1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <command.h> 9 #include <i2c.h> 10 #include <asm/io.h> 11 #ifdef CONFIG_LS1043A 12 #include <asm/arch/immap_lsch2.h> 13 #else 14 #include <asm/immap_85xx.h> 15 #endif 16 #include "vid.h" 17 18 DECLARE_GLOBAL_DATA_PTR; 19 20 int __weak i2c_multiplexer_select_vid_channel(u8 channel) 21 { 22 return 0; 23 } 24 25 /* 26 * Compensate for a board specific voltage drop between regulator and SoC 27 * return a value in mV 28 */ 29 int __weak board_vdd_drop_compensation(void) 30 { 31 return 0; 32 } 33 34 /* 35 * Get the i2c address configuration for the IR regulator chip 36 * 37 * There are some variance in the RDB HW regarding the I2C address configuration 38 * for the IR regulator chip, which is likely a problem of external resistor 39 * accuracy. So we just check each address in a hopefully non-intrusive mode 40 * and use the first one that seems to work 41 * 42 * The IR chip can show up under the following addresses: 43 * 0x08 (Verified on T1040RDB-PA,T4240RDB-PB,X-T4240RDB-16GPA) 44 * 0x09 (Verified on T1040RDB-PA) 45 * 0x38 (Verified on T2080QDS, T2081QDS, T4240RDB) 46 */ 47 static int find_ir_chip_on_i2c(void) 48 { 49 int i2caddress; 50 int ret; 51 u8 byte; 52 int i; 53 const int ir_i2c_addr[] = {0x38, 0x08, 0x09}; 54 55 /* Check all the address */ 56 for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) { 57 i2caddress = ir_i2c_addr[i]; 58 ret = i2c_read(i2caddress, 59 IR36021_MFR_ID_OFFSET, 1, (void *)&byte, 60 sizeof(byte)); 61 if ((ret >= 0) && (byte == IR36021_MFR_ID)) 62 return i2caddress; 63 } 64 return -1; 65 } 66 67 /* Maximum loop count waiting for new voltage to take effect */ 68 #define MAX_LOOP_WAIT_NEW_VOL 100 69 /* Maximum loop count waiting for the voltage to be stable */ 70 #define MAX_LOOP_WAIT_VOL_STABLE 100 71 /* 72 * read_voltage from sensor on I2C bus 73 * We use average of 4 readings, waiting for WAIT_FOR_ADC before 74 * another reading 75 */ 76 #define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */ 77 78 /* If an INA220 chip is available, we can use it to read back the voltage 79 * as it may have a higher accuracy than the IR chip for the same purpose 80 */ 81 #ifdef CONFIG_VOL_MONITOR_INA220 82 #define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */ 83 #define ADC_MIN_ACCURACY 4 84 #else 85 #define WAIT_FOR_ADC 138 /* wait for 138 microseconds for ADC */ 86 #define ADC_MIN_ACCURACY 4 87 #endif 88 89 #ifdef CONFIG_VOL_MONITOR_INA220 90 static int read_voltage_from_INA220(int i2caddress) 91 { 92 int i, ret, voltage_read = 0; 93 u16 vol_mon; 94 u8 buf[2]; 95 96 for (i = 0; i < NUM_READINGS; i++) { 97 ret = i2c_read(I2C_VOL_MONITOR_ADDR, 98 I2C_VOL_MONITOR_BUS_V_OFFSET, 1, 99 (void *)&buf, 2); 100 if (ret) { 101 printf("VID: failed to read core voltage\n"); 102 return ret; 103 } 104 vol_mon = (buf[0] << 8) | buf[1]; 105 if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) { 106 printf("VID: Core voltage sensor error\n"); 107 return -1; 108 } 109 debug("VID: bus voltage reads 0x%04x\n", vol_mon); 110 /* LSB = 4mv */ 111 voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4; 112 udelay(WAIT_FOR_ADC); 113 } 114 /* calculate the average */ 115 voltage_read /= NUM_READINGS; 116 117 return voltage_read; 118 } 119 #endif 120 121 /* read voltage from IR */ 122 #ifdef CONFIG_VOL_MONITOR_IR36021_READ 123 static int read_voltage_from_IR(int i2caddress) 124 { 125 int i, ret, voltage_read = 0; 126 u16 vol_mon; 127 u8 buf; 128 129 for (i = 0; i < NUM_READINGS; i++) { 130 ret = i2c_read(i2caddress, 131 IR36021_LOOP1_VOUT_OFFSET, 132 1, (void *)&buf, 1); 133 if (ret) { 134 printf("VID: failed to read vcpu\n"); 135 return