1 /* 2 * Copyright 2009-2011 Freescale Semiconductor, Inc. 3 * Author: Timur Tabi <timur@freescale.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * This file handles the board muxing between the Fman Ethernet MACs and 10 * the RGMII/SGMII/XGMII PHYs on a Freescale P3041/P5020 "Hydra" reference 11 * board. The RGMII PHYs are the two on-board 1Gb ports. The SGMII PHYs are 12 * provided by the standard Freescale four-port SGMII riser card. The 10Gb 13 * XGMII PHY is provided via the XAUI riser card. Since there is only one 14 * Fman device on a P3041 and P5020, we only support one SGMII card and one 15 * RGMII card. 16 * 17 * Muxing is handled via the PIXIS BRDCFG1 register. The EMI1 bits control 18 * muxing among the RGMII PHYs and the SGMII PHYs. The value for RGMII is 19 * always the same (0). The value for SGMII depends on which slot the riser is 20 * inserted in. The EMI2 bits control muxing for the the XGMII. Like SGMII, 21 * the value is based on which slot the XAUI is inserted in. 22 * 23 * The SERDES configuration is used to determine where the SGMII and XAUI cards 24 * exist, and also which Fman MACs are routed to which PHYs. So for a given 25 * Fman MAC, there is one and only PHY it connects to. MACs cannot be routed 26 * to PHYs dynamically. 27 * 28 * 29 * This file also updates the device tree in three ways: 30 * 31 * 1) The status of each virtual MDIO node that is referenced by an Ethernet 32 * node is set to "okay". 33 * 34 * 2) The phy-handle property of each active Ethernet MAC node is set to the 35 * appropriate PHY node. 36 * 37 * 3) The "mux value" for each virtual MDIO node is set to the correct value, 38 * if necessary. Some virtual MDIO nodes do not have configurable mux 39 * values, so those values are hard-coded in the DTS. On the HYDRA board, 40 * the virtual MDIO node for the SGMII card needs to be updated. 41 * 42 * For all this to work, the device tree needs to have the following: 43 * 44 * 1) An alias for each PHY node that an Ethernet node could be routed to. 45 * 46 * 2) An alias for each real and virtual MDIO node that is disabled by default 47 * and might need to be enabled, and also might need to have its mux-value 48 * updated. 49 */ 50 51 #include <common.h> 52 #include <netdev.h> 53 #include <asm/fsl_serdes.h> 54 #include <fm_eth.h> 55 #include <fsl_mdio.h> 56 #include <malloc.h> 57 #include <fdt_support.h> 58 #include <asm/fsl_dtsec.h> 59 60 #include "../common/ngpixis.h" 61 #include "../common/fman.h" 62 63 #ifdef CONFIG_FMAN_ENET 64 65 #define BRDCFG1_EMI1_SEL_MASK 0x78 66 #define BRDCFG1_EMI1_SEL_SLOT1 0x10 67 #define BRDCFG1_EMI1_SEL_SLOT2 0x20 68 #define BRDCFG1_EMI1_SEL_SLOT5 0x30 69 #define BRDCFG1_EMI1_SEL_SLOT6 0x40 70 #define BRDCFG1_EMI1_SEL_SLOT7 0x50 71 #define BRDCFG1_EMI1_SEL_RGMII 0x00 72 #define BRDCFG1_EMI1_EN 0x08 73 #define BRDCFG1_EMI2_SEL_MASK 0x06 74 #define BRDCFG1_EMI2_SEL_SLOT1 0x00 75 #define BRDCFG1_EMI2_SEL_SLOT2 0x02 76 77 #define BRDCFG2_REG_GPIO_SEL 0x20 78 79 #define PHY_BASE_ADDR 0x00 80 81 /* 82 * BRDCFG1 mask and value for each MAC 83 * 84 * This array contains the BRDCFG1 values (in mask/val format) that route the 85 * MDIO bus to a particular RGMII or SGMII PHY. 86 */ 87 struct { 88 u8 mask; 89 u8 val; 90 } mdio_mux[NUM_FM_PORTS]; 91 92 /* 93 * Mapping of all 18 SERDES lanes to board