1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <i2c.h> 9 #include <asm/io.h> 10 #include <asm/arch/immap_ls102xa.h> 11 #include <asm/arch/clock.h> 12 #include <asm/arch/fsl_serdes.h> 13 #include <asm/arch/ls102xa_devdis.h> 14 #include <asm/arch/ls102xa_soc.h> 15 #include <asm/arch/ls102xa_sata.h> 16 #include <hwconfig.h> 17 #include <mmc.h> 18 #include <fsl_csu.h> 19 #include <fsl_esdhc.h> 20 #include <fsl_ifc.h> 21 #include <fsl_immap.h> 22 #include <netdev.h> 23 #include <fsl_mdio.h> 24 #include <tsec.h> 25 #include <fsl_sec.h> 26 #include <fsl_devdis.h> 27 #include <spl.h> 28 #include "../common/sleep.h" 29 #ifdef CONFIG_U_QE 30 #include <fsl_qe.h> 31 #endif 32 #include <fsl_validate.h> 33 34 35 DECLARE_GLOBAL_DATA_PTR; 36 37 #define VERSION_MASK 0x00FF 38 #define BANK_MASK 0x0001 39 #define CONFIG_RESET 0x1 40 #define INIT_RESET 0x1 41 42 #define CPLD_SET_MUX_SERDES 0x20 43 #define CPLD_SET_BOOT_BANK 0x40 44 45 #define BOOT_FROM_UPPER_BANK 0x0 46 #define BOOT_FROM_LOWER_BANK 0x1 47 48 #define LANEB_SATA (0x01) 49 #define LANEB_SGMII1 (0x02) 50 #define LANEC_SGMII1 (0x04) 51 #define LANEC_PCIEX1 (0x08) 52 #define LANED_PCIEX2 (0x10) 53 #define LANED_SGMII2 (0x20) 54 55 #define MASK_LANE_B 0x1 56 #define MASK_LANE_C 0x2 57 #define MASK_LANE_D 0x4 58 #define MASK_SGMII 0x8 59 60 #define KEEP_STATUS 0x0 61 #define NEED_RESET 0x1 62 63 #define SOFT_MUX_ON_I2C3_IFC 0x2 64 #define SOFT_MUX_ON_CAN3_USB2 0x8 65 #define SOFT_MUX_ON_QE_LCD 0x10 66 67 #define PIN_I2C3_IFC_MUX_I2C3 0x0 68 #define PIN_I2C3_IFC_MUX_IFC 0x1 69 #define PIN_CAN3_USB2_MUX_USB2 0x0 70 #define PIN_CAN3_USB2_MUX_CAN3 0x1 71 #define PIN_QE_LCD_MUX_LCD 0x0 72 #define PIN_QE_LCD_MUX_QE 0x1 73 74 struct cpld_data { 75 u8 cpld_ver; /* cpld revision */ 76 u8 cpld_ver_sub; /* cpld sub revision */ 77 u8 pcba_ver; /* pcb revision number */ 78 u8 system_rst; /* reset system by cpld */ 79 u8 soft_mux_on; /* CPLD override physical switches Enable */ 80 u8 cfg_rcw_src1; /* Reset config word 1 */ 81 u8 cfg_rcw_src2; /* Reset config word 2 */ 82 u8 vbank; /* Flash bank selection Control */ 83 u8 gpio; /* GPIO for TWR-ELEV */ 84 u8 i2c3_ifc_mux; 85 u8 mux_spi2; 86 u8 can3_usb2_mux; /* CAN3 and USB2 Selection */ 87 u8 qe_lcd_mux; /* QE and LCD Selection */ 88 u8 serdes_mux; /* Multiplexed pins for SerDes Lanes */ 89 u8 global_rst; /* reset with init CPLD reg to default */ 90 u8 rev1; /* Reserved */ 91 u8 rev2; /* Reserved */ 92 }; 93 94 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 95 static void convert_serdes_mux(int type, int need_reset); 96 97 void cpld_show(void) 98 { 99 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 100 101 printf("CPLD: V%x.