1 /*
2  * Copyright 2015 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #include <common.h>
8 #include <i2c.h>
9 #include <fdt_support.h>
10 #include <asm/io.h>
11 #include <asm/arch/clock.h>
12 #include <asm/arch/fsl_serdes.h>
13 #include <asm/arch/fdt.h>
14 #include <asm/arch/soc.h>
15 #include <ahci.h>
16 #include <hwconfig.h>
17 #include <mmc.h>
18 #include <scsi.h>
19 #include <fm_eth.h>
20 #include <fsl_csu.h>
21 #include <fsl_esdhc.h>
22 #include <fsl_ifc.h>
23 #include <spl.h>
24 
25 #include "../common/qixis.h"
26 #include "ls1043aqds_qixis.h"
27 
28 DECLARE_GLOBAL_DATA_PTR;
29 
30 enum {
31 	MUX_TYPE_GPIO,
32 };
33 
34 /* LS1043AQDS serdes mux */
35 #define CFG_SD_MUX1_SLOT2	0x0 /* SLOT2 TX/RX0 */
36 #define CFG_SD_MUX1_SLOT1	0x1 /* SLOT1 TX/RX1 */
37 #define CFG_SD_MUX2_SLOT3	0x0 /* SLOT3 TX/RX0 */
38 #define CFG_SD_MUX2_SLOT1	0x1 /* SLOT1 TX/RX2 */
39 #define CFG_SD_MUX3_SLOT4	0x0 /* SLOT4 TX/RX0 */
40 #define CFG_SD_MUX3_MUX4	0x1 /* MUX4 */
41 #define CFG_SD_MUX4_SLOT3	0x0 /* SLOT3 TX/RX1 */
42 #define CFG_SD_MUX4_SLOT1	0x1 /* SLOT1 TX/RX3 */
43 #define CFG_UART_MUX_MASK	0x6
44 #define CFG_UART_MUX_SHIFT	1
45 #define CFG_LPUART_EN		0x1
46 
47 int checkboard(void)
48 {
49 	char buf[64];
50 #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
51 	u8 sw;
52 #endif
53 
54 	puts("Board: LS1043AQDS, boot from ");
55 
56 #ifdef CONFIG_SD_BOOT
57 	puts("SD\n");
58 #elif defined(CONFIG_QSPI_BOOT)
59 	puts("QSPI\n");
60 #else
61 	sw = QIXIS_READ(brdcfg[0]);
62 	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
63 
64 	if (sw < 0x8)
65 		printf("vBank: %d\n", sw);
66 	else if (sw == 0x8)
67 		puts("PromJet\n");
68 	else if (sw == 0x9)
69 		puts("NAND\n");
70 	else if (sw == 0x15)
71 		printf("IFCCard\n");
72 	else
73 		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
74 #endif
75 
76 	printf("Sys ID: 0x%02x, Sys Ver: 0x%02x\n",
77 	       QIXIS_READ(id), QIXIS_READ(arch));
78 
79 	printf("FPGA:  v%d (%s), build %d\n",
80 	       (int)QIXIS_READ(scver), qixis_read_tag(buf),
81 	       (int)qixis_read_minor());
82 
83 	return 0;
84 }
85 
86 bool if_board_diff_clk(void)
87 {
88 	u8 diff_conf = QIXIS_READ(brdcfg[11]);
89 
90 	return diff_conf & 0x40;
91 }
92 
93 unsigned long get_board_sys_clk(void)
94 {
95 	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
96 
97 	switch (sysclk_conf & 0x0f) {
98 	case QIXIS_SYSCLK_64:
99 		return 64000000;
100 	case QIXIS_SYSCLK_83:
101 		return 83333333;
102 	case QIXIS_SYSCLK_100:
103 		return 100000000;
104 	case QIXIS_SYSCLK_125:
105 		return 125000000;
106 	case QIXIS_SYSCLK_133:
107 		return 133333333;
108 	case QIXIS_SYSCLK_150:
109 		return 150000000;
110 	case QIXIS_SYSCLK_160:
111 		return 160000000;
112 	case QIXIS_SYSCLK_166:
113 		return 166666666;
114 	}
115 
116 	return 66666666;
117 }
118 
119 unsigned long get_board_ddr_clk(void)
120 {
121 	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
122 
123 	if (if_board_diff_clk())
124 		return get_board_sys_clk();
125 	switch ((ddrclk_conf & 0x30) >> 4) {
126 	case QIXIS_DDRCLK_100:
127 		return 100000000;
128 	case QIXIS_DDRCLK_125:
129 		return 125000000;
130 	case QIXIS_DDRCLK_133:
131 		return 133333333;
132 	}
133 
134 	return 66666666;
135 }
136 
137 int select_i2c_ch_pca9547(u8 ch)
138 {
139 	int ret;
140 
141 	ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
142 	if (ret) {
143 		puts("PCA: failed to select proper channel\n");
144 		return ret;
145 	}
146 
147 	return 0;
148 }
149 
150 int dram_init(void)
151 {
152 	/*
153 	 * When resuming from deep sleep, the I2C channel may not be
154 	 * in the default channel. So, switch to the default channel
155 	 * before accessing DDR SPD.