slots. A value of '0' here means 94 * that the mapping must be determined dynamically, or that the lane maps to 95 * something other than a board slot 96 */ 97 static u8 lane_to_slot[] = { 98 7, 7, 0, 0, 0, 0, 0, 0, 0, 0, 2, 2, 2, 2, 1, 1, 0, 0 99 }; 100 101 /* 102 * Set the board muxing for a given MAC 103 * 104 * The MDIO layer calls this function every time it wants to talk to a PHY. 105 */ 106 void hydra_mux_mdio(u8 mask, u8 val) 107 { 108 clrsetbits_8(&pixis->brdcfg1, mask, val); 109 } 110 111 struct hydra_mdio { 112 u8 mask; 113 u8 val; 114 struct mii_dev *realbus; 115 }; 116 117 static int hydra_mdio_read(struct mii_dev *bus, int addr, int devad, 118 int regnum) 119 { 120 struct hydra_mdio *priv = bus->priv; 121 122 hydra_mux_mdio(priv->mask, priv->val); 123 124 return priv->realbus->read(priv->realbus, addr, devad, regnum); 125 } 126 127 static int hydra_mdio_write(struct mii_dev *bus, int addr, int devad, 128 int regnum, u16 value) 129 { 130 struct hydra_mdio *priv = bus->priv; 131 132 hydra_mux_mdio(priv->mask, priv->val); 133 134 return priv->realbus->write(priv->realbus, addr, devad, regnum, value); 135 } 136 137 static int hydra_mdio_reset(struct mii_dev *bus) 138 { 139 struct hydra_mdio *priv = bus->priv; 140 141 return priv->realbus->reset(priv->realbus); 142 } 143 144 static void hydra_mdio_set_mux(char *name, u8 mask, u8 val) 145 { 146 struct mii_dev *bus = miiphy_get_dev_by_name(name); 147 struct hydra_mdio *priv = bus->priv; 148 149 priv->mask = mask; 150 priv->val = val; 151 } 152 153 static int hydra_mdio_init(char *realbusname, char *fakebusname) 154 { 155 struct hydra_mdio *hmdio; 156 struct mii_dev *bus = mdio_alloc(); 157 158 if (!bus) { 159 printf("Failed to allocate Hydra MDIO bus\n"); 160 return -1; 161 } 162 163 hmdio = malloc(sizeof(*hmdio)); 164 if (!hmdio) { 165 printf("Failed to allocate Hydra private data\n"); 166 free(bus); 167 return -1; 168 } 169 170 bus->read = hydra_mdio_read; 171 bus->write = hydra_mdio_write; 172 bus->reset = hydra_mdio_reset; 173 sprintf(bus->name, fakebusname); 174 175 hmdio->realbus = miiphy_get_dev_by_name(realbusname); 176 177 if (!hmdio->realbus) { 178 printf("No bus with name %s\n", realbusname); 179 free(bus); 180 free(hmdio); 181 return -1; 182 } 183 184 bus->priv = hmdio; 185 186 return mdio_register(bus); 187 } 188 189 /* 190 * Given an alias or a path for a node, set the mux value of that node. 191 * 192 * If 'alias' is not a valid alias, then it is treated as a full path to the 193 * node. No error checking is performed. 194 * 195 * This function is normally called to set the fsl,hydra-mdio-muxval property 196 * of a virtual MDIO node. 197 */ 198 static void fdt_set_mdio_mux(void *fdt, const char *alias, u32 mux) 199 { 200 const char *path = fdt_get_alias(fdt, alias); 201 202 if (!path) 203 path = alias; 204 205 do_fixup_by_path(fdt, path, "reg", 206 &mux, sizeof(mux), 1); 207 do_fixup_by_path(fdt, path, "fsl,hydra-mdio-muxval", 208 &mux, sizeof(mux), 1); 209 } 210 211 /* 212 * Given the following ... 213 * 214 * 1) A pointer to an Fman Ethernet node (as identified by the 'compat' 215 * compatible string and 'addr' physical address) 216 * 217 * 2) An Fman port 218 * 219 * ... update the phy-handle property of the Ethernet node to point to the 220 * right PHY. This assumes that we already know the PHY for each port. That 221 * information is stored in mdio_mux[]. 