1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright 2014 Freescale Semiconductor, Inc. 4 */ 5 6 #include <common.h> 7 #include <i2c.h> 8 #include <asm/io.h> 9 #include <asm/arch/immap_ls102xa.h> 10 #include <asm/arch/clock.h> 11 #include <asm/arch/fsl_serdes.h> 12 #include <asm/arch/ls102xa_devdis.h> 13 #include <asm/arch/ls102xa_soc.h> 14 #include <hwconfig.h> 15 #include <mmc.h> 16 #include <fsl_csu.h> 17 #include <fsl_esdhc.h> 18 #include <fsl_ifc.h> 19 #include <fsl_immap.h> 20 #include <netdev.h> 21 #include <fsl_mdio.h> 22 #include <tsec.h> 23 #include <fsl_sec.h> 24 #include <fsl_devdis.h> 25 #include <spl.h> 26 #include "../common/sleep.h" 27 #ifdef CONFIG_U_QE 28 #include <fsl_qe.h> 29 #endif 30 #include <fsl_validate.h> 31 32 33 DECLARE_GLOBAL_DATA_PTR; 34 35 #define VERSION_MASK 0x00FF 36 #define BANK_MASK 0x0001 37 #define CONFIG_RESET 0x1 38 #define INIT_RESET 0x1 39 40 #define CPLD_SET_MUX_SERDES 0x20 41 #define CPLD_SET_BOOT_BANK 0x40 42 43 #define BOOT_FROM_UPPER_BANK 0x0 44 #define BOOT_FROM_LOWER_BANK 0x1 45 46 #define LANEB_SATA (0x01) 47 #define LANEB_SGMII1 (0x02) 48 #define LANEC_SGMII1 (0x04) 49 #define LANEC_PCIEX1 (0x08) 50 #define LANED_PCIEX2 (0x10) 51 #define LANED_SGMII2 (0x20) 52 53 #define MASK_LANE_B 0x1 54 #define MASK_LANE_C 0x2 55 #define MASK_LANE_D 0x4 56 #define MASK_SGMII 0x8 57 58 #define KEEP_STATUS 0x0 59 #define NEED_RESET 0x1 60 61 #define SOFT_MUX_ON_I2C3_IFC 0x2 62 #define SOFT_MUX_ON_CAN3_USB2 0x8 63 #define SOFT_MUX_ON_QE_LCD 0x10 64 65 #define PIN_I2C3_IFC_MUX_I2C3 0x0 66 #define PIN_I2C3_IFC_MUX_IFC 0x1 67 #define PIN_CAN3_USB2_MUX_USB2 0x0 68 #define PIN_CAN3_USB2_MUX_CAN3 0x1 69 #define PIN_QE_LCD_MUX_LCD 0x0 70 #define PIN_QE_LCD_MUX_QE 0x1 71 72 struct cpld_data { 73 u8 cpld_ver; /* cpld revision */ 74 u8 cpld_ver_sub; /* cpld sub revision */ 75 u8 pcba_ver; /* pcb revision number */ 76 u8 system_rst; /* reset system by cpld */ 77 u8 soft_mux_on; /* CPLD override physical switches Enable */ 78 u8 cfg_rcw_src1; /* Reset config word 1 */ 79 u8 cfg_rcw_src2; /* Reset config word 2 */ 80 u8 vbank; /* Flash bank selection Control */ 81 u8 gpio; /* GPIO for TWR-ELEV */ 82 u8 i2c3_ifc_mux; 83 u8 mux_spi2; 84 u8 can3_usb2_mux; /* CAN3 and USB2 Selection */ 85 u8 qe_lcd_mux; /* QE and LCD Selection */ 86 u8 serdes_mux; /* Multiplexed pins for SerDes Lanes */ 87 u8 global_rst; /* reset with init CPLD reg to default */ 88 u8 rev1; /* Reserved */ 89 u8 rev2; /* Reserved */ 90 }; 91 92 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 93 static void cpld_show(void) 94 { 95 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 96 97 printf("CPLD: V%x.