1 /* 2 * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. 3 * Based on mx6qsabrelite.c file 4 * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com> 5 * Leo Sartre, <lsartre@adeneo-embedded.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #include <common.h> 11 #include <asm/io.h> 12 #include <asm/arch/clock.h> 13 #include <asm/arch/imx-regs.h> 14 #include <asm/arch/iomux.h> 15 #include <asm/arch/mx6-pins.h> 16 #include <asm/gpio.h> 17 #include <asm/imx-common/iomux-v3.h> 18 #include <asm/imx-common/sata.h> 19 #include <asm/imx-common/boot_mode.h> 20 #include <asm/imx-common/mxc_i2c.h> 21 #include <asm/arch/sys_proto.h> 22 #include <asm/arch/mxc_hdmi.h> 23 #include <asm/arch/crm_regs.h> 24 #include <mmc.h> 25 #include <fsl_esdhc.h> 26 #include <i2c.h> 27 #include <power/pmic.h> 28 #include <power/pfuze100_pmic.h> 29 #include <linux/fb.h> 30 #include <ipu_pixfmt.h> 31 #include <malloc.h> 32 #include <miiphy.h> 33 #include <netdev.h> 34 #include <micrel.h> 35 #include <spi_flash.h> 36 #include <spi.h> 37 38 DECLARE_GLOBAL_DATA_PTR; 39 40 #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |\ 41 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 42 43 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\ 44 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 45 46 #define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 47 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 48 PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 49 PAD_CTL_ODE | PAD_CTL_SRE_FAST) 50 51 #define SPI_PAD_CTRL (PAD_CTL_HYS | \ 52 PAD_CTL_SPEED_MED | \ 53 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 54 55 #define MX6Q_QMX6_PFUZE_MUX IMX_GPIO_NR(6, 9) 56 57 58 #define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 59 PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 60 PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 61 62 int dram_init(void) 63 { 64 gd->ram_size = imx_ddr_size(); 65 66 return 0; 67 } 68 69 static iomux_v3_cfg_t const uart2_pads[] = { 70 IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), 71 IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), 72 }; 73 74 static iomux_v3_cfg_t const usdhc2_pads[] = { 75 IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 76 IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 77 IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 78 IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 79 IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 80 IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 81 IOMUX_PADS(PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 82 }; 83 84 static iomux_v3_cfg_t const usdhc3_pads[] = { 85 IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 86 IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 87 IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 88 IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 89 IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 90 IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 91 IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 92 IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 93 IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 94 IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 95 IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 96 }; 97 98 static iomux_v3_cfg_t const usdhc4_pads[] = { 99 IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 100 IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 101 IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 102 IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 103 IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 104 IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 105 IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 106 IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 107 IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 108 IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 109 IOMUX_PADS(PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)), 110 }; 111 112 static iomux_v3_cfg_t const usb_otg_pads[] = { 113 IOMUX_PADS(PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)), 114 IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)), 115 }; 116 117 static iomux_v3_cfg_t enet_pads_ksz9031[] = { 118 IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), 119 IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 120 IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 121 IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 122 IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 123 IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 124 IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 125 IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), 126 IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)), 127 IOMUX_PADS(PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)), 128 IOMUX_PADS(PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)), 129 IOMUX_PADS(PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL)), 130 IOMUX_PADS(PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)), 131 IOMUX_PADS(PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)), 132 IOMUX_PADS(PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL)), 133 }; 134 135 static iomux_v3_cfg_t enet_pads_final_ksz9031[] = { 136 IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 137 IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 138 IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 139 IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 140 IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 141 IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), 142 }; 143 144 static iomux_v3_cfg_t enet_pads_ar8035[] = { 145 IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), 146 IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 147 IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 148 IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 149 IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 150 IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 151 IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 152 IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), 153 IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)), 154 IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 155 IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 156 IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 157 IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 158 IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 159 IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), 160 }; 161 162 static iomux_v3_cfg_t const ecspi1_pads[] = { 163 IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)), 164 IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)), 165 IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)), 166 IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)), 167 }; 168 169 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) 170 struct i2c_pads_info mx6q_i2c_pad_info1 = { 171 .scl = { 172 .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC, 173 .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC, 174 .gp = IMX_GPIO_NR(4, 12) 175 }, 176 .sda = { 177 .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC, 178 .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC, 179 .gp = IMX_GPIO_NR(4, 13) 180 } 181 }; 182 183 struct i2c_pads_info mx6dl_i2c_pad_info1 = { 184 .scl = { 185 .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | PC, 186 .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | PC, 187 .gp = IMX_GPIO_NR(4, 12) 188 }, 189 .sda = { 190 .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC, 191 .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC, 192 .gp = IMX_GPIO_NR(4, 13) 193 } 194 }; 195 196 #define I2C_PMIC 1 /* I2C2 port is used to connect to the PMIC */ 197 198 struct interface_level { 199 char *name; 200 uchar value; 201 }; 202 203 static struct interface_level mipi_levels[] = { 204 {"0V0", 0x00}, 205 {"2V5", 0x17}, 206 }; 207 208 /* setup board specific PMIC */ 209 int power_init_board(void) 210 { 211 struct pmic *p; 212 u32 id1, id2, i; 213 int ret; 214 char const *lv_mipi; 215 216 /* configure I2C multiplexer */ 217 gpio_direction_output(MX6Q_QMX6_PFUZE_MUX, 1); 218 219 power_pfuze100_init(I2C_PMIC); 220 p = pmic_get("PFUZE100"); 221 if (!p) 222 return -EINVAL; 223 224 ret = pmic_probe(p); 225 if (ret) 226 return ret; 227 228 pmic_reg_read(p, PFUZE100_DEVICEID, &id1); 229 pmic_reg_read(p, PFUZE100_REVID, &id2); 230 printf("PFUZE100 Rev. [%02x/%02x] detected\n", id1, id2); 231 232 if (id2 >= 0x20) 233 return 0; 234 235 /* set level of MIPI if specified */ 236 lv_mipi = getenv("lv_mipi"); 237 if (lv_mipi) 238 return 0; 239 240 for (i = 0; i < ARRAY_SIZE(mipi_levels); i++) { 241 if (!strcmp(mipi_levels[i].name, lv_mipi)) { 242 printf("set MIPI level %s\n", mipi_levels[i].name); 243 ret = pmic_reg_write(p, PFUZE100_VGEN4VOL, 244 mipi_levels[i].value); 245 if (ret) 246 return ret; 247 } 248 } 249 250 return 0; 251 } 252 253 int board_eth_init(bd_t *bis) 254 { 255 struct phy_device *phydev; 256 struct mii_dev *bus; 257 unsigned short id1, id2; 258 int ret; 259 260 /* check whether KSZ9031 or AR8035 has to be configured */ 261 SETUP_IOMUX_PADS(enet_pads_ar8035); 262 263 /* phy reset */ 264 gpio_direction_output(IMX_GPIO_NR(3, 23), 0); 265 udelay(2000); 266 gpio_set_value(IMX_GPIO_NR(3, 23), 1); 267 udelay(500); 268 269 bus = fec_get_miibus(IMX_FEC_BASE, -1); 270 if (!bus) 271 return -EINVAL; 272 phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII); 273 if (!phydev) { 274 printf("Error: phy device not found.