%x\nPCBA: V%x.0\nVBank: %d\n", 102 in_8(&cpld_data->cpld_ver) & VERSION_MASK, 103 in_8(&cpld_data->cpld_ver_sub) & VERSION_MASK, 104 in_8(&cpld_data->pcba_ver) & VERSION_MASK, 105 in_8(&cpld_data->vbank) & BANK_MASK); 106 107 #ifdef CONFIG_DEBUG 108 printf("soft_mux_on =%x\n", 109 in_8(&cpld_data->soft_mux_on)); 110 printf("cfg_rcw_src1 =%x\n", 111 in_8(&cpld_data->cfg_rcw_src1)); 112 printf("cfg_rcw_src2 =%x\n", 113 in_8(&cpld_data->cfg_rcw_src2)); 114 printf("vbank =%x\n", 115 in_8(&cpld_data->vbank)); 116 printf("gpio =%x\n", 117 in_8(&cpld_data->gpio)); 118 printf("i2c3_ifc_mux =%x\n", 119 in_8(&cpld_data->i2c3_ifc_mux)); 120 printf("mux_spi2 =%x\n", 121 in_8(&cpld_data->mux_spi2)); 122 printf("can3_usb2_mux =%x\n", 123 in_8(&cpld_data->can3_usb2_mux)); 124 printf("qe_lcd_mux =%x\n", 125 in_8(&cpld_data->qe_lcd_mux)); 126 printf("serdes_mux =%x\n", 127 in_8(&cpld_data->serdes_mux)); 128 #endif 129 } 130 #endif 131 132 int checkboard(void) 133 { 134 puts("Board: LS1021ATWR\n"); 135 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 136 cpld_show(); 137 #endif 138 139 return 0; 140 } 141 142 void ddrmc_init(void) 143 { 144 struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR; 145 u32 temp_sdram_cfg; 146 147 out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG); 148 149 out_be32(&ddr->cs0_bnds, DDR_CS0_BNDS); 150 out_be32(&ddr->cs0_config, DDR_CS0_CONFIG); 151 152 out_be32(&ddr->timing_cfg_0, DDR_TIMING_CFG_0); 153 out_be32(&ddr->timing_cfg_1, DDR_TIMING_CFG_1); 154 out_be32(&ddr->timing_cfg_2, DDR_TIMING_CFG_2); 155 out_be32(&ddr->timing_cfg_3, DDR_TIMING_CFG_3); 156 out_be32(&ddr->timing_cfg_4, DDR_TIMING_CFG_4); 157 out_be32(&ddr->timing_cfg_5, DDR_TIMING_CFG_5); 158 159 #ifdef CONFIG_DEEP_SLEEP 160 if (is_warm_boot()) { 161 out_be32(&ddr->sdram_cfg_2, 162 DDR_SDRAM_CFG_2 & ~SDRAM_CFG2_D_INIT); 163 out_be32(&ddr->init_addr, CONFIG_SYS_SDRAM_BASE); 164 out_be32(&ddr->init_ext_addr, (1 << 31)); 165 166 /* DRAM VRef will not be trained */ 167 out_be32(&ddr->ddr_cdr2, 168 DDR_DDR_CDR2 & ~DDR_CDR2_VREF_TRAIN_EN); 169 } else 170 #endif 171 { 172 out_be32(&ddr->sdram_cfg_2, DDR_SDRAM_CFG_2); 173 out_be32(&ddr->ddr_cdr2, DDR_DDR_CDR2); 174 } 175 176 out_be32(&ddr->sdram_mode, DDR_SDRAM_MODE); 177 out_be32(&ddr->sdram_mode_2, DDR_SDRAM_MODE_2); 178 179 out_be32(&ddr->sdram_interval, DDR_SDRAM_INTERVAL); 180 181 out_be32(&ddr->ddr_wrlvl_cntl, DDR_DDR_WRLVL_CNTL); 182 183 out_be32(&ddr->ddr_wrlvl_cntl_2, DDR_DDR_WRLVL_CNTL_2); 184 out_be32(&ddr->ddr_wrlvl_cntl_3, DDR_DDR_WRLVL_CNTL_3); 185 186 out_be32(&ddr->ddr_cdr1, DDR_DDR_CDR1); 187 188 out_be32(&ddr->sdram_clk_cntl, DDR_SDRAM_CLK_CNTL); 189 out_be32(&ddr->ddr_zq_cntl, DDR_DDR_ZQ_CNTL); 190 191 out_be32(&ddr->cs0_config_2, DDR_CS0_CONFIG_2); 192 udelay(1); 193 194 #ifdef CONFIG_DEEP_SLEEP 195 if (is_warm_boot()) { 196 /* enter self-refresh */ 197 temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2); 198 temp_sdram_cfg |= SDRAM_CFG2_FRC_SR; 199 out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg); 200 201 temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN | SDRAM_CFG_BI); 202 } else 203 #endif 204 temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN & ~SDRAM_CFG_BI); 205 206 out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG | temp_sdram_cfg); 207 208 #ifdef CONFIG_DEEP_SLEEP 209 if (is_warm_boot()) { 210 /* exit self-refresh */ 211 temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2); 212 temp_sdram_cfg &= ~SDRAM_CFG2_FRC_SR; 213 out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg); 214 } 215 #endif 216 } 217 218 int dram_init(void) 219 { 220 #if (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)) 221 ddrmc_init(); 222 #endif 223 224 gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); 225 226 #if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD) 227 fsl_dp_resume(); 228 #endif 229 230 return 0; 231 } 232 233 #ifdef CONFIG_FSL_ESDHC 234 struct fsl_esdhc_cfg esdhc_cfg[1] = { 235 {CONFIG_SYS_FSL_ESDHC_ADDR}, 236 }; 237 238 int board_mmc_init(bd_t *bis) 239 { 240 esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 241 242 return fsl_esdhc_initialize(bis, &esdhc_cfg[0]); 243 } 244 #endif 245 246 int board_eth_init(bd_t *bis) 247 { 248 #ifdef CONFIG_TSEC_ENET 249 struct fsl_pq_mdio_info mdio_info; 250 struct tsec_info_struct tsec_info[4]; 251 int num = 0; 252 253 #ifdef CONFIG_TSEC1 254 SET_STD_TSEC_INFO(tsec_info[num], 1); 255 if (is_serdes_configured(SGMII_TSEC1)) { 256 puts("eTSEC1 is in sgmii mode.\n"); 257 tsec_info[num].flags |= TSEC_SGMII; 258 } 259 num++; 260 #endif 261 #ifdef CONFIG_TSEC2 262 SET_STD_TSEC_INFO(tsec_info[num], 2); 263 if (is_serdes_configured(SGMII_TSEC2)) { 264 puts("eTSEC2 is in sgmii mode.\n"); 265 tsec_info[num].flags |= TSEC_SGMII; 266 } 267 num++; 268 #endif 269 #ifdef CONFIG_TSEC3 270 SET_STD_TSEC_INFO(tsec_info[num], 3); 271 num++; 272 #endif 273 if (!num) { 274 printf("No TSECs initialized\n"); 275 return 0; 276 } 277 278 mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; 279 mdio_info.name = DEFAULT_MII_NAME; 280 fsl_pq_mdio_init(bis, &mdio_info); 281 282 tsec_eth_init(bis, tsec_info, num); 283 #endif 284 285 return pci_eth_init(bis); 286 } 287 288 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 289 int config_serdes_mux(void) 290 { 291 struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); 292 u32 protocol = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK; 293 294 protocol >>= RCWSR4_SRDS1_PRTCL_SHIFT; 295 switch (protocol) { 296 case 0x10: 297 convert_serdes_mux(LANEB_SATA, KEEP_STATUS); 298 convert_serdes_mux(LANED_PCIEX2 | 299 LANEC_PCIEX1, KEEP_STATUS); 300 break; 301 case 0x20: 302 convert_serdes_mux(LANEB_SGMII1, KEEP_STATUS); 303 convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS); 304 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); 305 break; 306 case 0x30: 307 convert_serdes_mux(LANEB_SATA, KEEP_STATUS); 308 