #else 178 dram_size = fsl_ddr_sdram_size(); 179 #endif 180 erratum_a008850_post(); 181 182 #ifdef CONFIG_FSL_DEEP_SLEEP 183 fsl_dp_ddr_restore(); 184 #endif 185 186 return dram_size; 187 } 188 189 void dram_init_banksize(void) 190 { 191 /* 192 * gd->secure_ram tracks the location of secure memory. 193 * It was set as if the memory starts from 0. 194 * The address needs to add the offset of its bank. 195 */ 196 gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; 197 if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) { 198 gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE; 199 gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE; 200 gd->bd->bi_dram[1].size = gd->ram_size - 201 CONFIG_SYS_DDR_BLOCK1_SIZE; 202 #ifdef CONFIG_SYS_MEM_RESERVE_SECURE 203 gd->secure_ram = gd->bd->bi_dram[1].start + 204 gd->secure_ram - 205 CONFIG_SYS_DDR_BLOCK1_SIZE; 206 gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED; 207 #endif 208 } else { 209 gd->bd->bi_dram[0].size = gd->ram_size; 210 #ifdef CONFIG_SYS_MEM_RESERVE_SECURE 211 gd->secure_ram = gd->bd->bi_dram[0].start + gd->secure_ram; 212 gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED; 213 #endif 214 } 215 } 216