\n"); 275 ret = -ENODEV; 276 goto free_bus; 277 } 278 279 /* get the PHY id */ 280 id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2); 281 id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3); 282 283 if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) { 284 /* re-configure for Micrel KSZ9031 */ 285 printf("configure Micrel KSZ9031 Ethernet Phy at address %d\n", 286 phydev->addr); 287 288 /* phy reset: gpio3-23 */ 289 gpio_set_value(IMX_GPIO_NR(3, 23), 0); 290 gpio_set_value(IMX_GPIO_NR(6, 30), (phydev->addr >> 2)); 291 gpio_set_value(IMX_GPIO_NR(6, 25), 1); 292 gpio_set_value(IMX_GPIO_NR(6, 27), 1); 293 gpio_set_value(IMX_GPIO_NR(6, 28), 1); 294 gpio_set_value(IMX_GPIO_NR(6, 29), 1); 295 SETUP_IOMUX_PADS(enet_pads_ksz9031); 296 gpio_set_value(IMX_GPIO_NR(6, 24), 1); 297 udelay(500); 298 gpio_set_value(IMX_GPIO_NR(3, 23), 1); 299 SETUP_IOMUX_PADS(enet_pads_final_ksz9031); 300 } else if ((id1 == 0x004d) && (id2 == 0xd072)) { 301 /* configure Atheros AR8035 - actually nothing to do */ 302 printf("configure Atheros AR8035 Ethernet Phy at address %d\n", 303 phydev->addr); 304 } else { 305 printf("Unknown Ethernet-Phy: 0x%04x 0x%04x\n", id1, id2); 306 ret = -EINVAL; 307 goto free_phydev; 308 } 309 310 ret = fec_probe(bis, -1, IMX_FEC_BASE, bus, phydev); 311 if (ret) 312 goto free_phydev; 313 314 return 0; 315 316 free_phydev: 317 free(phydev); 318 free_bus: 319 free(bus); 320 return ret; 321 } 322 323 int mx6_rgmii_rework(struct phy_device *phydev) 324 { 325 unsigned short id1, id2; 326 unsigned short val; 327 328 /* check whether KSZ9031 or AR8035 has to be configured */ 329 id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2); 330 id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3); 331 332 if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) { 333 /* finalize phy configuration for Micrel KSZ9031 */ 334 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2); 335 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 4); 336 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2); 337 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x0000); 338 339 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2); 340 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 5); 341 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2); 342 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, MII_KSZ9031_MOD_REG); 343 344 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2); 345 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 6); 346 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2); 347 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0xFFFF); 348 349 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2); 350 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 8); 351 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2); 352 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x3FFF); 353 354 /* fix KSZ9031 link up issue */ 355 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 0x0); 356 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x4); 357 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC); 358 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x6); 359 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_REG); 360 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x3); 361 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC); 362 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x1A80); 363 } 364 365 if ((id1 == 0x004d) && (id2 == 0xd072)) { 366 /* enable AR8035 ouput a 125MHz clk from CLK_25M */ 367 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 0x7); 368 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, MII_KSZ9031_MOD_DATA_POST_INC_RW | 0x16); 369 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC | 0x7); 370 val = phy_read(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA); 371 val &= 0xfe63; 372 val |= 0x18; 373 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, val); 374 375 /* introduce tx clock delay */ 376 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5); 377 