%x\nPCBA: V%x.0\nVBank: %d\n", 98 in_8(&cpld_data->cpld_ver) & VERSION_MASK, 99 in_8(&cpld_data->cpld_ver_sub) & VERSION_MASK, 100 in_8(&cpld_data->pcba_ver) & VERSION_MASK, 101 in_8(&cpld_data->vbank) & BANK_MASK); 102 103 #ifdef CONFIG_DEBUG 104 printf("soft_mux_on =%x\n", 105 in_8(&cpld_data->soft_mux_on)); 106 printf("cfg_rcw_src1 =%x\n", 107 in_8(&cpld_data->cfg_rcw_src1)); 108 printf("cfg_rcw_src2 =%x\n", 109 in_8(&cpld_data->cfg_rcw_src2)); 110 printf("vbank =%x\n", 111 in_8(&cpld_data->vbank)); 112 printf("gpio =%x\n", 113 in_8(&cpld_data->gpio)); 114 printf("i2c3_ifc_mux =%x\n", 115 in_8(&cpld_data->i2c3_ifc_mux)); 116 printf("mux_spi2 =%x\n", 117 in_8(&cpld_data->mux_spi2)); 118 printf("can3_usb2_mux =%x\n", 119 in_8(&cpld_data->can3_usb2_mux)); 120 printf("qe_lcd_mux =%x\n", 121 in_8(&cpld_data->qe_lcd_mux)); 122 printf("serdes_mux =%x\n", 123 in_8(&cpld_data->serdes_mux)); 124 #endif 125 } 126 #endif 127 128 int checkboard(void) 129 { 130 puts("Board: LS1021ATWR\n"); 131 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 132 cpld_show(); 133 #endif 134 135 return 0; 136 } 137 138 void ddrmc_init(void) 139 { 140 struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR; 141 u32 temp_sdram_cfg, tmp; 142 143 out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG); 144 145 out_be32(&ddr->cs0_bnds, DDR_CS0_BNDS); 146 out_be32(&ddr->cs0_config, DDR_CS0_CONFIG); 147 148 out_be32(&ddr->timing_cfg_0, DDR_TIMING_CFG_0); 149 out_be32(&ddr->timing_cfg_1, DDR_TIMING_CFG_1); 150 out_be32(&ddr->timing_cfg_2, DDR_TIMING_CFG_2); 151 out_be32(&ddr->timing_cfg_3, DDR_TIMING_CFG_3); 152 out_be32(&ddr->timing_cfg_4, DDR_TIMING_CFG_4); 153 out_be32(&ddr->timing_cfg_5, DDR_TIMING_CFG_5); 154 155 #ifdef CONFIG_DEEP_SLEEP 156 if (is_warm_boot()) { 157 out_be32(&ddr->sdram_cfg_2, 158 DDR_SDRAM_CFG_2 & ~SDRAM_CFG2_D_INIT); 159 out_be32(&ddr->init_addr, CONFIG_SYS_SDRAM_BASE); 160 out_be32(&ddr->init_ext_addr, (1 << 31)); 161 162 /* DRAM VRef will not be trained */ 163 out_be32(&ddr->ddr_cdr2, 164 DDR_DDR_CDR2 & ~DDR_CDR2_VREF_TRAIN_EN); 165 } else 166 #endif 167 { 168 out_be32(&ddr->sdram_cfg_2, DDR_SDRAM_CFG_2); 169 out_be32(&ddr->ddr_cdr2, DDR_DDR_CDR2); 170 } 171 172 out_be32(&ddr->sdram_mode, DDR_SDRAM_MODE); 173 out_be32(&ddr->sdram_mode_2, DDR_SDRAM_MODE_2); 174 175 out_be32(&ddr->sdram_interval, DDR_SDRAM_INTERVAL); 176 177 out_be32(&ddr->ddr_wrlvl_cntl, DDR_DDR_WRLVL_CNTL); 178 179 out_be32(&ddr->ddr_wrlvl_cntl_2, DDR_DDR_WRLVL_CNTL_2); 180 out_be32(&ddr->ddr_wrlvl_cntl_3, DDR_DDR_WRLVL_CNTL_3); 181 182 out_be32(&ddr->ddr_cdr1, DDR_DDR_CDR1); 183 184 out_be32(&ddr->sdram_clk_cntl, DDR_SDRAM_CLK_CNTL); 185 out_be32(&ddr->ddr_zq_cntl, DDR_DDR_ZQ_CNTL); 186 187 out_be32(&ddr->cs0_config_2, DDR_CS0_CONFIG_2); 188 189 /* DDR erratum A-009942 */ 190 tmp = in_be32(&ddr->debug[28]); 191 out_be32(&ddr->debug[28], tmp | 0x0070006f); 192 193 udelay(1); 194 195 #ifdef CONFIG_DEEP_SLEEP 196 if (is_warm_boot()) { 197 /* enter self-refresh */ 198 temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2); 199 temp_sdram_cfg |= SDRAM_CFG2_FRC_SR; 200 out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg); 201 202 temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN | SDRAM_CFG_BI); 203 } else 204 #endif 205 temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN & ~SDRAM_CFG_BI); 206 207 out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG | temp_sdram_cfg); 208 209 #ifdef CONFIG_DEEP_SLEEP 210 if (is_warm_boot()) { 211 /* exit self-refresh */ 212 temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2); 213 temp_sdram_cfg &= ~SDRAM_CFG2_FRC_SR; 214 out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg); 215 } 216 #endif 217 } 218 219 int dram_init(void) 220 { 221 #if (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)) 222 ddrmc_init(); 223 #endif 224 225 gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); 226 227 #if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD) 228 fsl_dp_resume(); 229 #endif 230 231 return 0; 232 } 233 234 #ifdef CONFIG_FSL_ESDHC 235 struct fsl_esdhc_cfg esdhc_cfg[1] = { 236 {CONFIG_SYS_FSL_ESDHC_ADDR}, 237 }; 238 239 int board_mmc_init(bd_t *bis) 240 { 241 esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 242 243 return fsl_esdhc_initialize(bis, &esdhc_cfg[0]); 244 } 245 #endif 246 247 int board_eth_init(bd_t *bis) 248 { 249 #ifdef CONFIG_TSEC_ENET 250 struct fsl_pq_mdio_info mdio_info; 251 struct tsec_info_struct tsec_info[4]; 252 int num = 0; 253 254 #ifdef CONFIG_TSEC1 255 SET_STD_TSEC_INFO(tsec_info[num], 1); 256 if (is_serdes_configured(SGMII_TSEC1)) { 257 puts("eTSEC1 is in sgmii mode.\n"); 258 tsec_info[num].flags |= TSEC_SGMII; 259 } 260 num++; 261 #endif 262 #ifdef CONFIG_TSEC2 263 SET_STD_TSEC_INFO(tsec_info[num], 2); 264 if (is_serdes_configured(SGMII_TSEC2)) { 265 puts("eTSEC2 is in sgmii mode.\n"); 266 tsec_info[num].flags |= TSEC_SGMII; 267 } 268 num++; 269 #endif 270 #ifdef CONFIG_TSEC3 271 SET_STD_TSEC_INFO(tsec_info[num], 3); 272 tsec_info[num].interface = PHY_INTERFACE_MODE_RGMII_ID; 273 num++; 274 #endif 275 if (!num) { 276 printf("No TSECs initialized\n"); 277 return 0; 278 } 279 280 mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; 281 mdio_info.name = DEFAULT_MII_NAME; 282 fsl_pq_mdio_init(bis, &mdio_info); 283 284 tsec_eth_init(bis, tsec_info, num); 285 #endif 286 287 return pci_eth_init(bis); 288 } 289 290 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 291 static void convert_serdes_mux(int type, int need_reset) 292 { 293 char current_serdes; 294 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 295 296 current_serdes = cpld_data->serdes_mux; 297 298 switch (type) { 299 case LANEB_SATA: 300 current_serdes &= ~MASK_LANE_B; 301 break; 302 case LANEB_SGMII1: 303 current_serdes |= (MASK_LANE_B | MASK_SGMII | MASK_LANE_C); 304 break; 305 case LANEC_SGMII1: 306 current_serdes &= ~(MASK_LANE_B | MASK_SGMII | MASK_LANE_C); 307 break; 308 case LANED_SGMII2: 309 current_serdes |= MASK_LANE_D; 310 break; 311 case LANEC_PCIEX1: 312 current_serdes |= MASK_LANE_C; 313 break; 