1 /* 2 * Copyright 2009-2011 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0 5 */ 6 7 #include <common.h> 8 #include <i2c.h> 9 #include <hwconfig.h> 10 #include <asm/mmu.h> 11 #include <fsl_ddr_sdram.h> 12 #include <fsl_ddr_dimm_params.h> 13 #include <asm/fsl_law.h> 14 15 DECLARE_GLOBAL_DATA_PTR; 16 17 18 /* 19 * Fixed sdram init -- doesn't use serial presence detect. 20 */ 21 extern fixed_ddr_parm_t fixed_ddr_parm_0[]; 22 #if (CONFIG_NUM_DDR_CONTROLLERS == 2) 23 extern fixed_ddr_parm_t fixed_ddr_parm_1[]; 24 #endif 25 26 phys_size_t fixed_sdram(void) 27 { 28 int i; 29 char buf[32]; 30 fsl_ddr_cfg_regs_t ddr_cfg_regs; 31 phys_size_t ddr_size; 32 unsigned int lawbar1_target_id; 33 ulong ddr_freq, ddr_freq_mhz; 34 35 ddr_freq = get_ddr_freq(0); 36 ddr_freq_mhz = ddr_freq / 1000000; 37 38 printf("Configuring DDR for %s MT/s data rate\n", 39 strmhz(buf, ddr_freq)); 40 41 for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) { 42 if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) && 43 (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) { 44 memcpy(&ddr_cfg_regs, 45 fixed_ddr_parm_0[i].ddr_settings, 46 sizeof(ddr_cfg_regs)); 47 break; 48 } 49 } 50 51 if (fixed_ddr_parm_0[i].max_freq == 0) 52 panic("Unsupported DDR data rate %s MT/s data rate\n", 53 strmhz(buf, ddr_freq)); 54 55 ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; 56 ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN; 57 fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0); 58 59 #if (CONFIG_NUM_DDR_CONTROLLERS == 2) 60 memcpy(&ddr_cfg_regs, 61 fixed_ddr_parm_1[i].ddr_settings, 62 sizeof(ddr_cfg_regs)); 63 ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN; 64 fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 1, 0); 65 #endif 66 67 /* 68 * setup laws for DDR. If not interleaving, presuming half memory on 69 * DDR1 and the other half on DDR2 70 */ 71 if (fixed_ddr_parm_0[i].ddr_settings->cs[0].config & 0x20000000) { 72 if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, 73 ddr_size, 74 LAW_TRGT_IF_DDR_INTRLV) < 0) { 75 printf("ERROR setting Local Access Windows for DDR\n"); 76 return 0; 77 } 78 } else { 79 #if (CONFIG_NUM_DDR_CONTROLLERS == 2) 80 /* We require both controllers have identical DIMMs */ 81 lawbar1_target_id = LAW_TRGT_IF_DDR_1; 82 if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, 83 ddr_size / 2, 84 lawbar1_target_id) < 0) { 85 printf("ERROR setting Local Access Windows for DDR\n"); 86 return 0; 87 } 88 lawbar1_target_id = LAW_TRGT_IF_DDR_2; 89 if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE + ddr_size / 2, 90 ddr_size / 2, 91 lawbar1_target_id) < 0) { 92 printf("ERROR setting Local Access Windows for DDR\n"); 93 return 0; 94 } 95 #else 96 lawbar1_target_id = LAW_TRGT_IF_DDR_1; 97 if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, 98 ddr_size, 99 lawbar1_target_id) < 0) { 100 printf("ERROR setting Local Access Windows for DDR\n"); 101 return 0; 102 } 103 #endif 104 } 105 return ddr_size; 106 } 107 108 struct board_specific_parameters { 109 u32 n_ranks; 110 u32 datarate_mhz_high; 111 u32 clk_adjust; 112 u32 wrlvl_start; 113 u32 cpo; 114 u32 write_data_delay; 115 u32 force_2t; 116 }; 117 118 /* 119 * This table contains all valid speeds we want to override with board 120 * specific parameters. datarate_mhz_high values need to be in ascending order 121 * for each n_ranks group. 122 */ 123 static const struct board_specific_parameters udimm0[] = { 124 /* 125 * memory controller 0 126 * num| hi| clk| wrlvl | cpo |wrdata|2T 127 * ranks| mhz|adjst| start | |delay | 128 */ 129 {4, 850, 4, 6, 0xff, 2, 0}, 130 {4, 950, 5, 7, 0xff, 2, 0}, 131 {4, 1050, 5, 8, 0xff, 2, 0}, 132 {4, 1250, 5, 10, 0xff, 2, 0}, 133 {4, 1350, 5, 11, 0xff, 2, 0}, 134 {4, 1666, 5, 12, 0xff, 2, 0}, 135 {2, 850, 5, 6, 0xff, 2, 0}, 136 {2, 1050, 5, 7, 0xff, 2, 0}, 137 {2, 1250, 4, 6, 0xff, 2, 0}, 138 {2, 1350, 5, 7, 0xff, 2, 0}, 139 {2, 1666, 5, 8, 0xff, 2, 0}, 140 {1, 1250, 4, 6, 0xff, 2, 0}, 141 {1, 1335, 4, 7, 0xff, 2, 0}, 142 {1, 1666, 4, 8, 0xff, 2, 0}, 143 {} 144 }; 145 146 /* 147 * The two slots have slightly different timing. The center values are good 148 * for both slots. We use identical speed tables for them. In future use, if 149 * DIMMs have fewer center values that require two separated tables, copy the 150 * udimm0 table to udimm1 and make changes to clk_adjust and wrlvl_start. 