1# 2# Copyright (C) 2011 3# Stefan Herbrechtsmeier <stefan@code.herbrechtsmeier.net> 4# 5# Based on Kirkwood support: 6# (C) Copyright 2009 7# Marvell Semiconductor <www.marvell.com> 8# Written-by: Prafulla Wadaskar <prafulla@marvell.com> 9# 10# SPDX-License-Identifier: GPL-2.0+ 11# 12# Refer doc/README.kwbimage for more details about how-to configure 13# and create kirkwood boot image 14# 15 16# Boot Media configurations 17BOOT_FROM nand 18NAND_ECC_MODE default 19NAND_PAGE_SIZE 0x0800 20 21# SOC registers configuration using bootrom header extension 22# Maximum KWBIMAGE_MAX_CONFIG configurations allowed 23 24# Configure RGMII-0 interface pad voltage to 1.8V 25DATA 0xFFD100e0 0x1b1b1b9b 26 27#Dram initalization for SINGLE x16 CL=5 @ 400MHz 28DATA 0xFFD01400 0x43000c30 # DDR Configuration register 29# bit13-0: 0xc30, 3120 DDR2 clks refresh rate 30# bit23-14: 0 required 31# bit24: 1, enable exit self refresh mode on DDR access 32# bit25: 1 required 33# bit29-26: 0 required 34# bit31-30: 0b01 required 35 36DATA 0xFFD01404 0x39543000 # DDR Controller Control Low 37# bit3-0: 0 required 38# bit4: 0, addr/cmd in smame cycle 39# bit5: 0, clk is driven during self refresh, we don't care for APX 40# bit6: 0, use recommended falling edge of clk for addr/cmd 41# bit11-7: 0 required 42# bit12: 1 required 43# bit13: 1 required 44# bit14: 0, input buffer always powered up 45# bit17-15: 0 required 46# bit18: 1, cpu lock transaction enabled 47# bit19: 0 required 48# bit23-20: 5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 49# bit27-24: 9, CL+4, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM 50# bit30-28: 3 required 51# bit31: 0, no additional STARTBURST delay 52 53DATA 0xFFD01408 0x22125451 # DDR Timing (Low) 54# bit3-0: 1, 18 cycle tRAS (tRAS[3-0]) 55# bit7-4: 5, 6 cycle tRCD 56# bit11-8: 4, 5 cyle tRP 57# bit15-12: 5, 6 cyle tWR 58# bit19-16: 2, 3 cyle tWTR 59# bit20: 1, 18 cycle tRAS (tRAS[4]) 60# bit23-21: 0 required 61# bit27-24: 2, 3 cycle tRRD 62# bit31-28: 2, 3 cyle tRTP 63 64DATA 0xFFD0140C 0x00000833 # DDR Timing (High) 65# bit6-0: 0x33, 33 cycle tRFC 66# bit8-7: 0, 1 cycle tR2R 67# bit10-9: 0, 1 cyle tR2W 68# bit12-11: 1, 2 cylce tW2W 69# bit31-13: 0 required 70 71DATA 0xFFD01410 0x0000000c # DDR Address Control 72# bit1-0: 0, Cs0width=x8 73# bit3-2: 3, Cs0size=1Gb 74# bit5-4: 0, Cs1width=nonexistent 75# bit7-6: 0, Cs1size=nonexistent 76# bit9-8: 0, Cs2width=nonexistent 77# bit11-10: 0, Cs2size=nonexistent 78# bit13-12: 0, Cs3width=nonexistent 79# bit15-14: 0, Cs3size=nonexistent 80# bit16: 0, Cs0AddrSel 81# bit17: 0, Cs1AddrSel 82# bit18: 0, Cs2AddrSel 83# bit19: 0, Cs3AddrSel 84# bit31-20: 0 required 85 86DATA 0xFFD01414 0x00000000 # DDR Open Pages Control 87# bit0: 0, OPEn=OpenPage enabled 88# bit31-1: 0 required 89 90DATA 0xFFD01418 0x00000000 # DDR Operation 91# bit3-0: 0, Cmd=Normal SDRAM Mode 92# bit31-4: 0 required 93 94DATA 0xFFD0141C 0x00000C52 # DDR Mode 95# bit2-0: 2, Burst Length (2 required) 96# bit3: 0, Burst Type (0 required) 97# bit6-4: 5, CAS Latency (CL) 5 98# bit7: 0, (Test Mode) Normal operation 99# bit8: 0, (Reset DLL) Normal operation 100# bit11-9: 0, Write recovery for auto-precharge (3 required ??) 