156 	 */
157 	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
158 	gd->ram_size = initdram(0);
159 
160 	return 0;
161 }
162 
163 int i2c_multiplexer_select_vid_channel(u8 channel)
164 {
165 	return select_i2c_ch_pca9547(channel);
166 }
167 
168 void board_retimer_init(void)
169 {
170 	u8 reg;
171 
172 	/* Retimer is connected to I2C1_CH7_CH5 */
173 	select_i2c_ch_pca9547(I2C_MUX_CH7);
174 	reg = I2C_MUX_CH5;
175 	i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, &reg, 1);
176 
177 	/* Access to Control/Shared register */
178 	reg = 0x0;
179 	i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);
180 
181 	/* Read device revision and ID */
182 	i2c_read(I2C_RETIMER_ADDR, 1, 1, &reg, 1);
183 	debug("Retimer version id = 0x%x\n", reg);
184 
185 	/* Enable Broadcast. All writes target all channel register sets */
186 	reg = 0x0c;
187 	i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);
188 
189 	/* Reset Channel Registers */
190 	i2c_read(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
191 	reg |= 0x4;
192 	i2c_write(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
193 
194 	/* Enable override divider select and Enable Override Output Mux */
195 	i2c_read(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
196 	reg |= 0x24;
197 	i2c_write(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
198 
199 	/* Select VCO Divider to full rate (000) */
200 	i2c_read(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
201 	reg &= 0x8f;
202 	i2c_write(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
203 
204 	/* Selects active PFD MUX Input as Re-timed Data (001) */
205 	i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
206 	reg &= 0x3f;
207 	reg |= 0x20;
208 	i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
209 
210 	/* Set data rate as 10.3125 Gbps */
211 	reg = 0x0;
212 	i2c_write(I2C_RETIMER_ADDR, 0x60, 1, &reg, 1);
213 	reg = 0xb2;
214 	i2c_write(I2C_RETIMER_ADDR, 0x61, 1, &reg, 1);
215 	reg = 0x90;
216 	i2c_write(I2C_RETIMER_ADDR, 0x62, 1, &reg, 1);
217 	reg = 0xb3;
218 	i2c_write(I2C_RETIMER_ADDR, 0x63, 1, &reg, 1);
219 	reg = 0xcd;
220 	i2c_write(I2C_RETIMER_ADDR, 0x64, 1, &reg, 1);
221 
222 	/* Return the default channel */
223 	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
224 }
225 
226 int board_early_init_f(void)
227 {
228 #ifdef CONFIG_HAS_FSL_XHCI_USB
229 	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
230 	u32 usb_pwrfault;
231 #endif
232 #ifdef CONFIG_LPUART
233 	u8 uart;
234 #endif
235 	fsl_lsch2_early_init_f();
236 
237 #ifdef CONFIG_HAS_FSL_XHCI_USB
238 	out_be32(&scfg->rcwpmuxcr0, 0x3333);
239 	out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
240 	usb_pwrfault =
241 		(SCFG_USBPWRFAULT_SHARED << SCFG_USBPWRFAULT_USB3_SHIFT) |
242 		(SCFG_USBPWRFAULT_SHARED << SCFG_USBPWRFAULT_USB2_SHIFT) |
243 		(SCFG_USBPWRFAULT_SHARED << SCFG_USBPWRFAULT_USB1_SHIFT);
244 	out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
