1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <fsl_ddr_sdram.h> 9 #include <fsl_ddr_dimm_params.h> 10 #include "ddr.h" 11 12 DECLARE_GLOBAL_DATA_PTR; 13 14 void fsl_ddr_board_options(memctl_options_t *popts, 15 dimm_params_t *pdimm, 16 unsigned int ctrl_num) 17 { 18 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; 19 ulong ddr_freq; 20 21 if (ctrl_num > 3) { 22 printf("Not supported controller number %d\n", ctrl_num); 23 return; 24 } 25 if (!pdimm->n_ranks) 26 return; 27 28 pbsp = udimms[0]; 29 30 /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr 31 * freqency and n_banks specified in board_specific_parameters table. 32 */ 33 ddr_freq = get_ddr_freq(0) / 1000000; 34 while (pbsp->datarate_mhz_high) { 35 if (pbsp->n_ranks == pdimm->n_ranks) { 36 if (ddr_freq <= pbsp->datarate_mhz_high) { 37 popts->clk_adjust = pbsp->clk_adjust; 38 popts->wrlvl_start = pbsp->wrlvl_start; 39 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 40 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 41 popts->cpo_override = pbsp->cpo_override; 42 popts->write_data_delay = 43 pbsp->write_data_delay; 44 goto found; 45 } 46 pbsp_highest = pbsp; 47 } 48 pbsp++; 49 } 50 51 if (pbsp_highest) { 52 printf("Error: board specific timing not found for %lu MT/s\n", 53 ddr_freq); 54 printf("Trying to use the highest speed (%u) parameters\n", 55 pbsp_highest->datarate_mhz_high); 56 popts->clk_adjust = pbsp_highest->clk_adjust; 57 popts->wrlvl_start = pbsp_highest->wrlvl_start; 58 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; 59 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; 60 } else { 61 panic("DIMM is not supported by this board"); 62 } 63 found: 64 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", 65 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); 66 67 /* force DDR bus width to 32 bits */ 68 popts->data_bus_width = 1; 69 popts->otf_burst_chop_en = 0; 70 popts->burst_length = DDR_BL8; 71 72 /* 73 * Factors to consider for half-strength driver enable: 74 * - number of DIMMs installed 75 */ 76 popts->half_strength_driver_enable = 1; 77 /* 78 * Write leveling override 79 */ 80 popts->wrlvl_override = 1; 81 popts->wrlvl_sample = 0xf; 82 83 /* 84 * Rtt and Rtt_WR override 85 */ 86 popts->rtt_override = 0; 87 88 /* Enable ZQ calibration */ 89 popts->zq_en = 1; 90 91 #ifdef CONFIG_SYS_FSL_DDR4 92 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm); 93 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) | 94 DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */ 95 #else 96 popts->cswl_override = DDR_CSWL_CS0; 97 98 /* DHC_EN =1, ODT = 75 Ohm */ 99 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); 100 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); 101 #endif 102 } 103 104 #ifdef CONFIG_SYS_DDR_RAW_TIMING 105 dimm_params_t ddr_raw_timing = { 106 .n_ranks = 1, 107 .rank_density = 1073741824u, 108 .capacity = 1073741824u, 109 .primary_sdram_width = 32, 110 .ec_sdram_width = 0, 111 .registered_dimm = 0, 112 .mirrored_dimm = 0, 113 .n_row_addr = 15, 114 .n_col_addr = 10, 115 .n_banks_per_sdram_device = 8, 116 .edc_config = 0, 117 .burst_lengths_bitmask = 0x0c, 118 119 .tckmin_x_ps = 1071, 120 .caslat_x = 0xfe << 4, /* 5,6,7,8 */ 121 .taa_ps = 13125, 122 .twr_ps = 15000, 123 .trcd_ps = 13125, 124 .trrd_ps = 7500, 125 .trp_ps = 13125, 126 .tras_ps = 37500, 127 .trc_ps = 50625, 128 .trfc_ps = 160000, 129 .twtr_ps = 7500, 130 .trtp_ps = 7500, 131 .refresh_rate_ps = 7800000, 132 .tfaw_ps = 37500, 133 }; 134 135 int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, 136 unsigned int controller_number, 137 unsigned int dimm_number) 138 { 139 static const char dimm_model[] = "Fixed DDR on board"; 140 141 if (((controller_number == 0) && (dimm_number == 0)) || 142 ((controller_number == 1) && (dimm_number == 0))) { 143 memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); 144 memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); 145 memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); 146 } 147 148 return 0; 149 } 150 #endif 151 152 phys_size_t initdram(int board_type) 153 { 154 phys_size_t dram_size; 155 156 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL) 157 puts("Initializing DDR....using SPD\n"); 158 dram_size = fsl_ddr_sdram(); 159 #else 160 dram_size = fsl_ddr_sdram_size(); 161 #endif 162 return dram_size; 163 } 164 165 void dram_init_banksize(void) 166 { 167 gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; 168 gd->bd->bi_dram[0].size = gd->ram_size; 169 } 170