1 /*
2  * (C) Copyright 2012
3  * Corscience GmbH & Co. KG, <www.corscience.de>
4  * Thomas Weber <weber@corscience.de>
5  * Sunil Kumar <sunilsaini05@gmail.com>
6  * Shashi Ranjan <shashiranjanmca05@gmail.com>
7  *
8  * Derived from Devkit8000 code by
9  * Frederik Kriewitz <frederik@kriewitz.eu>
10  *
11  * SPDX-License-Identifier:	GPL-2.0+
12  */
13 #include <common.h>
14 #include <twl4030.h>
15 #include <asm/io.h>
16 #include <asm/gpio.h>
17 #include <asm/arch/mmc_host_def.h>
18 #include <asm/arch/mux.h>
19 #include <asm/arch/sys_proto.h>
20 #include <asm/arch/mem.h>
21 #include "tricorder.h"
22 #include "tricorder-eeprom.h"
23 
24 DECLARE_GLOBAL_DATA_PTR;
25 
26 /*
27  * Routine: board_init
28  * Description: Early hardware init.
29  */
30 int board_init(void)
31 {
32 	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
33 	/* boot param addr */
34 	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
35 
36 	return 0;
37 }
38 
39 /**
40  * get_eeprom - read the eeprom
41  *
42  * @eeprom - pointer to a eeprom struct to fill
43  *
44  * This function will panic() on wrong EEPROM content
45  */
46 static void get_eeprom(struct tricorder_eeprom *eeprom)
47 {
48 	int ret;
49 
50 	if (!eeprom)
51 		panic("No eeprom given!\n");
52 
53 	ret = gpio_request(7, "BMS");
54 	if (ret)
55 		panic("gpio: requesting BMS pin failed\n");
56 
57 	ret = gpio_direction_input(7);
58 	if (ret)
59 		panic("gpio: set BMS as input failed\n");
60 
61 	ret = gpio_get_value(7);
62 	if (ret < 0)
63 		panic("gpio: get BMS pin state failed\n");
64 
65 	gpio_free(7);
66 
67 	if (ret == 0) {
68 		/* BMS is _not_ set, do the EEPROM check */
69 		ret = tricorder_get_eeprom(0x51, eeprom);
70 		if (!ret) {
71 			if (strncmp(eeprom->board_name, "CS10411", 7) != 0)
72 				panic("Wrong board name '%.*s'\n",
73 				      sizeof(eeprom->board_name),
74 						eeprom->board_name);
75 			if (eeprom->board_version[0] < 'D')
76 				panic("Wrong board version '%.*s'\n",
77 				      sizeof(eeprom->board_version),
78 						eeprom->board_version);
79 		} else {
80 			panic("Could not get board revision\n");
81 		}
82 	} else {
83 		memset(eeprom, 0, TRICORDER_EEPROM_SIZE);
84 	}
85 }
86 
87 /**
88  * print_hwversion - print out a HW version string
89  *
90  * @eeprom - pointer to the eeprom
91  */
92 static void print_hwversion(struct tricorder_eeprom *eeprom)
93 {
94 	size_t len;
95 	if (!eeprom)
96 		panic("No eeprom given!");
97 
98 	printf("Board %.*s:%.*s serial %.*s",
99 	       sizeof(eeprom->board_name), eeprom->board_name,
100 	       sizeof(eeprom->board_version), eeprom->board_version,
101 	       sizeof(eeprom->board_serial), eeprom->board_serial);
102 
103 	len = strnlen(eeprom->interface_version,
104 		      sizeof(eeprom->interface_version));
105 	if (len > 0)
106 		printf(" HW interface version %.*s",
107 		       sizeof(eeprom->interface_version),
108 		       eeprom->interface_version);
109 	puts("\n");
110 }
111 
112 /*
113  * Routine: misc_init_r
114  * Description: Configure board specific parts
115  */
116 int misc_init_r(void)
117 {
118 	struct tricorder_eeprom eeprom;
119 	get_eeprom(&eeprom);
120 	print_hwversion(&eeprom);
121 
122 	twl4030_power_init();
123 	status_led_set(0, CONFIG_LED_STATUS_ON);
124 	status_led_set(1, CONFIG_LED_STATUS_ON);
125 	status_led_set(2, CONFIG_LED_STATUS_ON);
126 
127 	omap_die_id_display();
128 
129 	return 0;
130 }
131 
132 /*
133  * Routine: set_muxconf_regs
134  * Description: Setting up the configuration Mux registers specific to the
135  *		hardware. Many pins need to be moved from protect to primary
136  *		mode.