314 case (LANED_PCIEX2 | LANEC_PCIEX1): 315 current_serdes |= MASK_LANE_C; 316 current_serdes &= ~MASK_LANE_D; 317 break; 318 default: 319 printf("CPLD serdes MUX: unsupported MUX type 0x%x\n", type); 320 return; 321 } 322 323 cpld_data->soft_mux_on |= CPLD_SET_MUX_SERDES; 324 cpld_data->serdes_mux = current_serdes; 325 326 if (need_reset == 1) { 327 printf("Reset board to enable configuration\n"); 328 cpld_data->system_rst = CONFIG_RESET; 329 } 330 } 331 332 int config_serdes_mux(void) 333 { 334 struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); 335 u32 protocol = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK; 336 337 protocol >>= RCWSR4_SRDS1_PRTCL_SHIFT; 338 switch (protocol) { 339 case 0x10: 340 convert_serdes_mux(LANEB_SATA, KEEP_STATUS); 341 convert_serdes_mux(LANED_PCIEX2 | 342 LANEC_PCIEX1, KEEP_STATUS); 343 break; 344 case 0x20: 345 convert_serdes_mux(LANEB_SGMII1, KEEP_STATUS); 346 convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS); 347 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); 348 break; 349 case 0x30: 350 convert_serdes_mux(LANEB_SATA, KEEP_STATUS); 351 convert_serdes_mux(LANEC_SGMII1, KEEP_STATUS); 352 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); 353 break; 354 case 0x70: 355 convert_serdes_mux(LANEB_SATA, KEEP_STATUS); 356 convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS); 357 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); 358 break; 359 } 360 361 return 0; 362 } 363 #endif 364 365 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 366 int config_board_mux(void) 367 { 368 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 369 int conflict_flag; 370 371 conflict_flag = 0; 372 if (hwconfig("i2c3")) { 373 conflict_flag++; 374 cpld_data->soft_mux_on |= SOFT_MUX_ON_I2C3_IFC; 375 cpld_data->i2c3_ifc_mux = PIN_I2C3_IFC_MUX_I2C3; 376 } 377 378 if (hwconfig("ifc")) { 379 conflict_flag++; 380 /* some signals can not enable simultaneous*/ 381 if (conflict_flag > 1) 382 goto conflict; 383 cpld_data->soft_mux_on |= SOFT_MUX_ON_I2C3_IFC; 384 cpld_data->i2c3_ifc_mux = PIN_I2C3_IFC_MUX_IFC; 385 } 386 387 conflict_flag = 0; 388 if (hwconfig("usb2")) { 389 conflict_flag++; 390 cpld_data->soft_mux_on |= SOFT_MUX_ON_CAN3_USB2; 391 cpld_data->can3_usb2_mux = PIN_CAN3_USB2_MUX_USB2; 392 } 393 394 if (hwconfig("can3")) { 395 conflict_flag++; 396 /* some signals can not enable simultaneous*/ 397 if (conflict_flag > 1) 398 goto conflict; 399 cpld_data->soft_mux_on |= SOFT_MUX_ON_CAN3_USB2; 400 cpld_data->can3_usb2_mux = PIN_CAN3_USB2_MUX_CAN3; 401 } 402 403 conflict_flag = 0; 404 if (hwconfig("lcd")) { 405 conflict_flag++; 406 cpld_data->soft_mux_on |= SOFT_MUX_ON_QE_LCD; 407 cpld_data->qe_lcd_mux = PIN_QE_LCD_MUX_LCD; 408 } 409 410 if (hwconfig("qe")) { 411 conflict_flag++; 412 /* some signals can not enable simultaneous*/ 413 if (conflict_flag > 1) 414 goto conflict; 415 cpld_data->soft_mux_on |= SOFT_MUX_ON_QE_LCD; 416 cpld_data->qe_lcd_mux = PIN_QE_LCD_MUX_QE; 417 } 418 419 return 0; 420 421 conflict: 422 printf("WARNING: pin conflict! MUX setting may failed!