convert_serdes_mux(LANEC_SGMII1, KEEP_STATUS); 309 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); 310 break; 311 case 0x70: 312 convert_serdes_mux(LANEB_SATA, KEEP_STATUS); 313 convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS); 314 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); 315 break; 316 } 317 318 return 0; 319 } 320 #endif 321 322 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 323 int config_board_mux(void) 324 { 325 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 326 int conflict_flag; 327 328 conflict_flag = 0; 329 if (hwconfig("i2c3")) { 330 conflict_flag++; 331 cpld_data->soft_mux_on |= SOFT_MUX_ON_I2C3_IFC; 332 cpld_data->i2c3_ifc_mux = PIN_I2C3_IFC_MUX_I2C3; 333 } 334 335 if (hwconfig("ifc")) { 336 conflict_flag++; 337 /* some signals can not enable simultaneous*/ 338 if (conflict_flag > 1) 339 goto conflict; 340 cpld_data->soft_mux_on |= SOFT_MUX_ON_I2C3_IFC; 341 cpld_data->i2c3_ifc_mux = PIN_I2C3_IFC_MUX_IFC; 342 } 343 344 conflict_flag = 0; 345 if (hwconfig("usb2")) { 346 conflict_flag++; 347 cpld_data->soft_mux_on |= SOFT_MUX_ON_CAN3_USB2; 348 cpld_data->can3_usb2_mux = PIN_CAN3_USB2_MUX_USB2; 349 } 350 351 if (hwconfig("can3")) { 352 conflict_flag++; 353 /* some signals can not enable simultaneous*/ 354 if (conflict_flag > 1) 355 goto conflict; 356 cpld_data->soft_mux_on |= SOFT_MUX_ON_CAN3_USB2; 357 cpld_data->can3_usb2_mux = PIN_CAN3_USB2_MUX_CAN3; 358 } 359 360 conflict_flag = 0; 361 if (hwconfig("lcd")) { 362 conflict_flag++; 363 cpld_data->soft_mux_on |= SOFT_MUX_ON_QE_LCD; 364 cpld_data->qe_lcd_mux = PIN_QE_LCD_MUX_LCD; 365 } 366 367 if (hwconfig("qe")) { 368 conflict_flag++; 369 /* some signals can not enable simultaneous*/ 370 if (conflict_flag > 1) 371 goto conflict; 372 cpld_data->soft_mux_on |= SOFT_MUX_ON_QE_LCD; 373 cpld_data->qe_lcd_mux = PIN_QE_LCD_MUX_QE; 374 } 375 376 return 0; 377 378 conflict: 379 printf("WARNING: pin conflict! MUX setting may failed!\n"); 380 return 0; 381 } 382 #endif 383 384 int board_early_init_f(void) 385 { 386 struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; 387 388 #ifdef CONFIG_TSEC_ENET 389 /* clear BD & FR bits for BE BD's and frame data */ 390 clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); 391 out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); 392 #endif 393 394 #ifdef CONFIG_FSL_IFC 395 init_early_memctl_regs(); 396 #endif 397 398 arch_soc_init(); 399 400 #if defined(CONFIG_DEEP_SLEEP) 401 if (is_warm_boot()) { 402 timer_init(); 403 dram_init(); 404 } 405 #endif 406 407 return 0; 408 } 409 410 #ifdef CONFIG_SPL_BUILD 411 void board_init_f(ulong dummy) 412 { 413 void (*second_uboot)(void); 414 415 /* Clear the BSS */ 416 memset(__bss_start, 0, __bss_end - __bss_start); 417 418 get_clocks(); 419 420 #if defined(CONFIG_DEEP_SLEEP) 421 if (is_warm_boot()) 422 fsl_dp_disable_console(); 423 #endif 424 425 