ret; 136 } 137 vol_mon = buf; 138 if (!vol_mon) { 139 printf("VID: Core voltage sensor error\n"); 140 return -1; 141 } 142 debug("VID: bus voltage reads 0x%02x\n", vol_mon); 143 /* Resolution is 1/128V. We scale up here to get 1/128mV 144 * and divide at the end 145 */ 146 voltage_read += vol_mon * 1000; 147 udelay(WAIT_FOR_ADC); 148 } 149 /* Scale down to the real mV as IR resolution is 1/128V, rounding up */ 150 voltage_read = DIV_ROUND_UP(voltage_read, 128); 151 152 /* calculate the average */ 153 voltage_read /= NUM_READINGS; 154 155 /* Compensate for a board specific voltage drop between regulator and 156 * SoC before converting into an IR VID value 157 */ 158 voltage_read -= board_vdd_drop_compensation(); 159 160 return voltage_read; 161 } 162 #endif 163 164 static int read_voltage(int i2caddress) 165 { 166 int voltage_read; 167 #ifdef CONFIG_VOL_MONITOR_INA220 168 voltage_read = read_voltage_from_INA220(i2caddress); 169 #elif defined CONFIG_VOL_MONITOR_IR36021_READ 170 voltage_read = read_voltage_from_IR(i2caddress); 171 #else 172 return -1; 173 #endif 174 return voltage_read; 175 } 176 177 /* 178 * We need to calculate how long before the voltage stops to drop 179 * or increase. It returns with the loop count. Each loop takes 180 * several readings (WAIT_FOR_ADC) 181 */ 182 static int wait_for_new_voltage(int vdd, int i2caddress) 183 { 184 int timeout, vdd_current; 185 186 vdd_current = read_voltage(i2caddress); 187 /* wait until voltage starts to reach the target. Voltage slew 188 * rates by typical regulators will always lead to stable readings 189 * within each fairly long ADC interval in comparison to the 190 * intended voltage delta change until the target voltage is 191 * reached. The fairly small voltage delta change to any target 192 * VID voltage also means that this function will always complete 193 * within few iterations. If the timeout was ever reached, it would 194 * point to a serious failure in the regulator system. 195 */ 196 for (timeout = 0; 197 abs(vdd - vdd_current) > (IR_VDD_STEP_UP + IR_VDD_STEP_DOWN) && 198 timeout < MAX_LOOP_WAIT_NEW_VOL; timeout++) { 199 vdd_current = read_voltage(i2caddress); 200 } 201 if (timeout >= MAX_LOOP_WAIT_NEW_VOL) { 202 printf("VID: Voltage adjustment timeout\n"); 203 return -1; 204 } 205 return timeout; 206 } 207 208 /* 209 * this function keeps reading the voltage until it is stable or until the 210 * timeout expires 211 */ 212 static int wait_for_voltage_stable(int i2caddress) 213 { 214 int timeout, vdd_current, vdd; 215 216 vdd = read_voltage(i2caddress); 217 udelay(NUM_READINGS * WAIT_FOR_ADC); 218 219 /* wait until voltage is stable */ 220 vdd_current = read_voltage(i2caddress); 221 /* The maximum timeout is 222 * MAX_LOOP_WAIT_VOL_STABLE * NUM_READINGS * WAIT_FOR_ADC 223 */ 224 for (timeout = MAX_LOOP_WAIT_VOL_STABLE; 225 abs(vdd - vdd_current) > ADC_MIN_ACCURACY && 226 timeout > 0; timeout--) { 227 vdd = vdd_current; 228 udelay(NUM_READINGS * WAIT_FOR_ADC); 229 vdd_current = read_voltage(i2caddress); 230 } 231 if (timeout == 0) 232 return -1; 233 return vdd_current; 234 } 235 236 #ifdef CONFIG_VOL_MONITOR_IR36021_SET 237 /* Set the voltage to the IR chip */ 238 static int set_voltage_to_IR(int i2caddress, int vdd) 239 { 240 int wait, vdd_last; 241 int ret; 242 u8 vid; 243 244 /* Compensate for a board specific voltage drop between regulator and 245 * SoC before converting into an IR VID value 246 */ 247 vdd += board_vdd_drop_compensation(); 248 #ifdef CONFIG_LS1043A 249 vid = DIV_ROUND_UP(vdd - 265, 5); 250 #else 251 vid = DIV_ROUND_UP(vdd - 245, 5); 252 #endif 253 254 ret = i2c_write(i2caddress, IR36021_LOOP1_MANUAL_ID_OFFSET, 