\n"); 423 return 0; 424 } 425 #endif 426 427 int board_early_init_f(void) 428 { 429 struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; 430 431 #ifdef CONFIG_TSEC_ENET 432 /* clear BD & FR bits for BE BD's and frame data */ 433 clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); 434 out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); 435 #endif 436 437 #ifdef CONFIG_FSL_IFC 438 init_early_memctl_regs(); 439 #endif 440 441 arch_soc_init(); 442 443 #if defined(CONFIG_DEEP_SLEEP) 444 if (is_warm_boot()) { 445 timer_init(); 446 dram_init(); 447 } 448 #endif 449 450 return 0; 451 } 452 453 #ifdef CONFIG_SPL_BUILD 454 void board_init_f(ulong dummy) 455 { 456 void (*second_uboot)(void); 457 458 /* Clear the BSS */ 459 memset(__bss_start, 0, __bss_end - __bss_start); 460 461 get_clocks(); 462 463 #if defined(CONFIG_DEEP_SLEEP) 464 if (is_warm_boot()) 465 fsl_dp_disable_console(); 466 #endif 467 468 preloader_console_init(); 469 470 timer_init(); 471 dram_init(); 472 473 /* Allow OCRAM access permission as R/W */ 474 #ifdef CONFIG_LAYERSCAPE_NS_ACCESS 475 enable_layerscape_ns_access(); 476 #endif 477 478 /* 479 * if it is woken up from deep sleep, then jump to second 480 * stage uboot and continue executing without recopying 481 * it from SD since it has already been reserved in memeory 482 * in last boot. 483 */ 484 if (is_warm_boot()) { 485 second_uboot = (void (*)(void))CONFIG_SYS_TEXT_BASE; 486 second_uboot(); 487 } 488 489 board_init_r(NULL, 0); 490 } 491 #endif 492 493 #ifdef CONFIG_DEEP_SLEEP 494 /* program the regulator (MC34VR500) to support deep sleep */ 495 void ls1twr_program_regulator(void) 496 { 497 unsigned int i2c_bus; 498 u8 i2c_device_id; 499 500 #define LS1TWR_I2C_BUS_MC34VR500 1 501 #define MC34VR500_ADDR 0x8 502 #define MC34VR500_DEVICEID 0x4 503 #define MC34VR500_DEVICEID_MASK 0x0f 504 505 i2c_bus = i2c_get_bus_num(); 506 i2c_set_bus_num(LS1TWR_I2C_BUS_MC34VR500); 507 i2c_device_id = i2c_reg_read(MC34VR500_ADDR, 0x0) & 508 MC34VR500_DEVICEID_MASK; 509 if (i2c_device_id != MC34VR500_DEVICEID) { 510 printf("The regulator (MC34VR500) does not exist. The device does not support deep sleep.\n"); 511 return; 512 } 513 514 i2c_reg_write(MC34VR500_ADDR, 0x31, 0x4); 515 i2c_reg_write(MC34VR500_ADDR, 0x4d, 0x4); 516 i2c_reg_write(MC34VR500_ADDR, 0x6d, 0x38); 517 i2c_reg_write(MC34VR500_ADDR, 0x6f, 0x37); 518 i2c_reg_write(MC34VR500_ADDR, 0x71, 0x30); 519 520 i2c_set_bus_num(i2c_bus); 521 } 522 #endif 523 524 int board_init(void) 525 { 526 #ifdef CONFIG_SYS_FSL_ERRATUM_A010315 527 erratum_a010315(); 528 #endif 529 530 #ifndef CONFIG_SYS_FSL_NO_SERDES 531 fsl_serdes_init(); 532 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 533 config_serdes_mux(); 