1Overview
2--------
3QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
4development platform, with a complete debugging environment.
5The LS1012ARDB board supports the QorIQ LS1012A processor and is
6optimized to support the high-bandwidth DDR3L memory and
7a full complement of high-speed SerDes ports.
8
9LS1012A SoC Overview
10--------------------
11Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A
12SoC overview.
13
14LS1012ARDB board Overview
15-----------------------
16 - SERDES Connections, 4 lanes supporting:
17      - PCI Express - 3.0
18      - SGMII, SGMII 2.5
19      - SATA 3.0
20 - DDR Controller
21     - 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
22 -QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
23 signals to
24    - QSPI NOR flash memory (2 virtual banks)
25    - the QSPI emulator.s
26 - USB 3.0
27    - one high-speed USB 2.0/3.0 port.
28 - Two enhanced secure digital host controllers:
29    - SDHC1 controller can be connected to onboard SDHC connector
30    - SDHC2 controller: Three dual 1:4 mux/demux devices,
31    74CBTLV3253DS (U30, U31, U33) drive the SDHC2 signals to eMMC,
32    SDIO WiFi, SPI, and Ardiuno shield
33 - 2 I2C controllers
34 - One SATA onboard connectors
35 - UART
36   - The LS1012A processor consists of two UART controllers,
37   out of which only UART1 is used on RDB.
38 - ARM JTAG support
39
40Booting Options
41---------------
42a) QSPI Flash Emu Boot
43b) QSPI Flash 1
44c) QSPI Flash 2
45
46QSPI flash map
47--------------
48Images		| Size	|QSPI Flash Address
49------------------------------------------
50RCW + PBI	| 1MB	| 0x4000_0000
51U-boot 		| 1MB	| 0x4010_0000
52U-boot Env 	| 1MB	| 0x4020_0000
53PPA FIT image	| 2MB	| 0x4050_0000
54Linux ITB	| ~53MB | 0x40A0_0000
55
56LS1012A2G5RDB board Overview
57-----------------------
58 - SERDES Connections, 3 lanes supporting:
59      - SGMII, SGMII 2.5
60      - SATA 3.0
61 - DDR Controller
62     - 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
63 -QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
64 signals to
65    - QSPI NOR flash memory
66 - USB 3.0
67    - one high-speed USB 2.0/3.0 port.
68 - SDIO WiFi, SPI
69 - 2 I2C controllers
70 - One SATA onboard connectors
71 - UART
72   - The LS1012A processor consists of two UART controllers,
73   out of which only UART1 is used on 2G5RDB.
74 - ARM JTAG support
75
76Major Difference between LS1012ARDB and LS1012A-2G5RDB
77------------------------------------------------------
781. LS1012A-2G5RDB has Type C USB connector unlike USB Type A/B of LS1012ARDB
792. LS1012A-2G5RDB has 2 2.5G AQR PHY unlike 2 1G Realtek RTL8211FS PHYs
80   of LS1012ARDB
813. LS1012A-2G5RDB is not having Arduino header
824. LS1012A-2G5RDB doesn't have PCI slot
83
84Booting Options
85---------------
86QSPI Flash
87
88QSPI flash map
89--------------
90Images		| Size	|QSPI Flash Address
91------------------------------------------
92RCW + PBI	| 1MB	| 0x4000_0000
93U-boot 		| 1MB	| 0x4010_0000
94U-boot Env 	| 1MB	| 0x4030_0000
95PPA FIT image	| 2MB	| 0x4040_0000
96PFE firmware	| 20K	| 0x00a0_0000
97Linux ITB	| ~53MB | 0x4100_0000
98