255 1, (void *)&vid, sizeof(vid)); 256 if (ret) { 257 printf("VID: failed to write VID\n"); 258 return -1; 259 } 260 wait = wait_for_new_voltage(vdd, i2caddress); 261 if (wait < 0) 262 return -1; 263 debug("VID: Waited %d us\n", wait * NUM_READINGS * WAIT_FOR_ADC); 264 265 vdd_last = wait_for_voltage_stable(i2caddress); 266 if (vdd_last < 0) 267 return -1; 268 debug("VID: Current voltage is %d mV\n", vdd_last); 269 return vdd_last; 270 } 271 #endif 272 273 static int set_voltage(int i2caddress, int vdd) 274 { 275 int vdd_last = -1; 276 277 #ifdef CONFIG_VOL_MONITOR_IR36021_SET 278 vdd_last = set_voltage_to_IR(i2caddress, vdd); 279 #else 280 #error Specific voltage monitor must be defined 281 #endif 282 return vdd_last; 283 } 284 285 int adjust_vdd(ulong vdd_override) 286 { 287 int re_enable = disable_interrupts(); 288 #ifdef CONFIG_LS1043A 289 struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); 290 #else 291 ccsr_gur_t __iomem *gur = 292 (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); 293 #endif 294 u32 fusesr; 295 u8 vid, buf; 296 int vdd_target, vdd_current, vdd_last; 297 int ret, i2caddress; 298 unsigned long vdd_string_override; 299 char *vdd_string; 300 static const uint16_t vdd[32] = { 301 0, /* unused */ 302 9875, /* 0.9875V */ 303 9750, 304 9625, 305 9500, 306 9375, 307 9250, 308 9125, 309 9000, 310 8875, 311 8750, 312 8625, 313 8500, 314 8375, 315 8250, 316 8125, 317 10000, /* 1.0000V */ 318 10125, 319 10250, 320 10375, 321 10500, 322 10625, 323 10750, 324 10875, 325 11000, 326 0, /* reserved */ 327 }; 328 struct vdd_drive { 329 u8 vid; 330 unsigned voltage; 331 }; 332 333 ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR); 334 if (ret) { 335 debug("VID: I2C failed to switch channel\n"); 336 ret = -1; 337 goto exit; 338 } 339 ret = find_ir_chip_on_i2c(); 340 if (ret < 0) { 341 printf("VID: Could not find voltage regulator on I2C.\n"); 342 ret = -1; 343 goto exit; 344 } else { 345 i2caddress = ret; 346 debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress); 347 } 348 349 /* check IR chip work on Intel mode*/ 350 ret = i2c_read(i2caddress, 351 IR36021_INTEL_MODE_OOFSET, 352 1, (void *)&buf, 1); 353 if (ret) { 354 printf("VID: failed to read IR chip mode.\n"); 355 ret = -1; 356 goto exit; 357 } 358 if ((buf & IR36021_MODE_MASK) != IR36021_INTEL_MODE) { 359 printf("VID: IR Chip is not used in Intel mode.\n"); 360 ret = -1; 361 goto exit; 362 } 363 364 /* get the voltage ID from fuse status register */ 365 fusesr = in_be32(&gur->dcfg_fusesr); 366 /* 367 * VID is used according to the table below 368 * --------------------------------------- 369 * | DA_V | 370 * |-------------------------------------| 371 * | 5b00000 | 5b00001-5b11110 | 5b11111 | 372 * ---------------+---------+-----------------+---------| 373 * | D | 5b00000 | NO VID | VID = DA_V | NO VID | 374 * | A |----------+---------+-----------------+---------| 375 * | _ | 5b00001 |VID = | VID = |VID = | 376 * | V | ~ | DA_V_ALT| DA_V_ALT | DA_A_VLT| 377 * | _ | 5b11110 | | | | 378 * | A |----------+---------+-----------------+---------| 379 * | L | 5b11111 | No VID | VID = DA_V | NO VID | 380 * | T | | | | | 381 * ------------------------------------------------------ 382 */ 383 #ifdef CONFIG_LS1043A 384 vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_ALTVID_SHIFT) & 385 FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK; 386 if ((vid == 0) || (vid == FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK)) { 387 vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_VID_SHIFT) & 388 FSL_CHASSIS2_DCFG_FUSESR_VID_MASK; 389 } 390 #else 391 vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) & 