137  */
138 void set_muxconf_regs(void)
139 {
140 	MUX_TRICORDER();
141 }
142 
143 #if defined(CONFIG_GENERIC_MMC) && !(defined(CONFIG_SPL_BUILD))
144 int board_mmc_init(bd_t *bis)
145 {
146 	return omap_mmc_init(0, 0, 0, -1, -1);
147 }
148 #endif
149 
150 #if defined(CONFIG_GENERIC_MMC)
151 void board_mmc_power_init(void)
152 {
153 	twl4030_power_mmc_init(0);
154 }
155 #endif
156 
157 /*
158  * Routine: get_board_mem_timings
159  * Description: If we use SPL then there is no x-loader nor config header
160  * so we have to setup the DDR timings ourself on the first bank.  This
161  * provides the timing values back to the function that configures
162  * the memory.  We have either one or two banks of 128MB DDR.
163  */
164 void get_board_mem_timings(struct board_sdrc_timings *timings)
165 {
166 	struct tricorder_eeprom eeprom;
167 	get_eeprom(&eeprom);
168 
169 	/* General SDRC config */
170 	if (eeprom.board_version[0] > 'D') {
171 		/* use optimized timings for our SDRAM device */
172 		timings->mcfg = MCFG((256 << 20), 14);
173 #define MT46H64M32_TDAL  6	/* Twr/Tck + Trp/tck		*/
174 				/* 15/6 + 18/6 = 5.5 -> 6	*/
175 #define MT46H64M32_TDPL  3	/* 15/6 = 2.5 -> 3 (Twr)	*/
176 #define MT46H64M32_TRRD  2	/* 12/6 = 2			*/
177 #define MT46H64M32_TRCD  3	/* 18/6 = 3			*/
178 #define MT46H64M32_TRP   3	/* 18/6 = 3			*/
179 #define MT46H64M32_TRAS  7	/* 42/6 = 7			*/
180 #define MT46H64M32_TRC  10	/* 60/6 = 10			*/
181 #define MT46H64M32_TRFC 12	/* 72/6 = 12			*/
182 		timings->ctrla = ACTIM_CTRLA(MT46H64M32_TRFC, MT46H64M32_TRC,
183 					     MT46H64M32_TRAS, MT46H64M32_TRP,
184 					     MT46H64M32_TRCD, MT46H64M32_TRRD,
185 					     MT46H64M32_TDPL,
186 					     MT46H64M32_TDAL);
187 
188 #define MT46H64M32_TWTR 1
189 #define MT46H64M32_TCKE 1
190 #define MT46H64M32_XSR 19	/* 112.5/6 = 18.75 => ~19	*/
191 #define MT46H64M32_TXP 1
192 		timings->ctrlb = ACTIM_CTRLB(MT46H64M32_TWTR, MT46H64M32_TCKE,
193 					     MT46H64M32_TXP, MT46H64M32_XSR);
194 
195 		timings->mr = MICRON_V_MR_165;
196 		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
197 	} else {
198 		/* use conservative beagleboard timings as default */
199 		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
200 		timings->ctrla = MICRON_V_ACTIMA_165;
201 		timings->ctrlb = MICRON_V_ACTIMB_165;
202 		timings->mr = MICRON_V_MR_165;
203 		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
204 	}
205 }
206