1 /* 2 * Copyright 2015 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <fsl_ddr_sdram.h> 9 #include <fsl_ddr_dimm_params.h> 10 #ifdef CONFIG_FSL_DEEP_SLEEP 11 #include <fsl_sleep.h> 12 #endif 13 #include "ddr.h" 14 15 DECLARE_GLOBAL_DATA_PTR; 16 17 void fsl_ddr_board_options(memctl_options_t *popts, 18 dimm_params_t *pdimm, 19 unsigned int ctrl_num) 20 { 21 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; 22 ulong ddr_freq; 23 24 if (ctrl_num > 3) { 25 printf("Not supported controller number %d\n", ctrl_num); 26 return; 27 } 28 if (!pdimm->n_ranks) 29 return; 30 31 pbsp = udimms[0]; 32 33 /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr 34 * freqency and n_banks specified in board_specific_parameters table. 35 */ 36 ddr_freq = get_ddr_freq(0) / 1000000; 37 while (pbsp->datarate_mhz_high) { 38 if (pbsp->n_ranks == pdimm->n_ranks) { 39 if (ddr_freq <= pbsp->datarate_mhz_high) { 40 popts->clk_adjust = pbsp->clk_adjust; 41 popts->wrlvl_start = pbsp->wrlvl_start; 42 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 43 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 44 popts->cpo_override = pbsp->cpo_override; 45 popts->write_data_delay = 46 pbsp->write_data_delay; 47 goto found; 48 } 49 pbsp_highest = pbsp; 50 } 51 pbsp++; 52 } 53 54 if (pbsp_highest) { 55 printf("Error: board specific timing not found for %lu MT/s\n", 56 ddr_freq); 57 printf("Trying to use the highest speed (%u) parameters\n", 58 pbsp_highest->datarate_mhz_high); 59 popts->clk_adjust = pbsp_highest->clk_adjust; 60 popts->wrlvl_start = pbsp_highest->wrlvl_start; 61 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 62 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 63 } else { 64 panic("DIMM is not supported by this board"); 65 } 66 found: 67 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", 68 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); 69 70 /* force DDR bus width to 32 bits */ 71 popts->data_bus_width = 1; 72 popts->otf_burst_chop_en = 0; 73 popts->burst_length = DDR_BL8; 74 popts->bstopre = 0; /* enable auto precharge */ 75 76 /* 77 * Factors to consider for half-strength driver enable: 78 * - number of DIMMs installed 79 */ 80 popts->half_strength_driver_enable = 1; 81 /* 82 * Write leveling override 83 */ 84 popts->wrlvl_override = 1; 85 popts->wrlvl_sample = 0xf; 86 87 /* 88 * Rtt and Rtt_WR override 89 */ 90 popts->rtt_override = 0; 91 92 /* Enable ZQ calibration */ 93 popts->zq_en = 1; 94 95 #ifdef CONFIG_SYS_FSL_DDR4 96 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm); 97 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) | 98 DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */ 99 #else 100 popts->cswl_override = DDR_CSWL_CS0; 101 102 /* DHC_EN =1, ODT = 75 Ohm */ 103 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); 104 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); 105 #endif 106 } 107 108 phys_size_t initdram(int board_type) 109 { 110 phys_size_t dram_size; 111 112 #if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD) 113 return fsl_ddr_sdram_size(); 114 #else 115 puts("Initializing DDR....using SPD\n"); 116 117 dram_size = fsl_ddr_sdram(); 118 #endif 119 120 #ifdef CONFIG_FSL_DEEP_SLEEP 121 fsl_dp_ddr_restore(); 122 #endif 123 124 return dram_size; 125 } 126 127 void dram_init_banksize(void) 128 { 129 gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; 130 gd->bd->bi_dram[0].size = gd->ram_size; 131 } 132