222 * 223 * The offset of the Fman Ethernet node is also passed in for convenience, but 224 * it is not used, and we recalculate the offset anyway. 225 * 226 * Note that what we call "Fman ports" (enum fm_port) is really an Fman MAC. 227 * Inside the Fman, "ports" are things that connect to MACs. We only call them 228 * ports in U-Boot because on previous Ethernet devices (e.g. Gianfar), MACs 229 * and ports are the same thing. 230 * 231 * Note that this code would be cleaner if had a function called 232 * fm_info_get_phy_address(), which returns a value from the fm1_dtsec_info[] 233 * array. That's because all we're doing is figuring out the PHY address for 234 * a given Fman MAC and writing it to the device tree. Well, we already did 235 * the hard work to figure that out in board_eth_init(), so it's silly to 236 * repeat that here. 237 */ 238 void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, 239 enum fm_port port, int offset) 240 { 241 unsigned int mux = mdio_mux[port].val & mdio_mux[port].mask; 242 char phy[16]; 243 244 if (port == FM1_10GEC1) { 245 /* XAUI */ 246 int lane = serdes_get_first_lane(XAUI_FM1); 247 if (lane >= 0) { 248 /* The XAUI PHY is identified by the slot */ 249 sprintf(phy, "phy_xgmii_%u", lane_to_slot[lane]); 250 fdt_set_phy_handle(fdt, compat, addr, phy); 251 } 252 return; 253 } 254 255 if (mux == (BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN)) { 256 /* RGMII */ 257 /* The RGMII PHY is identified by the MAC connected to it */ 258 sprintf(phy, "phy_rgmii_%u", port == FM1_DTSEC4 ? 0 : 1); 259 fdt_set_phy_handle(fdt, compat, addr, phy); 260 return; 261 } 262 263 /* If it's not RGMII or XGMII, it must be SGMII */ 264 if (mux) { 265 /* The SGMII PHY is identified by the MAC connected to it */ 266 sprintf(phy, "phy_sgmii_%x", 267 CONFIG_SYS_FM1_DTSEC1_PHY_ADDR + (port - FM1_DTSEC1)); 268 fdt_set_phy_handle(fdt, compat, addr, phy); 269 } 270 } 271 272 #define PIXIS_SW2_LANE_23_SEL 0x80 273 #define PIXIS_SW2_LANE_45_SEL 0x40 274 #define PIXIS_SW2_LANE_67_SEL_MASK 0x30 275 #define PIXIS_SW2_LANE_67_SEL_5 0x00 276 #define PIXIS_SW2_LANE_67_SEL_6 0x20 277 #define PIXIS_SW2_LANE_67_SEL_7 0x10 278 #define PIXIS_SW2_LANE_8_SEL 0x08 279 #define PIXIS_SW2_LANE_1617_SEL 0x04 280 281 /* 282 * Initialize the lane_to_slot[] array. 283 * 284 * On the P4080DS "Expedition" board, the mapping of SERDES lanes to board 285 * slots is hard-coded. On the Hydra board, however, the mapping is controlled 286 * by board switch SW2, so the lane_to_slot[] array needs to be dynamically 287 * initialized. 288 */ 289 static void initialize_lane_to_slot(void) 290 { 291 u8 sw2 = in_8(&PIXIS_SW(2)); 292 293 lane_to_slot[2] = (sw2 & PIXIS_SW2_LANE_23_SEL) ? 7 : 4; 294 lane_to_slot[3] = lane_to_slot[2]; 295 296 lane_to_slot[4] = (sw2 & PIXIS_SW2_LANE_45_SEL) ? 7 : 6; 297 lane_to_slot[5] = lane_to_slot[4]; 298 299 switch (sw2 & PIXIS_SW2_LANE_67_SEL_MASK) { 300 case PIXIS_SW2_LANE_67_SEL_5: 301 lane_to_slot[6] = 5; 302 break; 303 case PIXIS_SW2_LANE_67_SEL_6: 304 lane_to_slot[6] = 6; 305 break; 306 case PIXIS_SW2_LANE_67_SEL_7: 307 lane_to_slot[6] = 7; 308 break; 309 } 310 lane_to_slot[7] = lane_to_slot[6]; 311 312 lane_to_slot[8] = (sw2 & PIXIS_SW2_LANE_8_SEL) ? 3 : 0; 313 314 lane_to_slot[16] = (sw2 & PIXIS_SW2_LANE_1617_SEL) ? 