392 FSL_CORENET_DCFG_FUSESR_ALTVID_MASK; 393 if ((vid == 0) || (vid == FSL_CORENET_DCFG_FUSESR_ALTVID_MASK)) { 394 vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) & 395 FSL_CORENET_DCFG_FUSESR_VID_MASK; 396 } 397 #endif 398 vdd_target = vdd[vid]; 399 400 /* check override variable for overriding VDD */ 401 vdd_string = getenv(CONFIG_VID_FLS_ENV); 402 if (vdd_override == 0 && vdd_string && 403 !strict_strtoul(vdd_string, 10, &vdd_string_override)) 404 vdd_override = vdd_string_override; 405 if (vdd_override >= VDD_MV_MIN && vdd_override <= VDD_MV_MAX) { 406 vdd_target = vdd_override * 10; /* convert to 1/10 mV */ 407 debug("VDD override is %lu\n", vdd_override); 408 } else if (vdd_override != 0) { 409 printf("Invalid value.\n"); 410 } 411 if (vdd_target == 0) { 412 debug("VID: VID not used\n"); 413 ret = 0; 414 goto exit; 415 } else { 416 /* divide and round up by 10 to get a value in mV */ 417 vdd_target = DIV_ROUND_UP(vdd_target, 10); 418 debug("VID: vid = %d mV\n", vdd_target); 419 } 420 421 /* 422 * Read voltage monitor to check real voltage. 423 */ 424 vdd_last = read_voltage(i2caddress); 425 if (vdd_last < 0) { 426 printf("VID: Couldn't read sensor abort VID adjustment\n"); 427 ret = -1; 428 goto exit; 429 } 430 vdd_current = vdd_last; 431 debug("VID: Core voltage is currently at %d mV\n", vdd_last); 432 /* 433 * Adjust voltage to at or one step above target. 434 * As measurements are less precise than setting the values 435 * we may run through dummy steps that cancel each other 436 * when stepping up and then down. 437 */ 438 while (vdd_last > 0 && 439 vdd_last < vdd_target) { 440 vdd_current += IR_VDD_STEP_UP; 441 vdd_last = set_voltage(i2caddress, vdd_current); 442 } 443 while (vdd_last > 0 && 444 vdd_last > vdd_target + (IR_VDD_STEP_DOWN - 1)) { 445 vdd_current -= IR_VDD_STEP_DOWN; 446 vdd_last = set_voltage(i2caddress, vdd_current); 447 } 448 449 if (vdd_last > 0) 450 printf("VID: Core voltage after adjustment is at %d mV\n", 451 vdd_last); 452 else 453 ret = -1; 454 exit: 455 if (re_enable) 456 enable_interrupts(); 457 return ret; 458 } 459 460 static int print_vdd(void) 461 { 462 int vdd_last, ret, i2caddress; 463 464 ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR); 465 if (ret) { 466 debug("VID : I2c failed to switch channel\n"); 467 return -1; 468 } 469 ret = find_ir_chip_on_i2c(); 470 if (ret < 0) { 471 printf("VID: Could not find voltage regulator on I2C.\n"); 472 return -1; 473 } else { 474 i2caddress = ret; 475 debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress); 476 } 477 478 /* 479 * Read voltage monitor to check real voltage. 480 */ 481 vdd_last = read_voltage(i2caddress); 482 if (vdd_last < 0) { 483 printf("VID: Couldn't read sensor abort VID adjustment\n"); 484 return -1; 485 } 486 printf("VID: Core voltage is at %d mV\n", vdd_last); 487 488 return 0; 489 } 490 491 static int do_vdd_override(cmd_tbl_t *cmdtp, 492 int flag, int argc, 493 char * const argv[]) 494 { 495 ulong override; 496 497 if (argc < 2) 498 return CMD_RET_USAGE; 499 500 if (!strict_strtoul(argv[1], 10, &override)) 501 adjust_vdd(override); /* the value is checked by callee */ 502 else 503 return CMD_RET_USAGE; 504 return 0; 505 } 506 507 static int do_vdd_read(cmd_tbl_t *cmdtp, 508 int flag, int argc, 509 char * const argv[]) 510 { 511 if (argc < 1) 512 return CMD_RET_USAGE; 513 print_vdd(); 514 515 return 0; 516 } 517 518 U_BOOT_CMD( 519 vdd_override, 2, 0, do_vdd_override, 520 "override VDD", 521 " - override with the voltage specified in mV, eg. 1050" 522 ); 523 524 U_BOOT_CMD( 525 vdd_read, 1, 0, do_vdd_read, 526 "read VDD", 527 " - Read the voltage specified in mV" 528 ) 529