preloader_console_init(); 426 427 dram_init(); 428 429 /* Allow OCRAM access permission as R/W */ 430 #ifdef CONFIG_LAYERSCAPE_NS_ACCESS 431 enable_layerscape_ns_access(); 432 enable_layerscape_ns_access(); 433 #endif 434 435 /* 436 * if it is woken up from deep sleep, then jump to second 437 * stage uboot and continue executing without recopying 438 * it from SD since it has already been reserved in memeory 439 * in last boot. 440 */ 441 if (is_warm_boot()) { 442 second_uboot = (void (*)(void))CONFIG_SYS_TEXT_BASE; 443 second_uboot(); 444 } 445 446 board_init_r(NULL, 0); 447 } 448 #endif 449 450 #ifdef CONFIG_DEEP_SLEEP 451 /* program the regulator (MC34VR500) to support deep sleep */ 452 void ls1twr_program_regulator(void) 453 { 454 unsigned int i2c_bus; 455 u8 i2c_device_id; 456 457 #define LS1TWR_I2C_BUS_MC34VR500 1 458 #define MC34VR500_ADDR 0x8 459 #define MC34VR500_DEVICEID 0x4 460 #define MC34VR500_DEVICEID_MASK 0x0f 461 462 i2c_bus = i2c_get_bus_num(); 463 i2c_set_bus_num(LS1TWR_I2C_BUS_MC34VR500); 464 i2c_device_id = i2c_reg_read(MC34VR500_ADDR, 0x0) & 465 MC34VR500_DEVICEID_MASK; 466 if (i2c_device_id != MC34VR500_DEVICEID) { 467 printf("The regulator (MC34VR500) does not exist. The device does not support deep sleep.\n"); 468 return; 469 } 470 471 i2c_reg_write(MC34VR500_ADDR, 0x31, 0x4); 472 i2c_reg_write(MC34VR500_ADDR, 0x4d, 0x4); 473 i2c_reg_write(MC34VR500_ADDR, 0x6d, 0x38); 474 i2c_reg_write(MC34VR500_ADDR, 0x6f, 0x37); 475 i2c_reg_write(MC34VR500_ADDR, 0x71, 0x30); 476 477 i2c_set_bus_num(i2c_bus); 478 } 479 #endif 480 481 int board_init(void) 482 { 483 #ifndef CONFIG_SYS_FSL_NO_SERDES 484 fsl_serdes_init(); 485 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 486 config_serdes_mux(); 487 #endif 488 #endif 489 490 ls102xa_smmu_stream_id_init(); 491 492 #ifdef CONFIG_LAYERSCAPE_NS_ACCESS 493 enable_layerscape_ns_access(); 494 #endif 495 496 #ifdef CONFIG_U_QE 497 u_qe_init(); 498 #endif 499 500 #ifdef CONFIG_DEEP_SLEEP 501 ls1twr_program_regulator(); 502 #endif 503 return 0; 504 } 505 506 #ifdef CONFIG_BOARD_LATE_INIT 507 int board_late_init(void) 508 { 509 #ifdef CONFIG_SCSI_AHCI_PLAT 510 ls1021a_sata_init(); 511 #endif 512 #ifdef CONFIG_CHAIN_OF_TRUST 513 fsl_setenv_chain_of_trust(); 514 #endif 515 516 return 0; 517 } 518 #endif 519 520 #if defined(CONFIG_MISC_INIT_R) 521 int misc_init_r(void) 522 { 523 #ifdef CONFIG_FSL_DEVICE_DISABLE 524 device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl)); 525 #endif 526 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 527 config_board_mux(); 528 #endif 529 530 #ifdef CONFIG_FSL_CAAM 531 return sec_init(); 532 #endif 533 } 534 #endif 535 536 #if defined(CONFIG_DEEP_SLEEP) 537 void board_sleep_prepare(void) 538 { 539 #ifdef CONFIG_LAYERSCAPE_NS_ACCESS 540 enable_layerscape_ns_access(); 541 #endif 542 } 543 #endif 544 545 int ft_board_setup(void *blob, bd_t *bd) 546 { 547 ft_cpu_setup(blob, bd); 548 549 #ifdef CONFIG_PCI 550 ft_pci_setup(blob, bd); 551 #endif 552 553 return 0; 554 } 555 556 u8 flash_read8(void *addr) 557 { 558 return __raw_readb(addr + 1); 559 } 560 561 void flash_write16(u16 val, void *addr) 562 { 563 u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00)); 564 565 __raw_writew(shftval, addr); 566 } 567 568 u16 flash_read16(void *addr) 569 { 570 u16 val = __raw_readw(addr); 571 572 return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00); 573 } 574 575 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 576 static void convert_flash_bank(char bank) 577 { 578 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 579 580 printf("Now switch to boot from flash bank %d.\n", bank); 581 cpld_data->soft_mux_on = CPLD_SET_BOOT_BANK; 582 cpld_data->vbank = bank; 583 584 printf("Reset board to enable configuration.\n"); 585 cpld_data->system_rst = CONFIG_RESET; 586 } 587 588 static int flash_bank_cmd(cmd_tbl_t *cmdtp, int flag, int argc, 589 char * const argv[]) 590 { 591 if (argc != 2) 592 return CMD_RET_USAGE; 593 if (strcmp(argv[1], "0") == 0) 594 convert_flash_bank(BOOT_FROM_UPPER_BANK); 595 else if (strcmp(argv[1], "1") == 0) 596 convert_flash_bank(BOOT_FROM_LOWER_BANK); 597 else 598 return CMD_RET_USAGE; 599 600 return 0; 601 } 602 603 U_BOOT_CMD( 604 boot_bank, 2, 0, flash_bank_cmd, 605 "Flash bank Selection Control", 606 "bank[0-upper bank/1-lower bank] (e.g. boot_bank 0)" 607 ); 608 609 static int cpld_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, 610 char * const argv[]) 611 { 612 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 613 614 if (argc > 2) 615 return CMD_RET_USAGE; 616 if ((argc == 1) || (strcmp(argv[1], "conf") == 0)) 617 cpld_data->system_rst = CONFIG_RESET; 618 else if (strcmp(argv[1], "init") == 0) 619 cpld_data->global_rst = INIT_RESET; 620 else 621 return CMD_RET_USAGE; 622 623 return 0; 624 } 625 626 U_BOOT_CMD( 627 cpld_reset, 2, 0, cpld_reset_cmd, 628 "Reset via CPLD", 629 "conf\n" 630 " -reset with current CPLD configuration\n" 631 "init\n" 632 " -reset and initial CPLD configuration with default value" 633 634 ); 635 636 static void convert_serdes_mux(int type, int need_reset) 637 { 638 char current_serdes; 639 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 640 641 current_serdes = cpld_data->serdes_mux; 642 643 switch (type) { 644 case LANEB_SATA: 645 current_serdes &= ~MASK_LANE_B; 646 break; 647 case LANEB_SGMII1: 648 current_serdes |= (MASK_LANE_B | MASK_SGMII | MASK_LANE_C); 649 break; 650 case LANEC_SGMII1: 651 current_serdes &= ~(MASK_LANE_B | MASK_SGMII | MASK_LANE_C); 652 break; 653 case LANED_SGMII2: 654 current_serdes |= MASK_LANE_D; 655 break; 656 case LANEC_PCIEX1: 657 current_serdes |= MASK_LANE_C; 658 break; 659 case (LANED_PCIEX2 | LANEC_PCIEX1): 660 current_serdes |= MASK_LANE_C; 