1 : 0; 315 lane_to_slot[17] = lane_to_slot[16]; 316 } 317 318 #endif /* #ifdef CONFIG_FMAN_ENET */ 319 320 /* 321 * Configure the status for the virtual MDIO nodes 322 * 323 * Rather than create the virtual MDIO nodes from scratch for each active 324 * virtual MDIO, we expect the DTS to have the nodes defined already, and we 325 * only enable the ones that are actually active. 326 * 327 * We assume that the DTS already hard-codes the status for all the 328 * virtual MDIO nodes to "disabled", so all we need to do is enable the 329 * active ones. 330 * 331 * For SGMII, we also need to set the mux value in the node. 332 */ 333 void fdt_fixup_board_enet(void *fdt) 334 { 335 #ifdef CONFIG_FMAN_ENET 336 unsigned int i; 337 int lane; 338 339 for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { 340 int idx = i - FM1_DTSEC1; 341 342 switch (fm_info_get_enet_if(i)) { 343 case PHY_INTERFACE_MODE_SGMII: 344 lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx); 345 if (lane >= 0) { 346 fdt_status_okay_by_alias(fdt, "emi1_sgmii"); 347 /* Also set the MUX value */ 348 fdt_set_mdio_mux(fdt, "emi1_sgmii", 349 mdio_mux[i].val); 350 } 351 break; 352 case PHY_INTERFACE_MODE_RGMII: 353 fdt_status_okay_by_alias(fdt, "emi1_rgmii"); 354 break; 355 default: 356 break; 357 } 358 } 359 360 lane = serdes_get_first_lane(XAUI_FM1); 361 if (lane >= 0) 362 fdt_status_okay_by_alias(fdt, "emi2_xgmii"); 363 #endif 364 } 365 366 int board_eth_init(bd_t *bis) 367 { 368 #ifdef CONFIG_FMAN_ENET 369 struct fsl_pq_mdio_info dtsec_mdio_info; 370 struct tgec_mdio_info tgec_mdio_info; 371 unsigned int i, slot; 372 int lane; 373 struct mii_dev *bus; 374 375 printf("Initializing Fman\n"); 376 377 initialize_lane_to_slot(); 378 379 /* We want to use the PIXIS to configure MUX routing, not GPIOs. */ 380 setbits_8(&pixis->brdcfg2, BRDCFG2_REG_GPIO_SEL); 381 382 memset(mdio_mux, 0, sizeof(mdio_mux)); 383 384 dtsec_mdio_info.regs = 385 (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR; 386 dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; 387 388 /* Register the real 1G MDIO bus */ 389 fsl_pq_mdio_init(bis, &dtsec_mdio_info); 390 391 tgec_mdio_info.regs = 392 (struct tgec_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; 393 tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; 394 395 /* Register the real 10G MDIO bus */ 396 fm_tgec_mdio_init(bis, &tgec_mdio_info); 397 398 /* Register the three virtual MDIO front-ends */ 399 hydra_mdio_init(DEFAULT_FM_MDIO_NAME, "HYDRA_RGMII_MDIO"); 400 hydra_mdio_init(DEFAULT_FM_MDIO_NAME, "HYDRA_SGMII_MDIO"); 401 402 /* 403 * Program the DTSEC PHY addresses assuming that they are all SGMII. 404 * For any DTSEC that's RGMII, we'll override its PHY address later. 405 * We assume that DTSEC5 is only used for RGMII. 406 */ 407 fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR); 408 fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR); 409 fm_info_set_phy_address(FM1_DTSEC3, CONFIG_SYS_FM1_DTSEC3_PHY_ADDR); 410 fm_info_set_phy_address(FM1_DTSEC4, CONFIG_SYS_FM1_DTSEC4_PHY_ADDR); 411 412 for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { 413 int idx = i - FM1_DTSEC1; 414 415 switch (fm_info_get_enet_if(i)) { 416 case PHY_INTERFACE_MODE_SGMII: 417 lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx); 418 