534 #endif 535 #endif 536 537 ls102xa_smmu_stream_id_init(); 538 539 #ifdef CONFIG_U_QE 540 u_qe_init(); 541 #endif 542 543 #ifdef CONFIG_DEEP_SLEEP 544 ls1twr_program_regulator(); 545 #endif 546 return 0; 547 } 548 549 #if defined(CONFIG_SPL_BUILD) 550 void spl_board_init(void) 551 { 552 ls102xa_smmu_stream_id_init(); 553 } 554 #endif 555 556 #ifdef CONFIG_BOARD_LATE_INIT 557 int board_late_init(void) 558 { 559 #ifdef CONFIG_CHAIN_OF_TRUST 560 fsl_setenv_chain_of_trust(); 561 #endif 562 563 return 0; 564 } 565 #endif 566 567 #if defined(CONFIG_MISC_INIT_R) 568 int misc_init_r(void) 569 { 570 #ifdef CONFIG_FSL_DEVICE_DISABLE 571 device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl)); 572 #endif 573 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 574 config_board_mux(); 575 #endif 576 577 #ifdef CONFIG_FSL_CAAM 578 return sec_init(); 579 #endif 580 } 581 #endif 582 583 #if defined(CONFIG_DEEP_SLEEP) 584 void board_sleep_prepare(void) 585 { 586 #ifdef CONFIG_LAYERSCAPE_NS_ACCESS 587 enable_layerscape_ns_access(); 588 #endif 589 } 590 #endif 591 592 int ft_board_setup(void *blob, bd_t *bd) 593 { 594 ft_cpu_setup(blob, bd); 595 596 #ifdef CONFIG_PCI 597 ft_pci_setup(blob, bd); 598 #endif 599 600 return 0; 601 } 602 603 u8 flash_read8(void *addr) 604 { 605 return __raw_readb(addr + 1); 606 } 607 608 void flash_write16(u16 val, void *addr) 609 { 610 u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00)); 611 612 __raw_writew(shftval, addr); 613 } 614 615 u16 flash_read16(void *addr) 616 { 617 u16 val = __raw_readw(addr); 618 619 return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00); 620 } 621 622 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) \ 623 && !defined(CONFIG_SPL_BUILD) 624 static void convert_flash_bank(char bank) 625 { 626 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 627 628 printf("Now switch to boot from flash bank %d.\n", bank); 629 cpld_data->soft_mux_on = CPLD_SET_BOOT_BANK; 630 cpld_data->vbank = bank; 631 632 printf("Reset board to enable configuration.\n"); 633 cpld_data->system_rst = CONFIG_RESET; 634 } 635 636 static int flash_bank_cmd(cmd_tbl_t *cmdtp, int flag, int argc, 637 char * const argv[]) 638 { 639 if (argc != 2) 640 return CMD_RET_USAGE; 641 if (strcmp(argv[1], "0") == 0) 642 convert_flash_bank(BOOT_FROM_UPPER_BANK); 643 else if (strcmp(argv[1], "1") == 0) 644 convert_flash_bank(BOOT_FROM_LOWER_BANK); 645 else 646 return CMD_RET_USAGE; 647 648 return 0; 649 } 650 651 U_BOOT_CMD( 652 boot_bank, 2, 0, flash_bank_cmd, 653 "Flash bank Selection Control", 654 "bank[0-upper bank/1-lower bank] (e.g. boot_bank 0)" 655 ); 656 657 static int cpld_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, 658 char * const argv[]) 659 { 660 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 661 662 if (argc > 2) 663 return CMD_RET_USAGE; 664 if ((argc == 1) || (strcmp(argv[1], "conf") == 0)) 665 