101# bit12: 0, Fast Active power down exit time (0 required) 102# bit31-13: 0 required 103 104DATA 0xFFD01420 0x00000040 # DDR Extended Mode 105# bit0: 0, DRAM DLL enabled 106# bit1: 0, DRAM drive strength normal 107# bit2: 0, ODT control Rtt[0] (Rtt=2, 150 ohm termination) 108# bit5-3: 0 required 109# bit6: 1, ODT control Rtt[1] (Rtt=2, 150 ohm termination) 110# bit9-7: 0 required 111# bit10: 0, differential DQS enabled 112# bit11: 0 required 113# bit12: 0, DRAM output buffer enabled 114# bit31-13: 0 required 115 116DATA 0xFFD01424 0x0000F17F # DDR Controller Control High 117# bit2-0: 0x7 required 118# bit3: 1, MBUS Burst Chop disabled 119# bit6-4: 0x7 required 120# bit7: 0 required 121# bit8: 1, add writepath sample stage, must be 1 for DDR freq >= 300MHz 122# bit9: 0, no half clock cycle addition to dataout 123# bit10: 0, 1/4 clock cycle skew enabled for addr/ctl signals 124# bit11: 0, 1/4 clock cycle skew disabled for write mesh 125# bit15-12: 0xf required 126# bit31-16: 0 required 127 128DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing 129# bit3-0: 0 required 130# bit7-4: 2, 2 cycles from read command to assertion of M_ODT signal 131# bit11-8: 5, 5 cycles from read command to de-assertion of M_ODT signal 132# bit15-12: 5, 5 cycles from read command to assertion of internal ODT signal 133# bit19-16: 8, 8 cycles from read command to de-assertion of internal ODT signal 134# bit31-20: 0 required 135 136DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing 137# bit3-0: 2, 2 cycles from write comand to assertion of M_ODT signal 138# bit7-4: 5, 5 cycles from write command to de-assertion of M_ODT signal 139# bit15-12: 5, 5 cycles from write command to assertion of internal ODT signal 140# bit19-16: 8, 8 cycles from write command to de-assertion of internal ODT signal 141# bit31-16: 0 required 142 143DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 144DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size 145# bit0: 1, Window enabled 146# bit1: 0, Write Protect disabled 147# bit3-2: 0x0, CS0 hit selected 148# bit23-4: 0xfffff required 149# bit31-24: 0x0f, Size (i.e. 256MB) 150 151DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb 152DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 153# bit0: 1, Window enabled 154# bit1: 0, Write Protect disabled 155# bit3-2: 1, CS1 hit selected 156# bit23-4: 0xfffff required 157# bit31-24: 0x0f, Size (i.e. 256MB) 158 159DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled 160DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled 161 162DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) 163# bit3-0: 0b0000, (read) M_ODT[0] is not asserted during read from DRAM 164# bit7-4: 0b0000, (read) M_ODT[1] is not asserted during read from DRAM 165# bit15-8: 0 required 166# bit19-16: 0b0011, (write) M_ODT[0] is asserted during write to DRAM CS0 and CS1 167# bit23-20: 0b0000, (write) M_ODT[1] is not asserted during write to DRAM 168# bit31-24: 0 required 169 170DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) 171# bit1-0: 0, M_ODT[0] assertion is controlled by ODT Control Low register 172# bit3-2: 0, M_ODT[1] assertion is controlled by ODT Control Low register 173# bit31-4 0 required 174 175DATA 0xFFD0149C 0x0000E803 # CPU ODT Control 176# bit3-0: 0b0011, internal ODT is asserted during read from DRAM bank 0-1 177# bit7-4: 0b0000, internal ODT is not asserted during write to DRAM bank 0-4 178# bit9-8: 0, Internal ODT assertion is controlled by fiels 179# bit11-10: 2, M_DQ, M_DM, and M_DQS I/O buffer ODT 75 ohm 180# bit13-12: 2, M_STARTBURST_IN I/O buffer ODT 75 ohm 181# bit14: 1, M_STARTBURST_IN ODT enabled 182# bit15: 1, DDR IO ODT Unit: Drive ODT calibration values 183# bit20-16: 0, Pad N channel driving strength for ODT 184# bit25-21: 0, Pad P channel driving strength for ODT 185# bit31-26: 0 required 186 187DATA 0xFFD01480 0x00000001 # DDR Initialization Control 188# bit0: 1, enable DDR init upon this register write 189# bit31-1: 0, required 190 191# End of Header extension 192DATA 0x0 0x0 193