if (lane < 0) 419 break; 420 slot = lane_to_slot[lane]; 421 mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK; 422 switch (slot) { 423 case 1: 424 /* Always DTSEC5 on Bank 3 */ 425 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT1 | 426 BRDCFG1_EMI1_EN; 427 break; 428 case 2: 429 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT2 | 430 BRDCFG1_EMI1_EN; 431 break; 432 case 5: 433 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT5 | 434 BRDCFG1_EMI1_EN; 435 break; 436 case 6: 437 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT6 | 438 BRDCFG1_EMI1_EN; 439 break; 440 case 7: 441 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT7 | 442 BRDCFG1_EMI1_EN; 443 break; 444 }; 445 446 hydra_mdio_set_mux("HYDRA_SGMII_MDIO", 447 mdio_mux[i].mask, mdio_mux[i].val); 448 fm_info_set_mdio(i, 449 miiphy_get_dev_by_name("HYDRA_SGMII_MDIO")); 450 break; 451 case PHY_INTERFACE_MODE_RGMII: 452 /* 453 * If DTSEC4 is RGMII, then it's routed via via EC1 to 454 * the first on-board RGMII port. If DTSEC5 is RGMII, 455 * then it's routed via via EC2 to the second on-board 456 * RGMII port. The other DTSECs cannot be routed to 457 * RGMII. 458 */ 459 fm_info_set_phy_address(i, i == FM1_DTSEC4 ? 0 : 1); 460 mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK; 461 mdio_mux[i].val = BRDCFG1_EMI1_SEL_RGMII | 462 BRDCFG1_EMI1_EN; 463 hydra_mdio_set_mux("HYDRA_RGMII_MDIO", 464 mdio_mux[i].mask, mdio_mux[i].val); 465 fm_info_set_mdio(i, 466 miiphy_get_dev_by_name("HYDRA_RGMII_MDIO")); 467 break; 468 case PHY_INTERFACE_MODE_NONE: 469 fm_info_set_phy_address(i, 0); 470 break; 471 default: 472 printf("Fman1: DTSEC%u set to unknown interface %i\n", 473 idx + 1, fm_info_get_enet_if(i)); 474 fm_info_set_phy_address(i, 0); 475 break; 476 } 477 } 478 479 bus = miiphy_get_dev_by_name("HYDRA_SGMII_MDIO"); 480 set_sgmii_phy(bus, FM1_DTSEC1, CONFIG_SYS_NUM_FM1_DTSEC, PHY_BASE_ADDR); 481 482 /* 483 * For 10G, we only support one XAUI card per Fman. If present, then we 484 * force its routing and never touch those bits again, which removes the 485 * need for Linux to do any muxing. This works because of the way 486 * BRDCFG1 is defined, but it's a bit hackish. 487 * 488 * The PHY address for the XAUI card depends on which slot it's in. The 489 * macros we use imply that the PHY address is based on which FM, but 490 * that's not true. On the P4080DS, FM1 could only use XAUI in slot 5, 491 * and FM2 could only use a XAUI in slot 4. On the Hydra board, we 492 * check the actual slot and just use the macros as-is, even though 493 * the P3041 and P5020 only have one Fman. 494 */ 495 lane = serdes_get_first_lane(XAUI_FM1); 496 if (lane >= 0) { 497 slot = lane_to_slot[lane]; 498 if (slot == 1) { 499 /* XAUI card is in slot 1 */ 500 clrsetbits_8(&pixis->brdcfg1, BRDCFG1_EMI2_SEL_MASK, 501 BRDCFG1_EMI2_SEL_SLOT1); 502 fm_info_set_phy_address(FM1_10GEC1, 503 CONFIG_SYS_FM1_10GEC1_PHY_ADDR); 504 } else { 505 /* XAUI card is in slot 2 */ 506 clrsetbits_8(&pixis->brdcfg1, BRDCFG1_EMI2_SEL_MASK, 507 BRDCFG1_EMI2_SEL_SLOT2); 508 fm_info_set_phy_address(FM1_10GEC1, 509 CONFIG_SYS_FM2_10GEC1_PHY_ADDR); 510 } 511 } 512 513 fm_info_set_mdio(FM1_10GEC1, 514 miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME)); 515 516 cpu_eth_init(bis); 517 #endif 518 519 return pci_eth_init(bis); 520 } 521