151 */ 152 static const struct board_specific_parameters *udimms[] = { 153 udimm0, 154 udimm0, 155 }; 156 157 static const struct board_specific_parameters rdimm0[] = { 158 /* 159 * memory controller 0 160 * num| hi| clk| wrlvl | cpo |wrdata|2T 161 * ranks| mhz|adjst| start | |delay | 162 */ 163 {4, 850, 4, 6, 0xff, 2, 0}, 164 {4, 950, 5, 7, 0xff, 2, 0}, 165 {4, 1050, 5, 8, 0xff, 2, 0}, 166 {4, 1250, 5, 10, 0xff, 2, 0}, 167 {4, 1350, 5, 11, 0xff, 2, 0}, 168 {4, 1666, 5, 12, 0xff, 2, 0}, 169 {2, 850, 4, 6, 0xff, 2, 0}, 170 {2, 1050, 4, 7, 0xff, 2, 0}, 171 {2, 1666, 4, 8, 0xff, 2, 0}, 172 {1, 850, 4, 5, 0xff, 2, 0}, 173 {1, 950, 4, 7, 0xff, 2, 0}, 174 {1, 1666, 4, 8, 0xff, 2, 0}, 175 {} 176 }; 177 178 /* 179 * The two slots have slightly different timing. See comments above. 180 */ 181 static const struct board_specific_parameters *rdimms[] = { 182 rdimm0, 183 rdimm0, 184 }; 185 186 void fsl_ddr_board_options(memctl_options_t *popts, 187 dimm_params_t *pdimm, 188 unsigned int ctrl_num) 189 { 190 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; 191 ulong ddr_freq; 192 193 if (ctrl_num > 1) { 194 printf("Wrong parameter for controller number %d", ctrl_num); 195 return; 196 } 197 if (!pdimm->n_ranks) 198 return; 199 200 if (popts->registered_dimm_en) 201 pbsp = rdimms[ctrl_num]; 202 else 203 pbsp = udimms[ctrl_num]; 204 205 206 /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr 207 * freqency and n_banks specified in board_specific_parameters table. 208 */ 209 ddr_freq = get_ddr_freq(0) / 1000000; 210 while (pbsp->datarate_mhz_high) { 211 if (pbsp->n_ranks == pdimm->n_ranks) { 212 if (ddr_freq <= pbsp->datarate_mhz_high) { 213 popts->cpo_override = pbsp->cpo; 214 popts->write_data_delay = 215 pbsp->write_data_delay; 216 popts->clk_adjust = pbsp->clk_adjust; 217 popts->wrlvl_start = pbsp->wrlvl_start; 218 popts->twot_en = pbsp->force_2t; 219 goto found; 220 } 221 pbsp_highest = pbsp; 222 } 223 pbsp++; 224 } 225 226 if (pbsp_highest) { 227 printf("Error: board specific timing not found " 228 "for data rate %lu MT/s!\n" 229 "Trying to use the highest speed (%u) parameters\n", 230 ddr_freq, pbsp_highest->datarate_mhz_high); 231 popts->cpo_override = pbsp_highest->cpo; 232 popts->write_data_delay = pbsp_highest->write_data_delay; 233 popts->clk_adjust = pbsp_highest->clk_adjust; 234 popts->wrlvl_start = pbsp_highest->wrlvl_start; 235 popts->twot_en = pbsp_highest->force_2t; 236 } else { 237 panic("DIMM is not supported by this board"); 238 } 239 found: 240 /* 241 * Factors to consider for half-strength driver enable: 242 * - number of DIMMs installed 243 */ 244 popts->half_strength_driver_enable = 0; 245 /* 246 * Write leveling override 247 */ 248 popts->wrlvl_override = 1; 249 popts->wrlvl_sample = 0xf; 250 251 /* 252 * Rtt and Rtt_WR override 253 */ 254 popts->rtt_override = 0; 255 256 /* Enable ZQ calibration */ 257 popts->zq_en = 1; 258 259 /* DHC_EN =1, ODT = 60 Ohm */ 260 popts->ddr_cdr1 = DDR_CDR1_DHC_EN; 261 } 262 263 phys_size_t initdram(int board_type) 264 { 265 phys_size_t dram_size; 266 267 puts("Initializing...."); 268 269 if (fsl_use_spd()) { 270 puts("using SPD\n"); 271 dram_size = fsl_ddr_sdram(); 272 } else { 273 puts("using fixed parameters\n"); 274 dram_size = fixed_sdram(); 275 } 276 277 dram_size = setup_ddr_tlbs(dram_size / 0x100000); 278 dram_size *= 0x100000; 279 280 debug(" DDR: "); 281 return dram_size; 282 } 283