661 current_serdes &= ~MASK_LANE_D; 662 break; 663 default: 664 printf("CPLD serdes MUX: unsupported MUX type 0x%x\n", type); 665 return; 666 } 667 668 cpld_data->soft_mux_on |= CPLD_SET_MUX_SERDES; 669 cpld_data->serdes_mux = current_serdes; 670 671 if (need_reset == 1) { 672 printf("Reset board to enable configuration\n"); 673 cpld_data->system_rst = CONFIG_RESET; 674 } 675 } 676 677 void print_serdes_mux(void) 678 { 679 char current_serdes; 680 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 681 682 current_serdes = cpld_data->serdes_mux; 683 684 printf("Serdes Lane B: "); 685 if ((current_serdes & MASK_LANE_B) == 0) 686 printf("SATA,\n"); 687 else 688 printf("SGMII 1,\n"); 689 690 printf("Serdes Lane C: "); 691 if ((current_serdes & MASK_LANE_C) == 0) 692 printf("SGMII 1,\n"); 693 else 694 printf("PCIe,\n"); 695 696 printf("Serdes Lane D: "); 697 if ((current_serdes & MASK_LANE_D) == 0) 698 printf("PCIe,\n"); 699 else 700 printf("SGMII 2,\n"); 701 702 printf("SGMII 1 is on lane "); 703 if ((current_serdes & MASK_SGMII) == 0) 704 printf("C.\n"); 705 else 706 printf("B.\n"); 707 } 708 709 static int serdes_mux_cmd(cmd_tbl_t *cmdtp, int flag, int argc, 710 char * const argv[]) 711 { 712 if (argc != 2) 713 return CMD_RET_USAGE; 714 if (strcmp(argv[1], "sata") == 0) { 715 printf("Set serdes lane B to SATA.\n"); 716 convert_serdes_mux(LANEB_SATA, NEED_RESET); 717 } else if (strcmp(argv[1], "sgmii1b") == 0) { 718 printf("Set serdes lane B to SGMII 1.\n"); 719 convert_serdes_mux(LANEB_SGMII1, NEED_RESET); 720 } else if (strcmp(argv[1], "sgmii1c") == 0) { 721 printf("Set serdes lane C to SGMII 1.\n"); 722 convert_serdes_mux(LANEC_SGMII1, NEED_RESET); 723 } else if (strcmp(argv[1], "sgmii2") == 0) { 724 printf("Set serdes lane D to SGMII 2.\n"); 725 convert_serdes_mux(LANED_SGMII2, NEED_RESET); 726 } else if (strcmp(argv[1], "pciex1") == 0) { 727 printf("Set serdes lane C to PCIe X1.\n"); 728 convert_serdes_mux(LANEC_PCIEX1, NEED_RESET); 729 } else if (strcmp(argv[1], "pciex2") == 0) { 730 printf("Set serdes lane C & lane D to PCIe X2.\n"); 731 convert_serdes_mux((LANED_PCIEX2 | LANEC_PCIEX1), NEED_RESET); 732 } else if (strcmp(argv[1], "show") == 0) { 733 print_serdes_mux(); 734 } else { 735 return CMD_RET_USAGE; 736 } 737 738 return 0; 739 } 740 741 U_BOOT_CMD( 742 lane_bank, 2, 0, serdes_mux_cmd, 743 "Multiplexed function setting for SerDes Lanes", 744 "sata\n" 745 " -change lane B to sata\n" 746 "lane_bank sgmii1b\n" 747 " -change lane B to SGMII1\n" 748 "lane_bank sgmii1c\n" 749 " -change lane C to SGMII1\n" 750 "lane_bank sgmii2\n" 751 " -change lane D to SGMII2\n" 752 "lane_bank pciex1\n" 753 " -change lane C to PCIeX1\n" 754 "lane_bank pciex2\n" 755 " -change lane C & lane D to PCIeX2\n" 756 "\nWARNING: If you aren't familiar with the setting of serdes, don't try to change anything!\n" 757 ); 758 #endif 759