245 #endif
246 
247 #ifdef CONFIG_LPUART
248 	/* We use lpuart0 as system console */
249 	uart = QIXIS_READ(brdcfg[14]);
250 	uart &= ~CFG_UART_MUX_MASK;
251 	uart |= CFG_LPUART_EN << CFG_UART_MUX_SHIFT;
252 	QIXIS_WRITE(brdcfg[14], uart);
253 #endif
254 
255 	return 0;
256 }
257 
258 #ifdef CONFIG_FSL_DEEP_SLEEP
259 /* determine if it is a warm boot */
260 bool is_warm_boot(void)
261 {
262 #define DCFG_CCSR_CRSTSR_WDRFR	(1 << 3)
263 	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
264 
265 	if (in_be32(&gur->crstsr) & DCFG_CCSR_CRSTSR_WDRFR)
266 		return 1;
267 
268 	return 0;
269 }
270 #endif
271 
272 int config_board_mux(int ctrl_type)
273 {
274 	u8 reg14;
275 
276 	reg14 = QIXIS_READ(brdcfg[14]);
277 
278 	switch (ctrl_type) {
279 	case MUX_TYPE_GPIO:
280 		reg14 = (reg14 & (~0x30)) | 0x20;
281 		break;
282 	default:
283 		puts("Unsupported mux interface type\n");
284 		return -1;
285 	}
286 
287 	QIXIS_WRITE(brdcfg[14], reg14);
288 
289 	return 0;
290 }
291 
292 int config_serdes_mux(void)
293 {
294 	return 0;
295 }
296 
297 
298 #ifdef CONFIG_MISC_INIT_R
299 int misc_init_r(void)
300 {
301 	if (hwconfig("gpio"))
302 		config_board_mux(MUX_TYPE_GPIO);
303 
304 	return 0;
305 }
306 #endif
307 
308 int board_init(void)
309 {
310 	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)
311 				   CONFIG_SYS_CCI400_ADDR;
312 
313 	/* Set CCI-400 control override register to enable barrier
314 	 * transaction */
315 	out_le32(&cci->ctrl_ord,
316 		 CCI400_CTRLORD_EN_BARRIER);
317 
318 	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
319 	board_retimer_init();
320 
321 #ifdef CONFIG_SYS_FSL_SERDES
322 	config_serdes_mux();
323 #endif
324 
325 #ifdef CONFIG_LAYERSCAPE_NS_ACCESS
326 	enable_layerscape_ns_access();
327 #endif
328 
329 #ifdef CONFIG_ENV_IS_NOWHERE
330 	gd->env_addr = (ulong)&default_environment[0];
331 #endif
332 	return 0;
333 }
334 
335 #ifdef CONFIG_OF_BOARD_SETUP
336 int ft_board_setup(void *blob, bd_t *bd)
337 {
338 	u64 base[CONFIG_NR_DRAM_BANKS];
339 	u64 size[CONFIG_NR_DRAM_BANKS];
340 
341 	/* fixup DT for the two DDR banks */
342 	base[0] = gd->bd->bi_dram[0].start;
343 	size[0] = gd->bd->bi_dram[0].size;
344 	base[1] = gd->bd->bi_dram[1].start;
345 	size[1] = gd->bd->bi_dram[1].size;
346 
347 	fdt_fixup_memory_banks(blob, base, size, 2);
348 	ft_cpu_setup(blob, bd);
349 
350 #ifdef CONFIG_SYS_DPAA_FMAN
351 	fdt_fixup_fman_ethernet(blob);
352 	fdt_fixup_board_enet(blob);
353 #endif
354 	return 0;
355 }
356 #endif
357 
358 u8 flash_read8(void *addr)
359 {
360 	return __raw_readb(addr + 1);
361 }
362 
363 void flash_write16(u16 val, void *addr)
364 {
365 	u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
366 
367 	__raw_writew(shftval, addr);
368 }
369 
370 u16 flash_read16(void *addr)
371 {
372 	u16 val = __raw_readw(addr);
373 
374 	return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
375 }
376