cpld_data->system_rst = CONFIG_RESET; 666 else if (strcmp(argv[1], "init") == 0) 667 cpld_data->global_rst = INIT_RESET; 668 else 669 return CMD_RET_USAGE; 670 671 return 0; 672 } 673 674 U_BOOT_CMD( 675 cpld_reset, 2, 0, cpld_reset_cmd, 676 "Reset via CPLD", 677 "conf\n" 678 " -reset with current CPLD configuration\n" 679 "init\n" 680 " -reset and initial CPLD configuration with default value" 681 682 ); 683 684 static void print_serdes_mux(void) 685 { 686 char current_serdes; 687 struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); 688 689 current_serdes = cpld_data->serdes_mux; 690 691 printf("Serdes Lane B: "); 692 if ((current_serdes & MASK_LANE_B) == 0) 693 printf("SATA,\n"); 694 else 695 printf("SGMII 1,\n"); 696 697 printf("Serdes Lane C: "); 698 if ((current_serdes & MASK_LANE_C) == 0) 699 printf("SGMII 1,\n"); 700 else 701 printf("PCIe,\n"); 702 703 printf("Serdes Lane D: "); 704 if ((current_serdes & MASK_LANE_D) == 0) 705 printf("PCIe,\n"); 706 else 707 printf("SGMII 2,\n"); 708 709 printf("SGMII 1 is on lane "); 710 if ((current_serdes & MASK_SGMII) == 0) 711 printf("C.\n"); 712 else 713 printf("B.\n"); 714 } 715 716 static int serdes_mux_cmd(cmd_tbl_t *cmdtp, int flag, int argc, 717 char * const argv[]) 718 { 719 if (argc != 2) 720 return CMD_RET_USAGE; 721 if (strcmp(argv[1], "sata") == 0) { 722 printf("Set serdes lane B to SATA.\n"); 723 convert_serdes_mux(LANEB_SATA, NEED_RESET); 724 } else if (strcmp(argv[1], "sgmii1b") == 0) { 725 printf("Set serdes lane B to SGMII 1.\n"); 726 convert_serdes_mux(LANEB_SGMII1, NEED_RESET); 727 } else if (strcmp(argv[1], "sgmii1c") == 0) { 728 printf("Set serdes lane C to SGMII 1.\n"); 729 convert_serdes_mux(LANEC_SGMII1, NEED_RESET); 730 } else if (strcmp(argv[1], "sgmii2") == 0) { 731 printf("Set serdes lane D to SGMII 2.\n"); 732 convert_serdes_mux(LANED_SGMII2, NEED_RESET); 733 } else if (strcmp(argv[1], "pciex1") == 0) { 734 printf("Set serdes lane C to PCIe X1.\n"); 735 convert_serdes_mux(LANEC_PCIEX1, NEED_RESET); 736 } else if (strcmp(argv[1], "pciex2") == 0) { 737 printf("Set serdes lane C & lane D to PCIe X2.\n"); 738 convert_serdes_mux((LANED_PCIEX2 | LANEC_PCIEX1), NEED_RESET); 739 } else if (strcmp(argv[1], "show") == 0) { 740 print_serdes_mux(); 741 } else { 742 return CMD_RET_USAGE; 743 } 744 745 return 0; 746 } 747 748 U_BOOT_CMD( 749 lane_bank, 2, 0, serdes_mux_cmd, 750 "Multiplexed function setting for SerDes Lanes", 751 "sata\n" 752 " -change lane B to sata\n" 753 "lane_bank sgmii1b\n" 754 " -change lane B to SGMII1\n" 755 "lane_bank sgmii1c\n" 756 " -change lane C to SGMII1\n" 757 "lane_bank sgmii2\n" 758 " -change lane D to SGMII2\n" 759 "lane_bank pciex1\n" 760 " -change lane C to PCIeX1\n" 761 "lane_bank pciex2\n" 762 " -change lane C & lane D to PCIeX2\n" 763 "\nWARNING: If you aren't familiar with the setting of serdes, don't try to change anything!\n" 764 ); 765 #endif 766