val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); 378 val |= 0x0100; 379 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val); 380 381 /* disable hibernation */ 382 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0xb); 383 val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); 384 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3c40); 385 } 386 return 0; 387 } 388 389 int board_phy_config(struct phy_device *phydev) 390 { 391 mx6_rgmii_rework(phydev); 392 393 if (phydev->drv->config) 394 phydev->drv->config(phydev); 395 396 return 0; 397 } 398 399 static void setup_iomux_uart(void) 400 { 401 SETUP_IOMUX_PADS(uart2_pads); 402 } 403 404 #ifdef CONFIG_MXC_SPI 405 static void setup_spi(void) 406 { 407 SETUP_IOMUX_PADS(ecspi1_pads); 408 gpio_direction_output(IMX_GPIO_NR(3, 19), 0); 409 } 410 #endif 411 412 #ifdef CONFIG_FSL_ESDHC 413 static struct fsl_esdhc_cfg usdhc_cfg[] = { 414 {USDHC2_BASE_ADDR}, 415 {USDHC3_BASE_ADDR}, 416 {USDHC4_BASE_ADDR}, 417 }; 418 419 int board_mmc_getcd(struct mmc *mmc) 420 { 421 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 422 int ret = 0; 423 424 switch (cfg->esdhc_base) { 425 case USDHC2_BASE_ADDR: 426 gpio_direction_input(IMX_GPIO_NR(1, 4)); 427 ret = !gpio_get_value(IMX_GPIO_NR(1, 4)); 428 break; 429 case USDHC3_BASE_ADDR: 430 ret = 1; /* eMMC is always present */ 431 break; 432 case USDHC4_BASE_ADDR: 433 gpio_direction_input(IMX_GPIO_NR(2, 6)); 434 ret = !gpio_get_value(IMX_GPIO_NR(2, 6)); 435 break; 436 default: 437 printf("Bad USDHC interface\n"); 438 } 439 440 return ret; 441 } 442 443 int board_mmc_init(bd_t *bis) 444 { 445 #ifndef CONFIG_SPL_BUILD 446 s32 status = 0; 447 int i; 448 449 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 450 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 451 usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); 452 453 SETUP_IOMUX_PADS(usdhc2_pads); 454 SETUP_IOMUX_PADS(usdhc3_pads); 455 SETUP_IOMUX_PADS(usdhc4_pads); 456 457 for (i = 0; i < ARRAY_SIZE(usdhc_cfg); i++) { 458 status = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); 459 if (status) 460 return status; 461 } 462 463 return 0; 464 #else 465 SETUP_IOMUX_PADS(usdhc4_pads); 466 usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR; 467 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); 468 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; 469 470 return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); 471 #endif 472 } 473 #endif 474 475 int board_ehci_hcd_init(int port) 476 { 477 switch (port) { 478 case 0: 479 SETUP_IOMUX_PADS(usb_otg_pads); 480 /* 481 * set daisy chain for otg_pin_id on 6q. 482 * for 6dl, this bit is reserved 483 */ 484 imx_iomux_set_gpr_register(1, 13, 1, 1); 485 break; 486 case 1: 487 /* nothing to do */ 488 break; 489 default: 490 printf("Invalid USB port: %d\n", port); 491 return -EINVAL; 492 } 493 494 return 0; 495 } 496 497 int board_ehci_power(int port, int on) 498 { 499 switch (port) { 500 case 0: 501 break; 502 case 1: 503 gpio_direction_output(IMX_GPIO_NR(5, 5), on); 504 break; 505 default: 506 printf("Invalid USB port: %d\n", port); 507 return -EINVAL; 508 } 509 510 return 0; 511 } 512 513 struct display_info_t { 514 int bus; 515 int addr; 516 int pixfmt; 517 int (*detect)(struct display_info_t const *dev); 518 void (*enable)(struct display_info_t const *dev); 519 struct fb_videomode mode; 520 }; 521 522 static void disable_lvds(struct display_info_t const *dev) 523 { 524 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 525 526 clrbits_le32(&iomux->gpr[2], IOMUXC_GPR2_LVDS_CH0_MODE_MASK | 527 IOMUXC_GPR2_LVDS_CH1_MODE_MASK); 528 } 529 530 static void do_enable_hdmi(struct display_info_t const *dev) 531 { 532 disable_lvds(dev); 533 imx_enable_hdmi_phy(); 534 } 535 536 static struct display_info_t const displays[] = { 537 { 538 .bus = -1, 539 .addr = 0, 540 .pixfmt = IPU_PIX_FMT_RGB666, 541 .detect = NULL, 542 .enable = NULL, 543 .mode = { 544 .name = 545 "Hannstar-XGA", 546 .refresh = 60, 547 .xres = 1024, 548 .yres = 768, 549 .pixclock = 15385, 550 .left_margin = 220, 551 .right_margin = 40, 552 .upper_margin = 21, 553 .lower_margin = 7, 554 .hsync_len = 60, 555 .vsync_len = 10, 556 .sync = FB_SYNC_EXT, 557 .vmode = FB_VMODE_NONINTERLACED } }, 558 { 559 .bus = -1, 560 .addr = 0, 561 .pixfmt = IPU_PIX_FMT_RGB24, 562 .detect = NULL, 563 .enable = do_enable_hdmi, 564 .mode = { 565 .name = "HDMI", 566 .refresh = 60, 567 .xres = 1024, 568 .yres = 768, 569 .pixclock = 15385, 570 .left_margin = 220, 571 .right_margin = 40, 572 .upper_margin = 21, 573 .lower_margin = 7, 574 .hsync_len = 60, 575 .vsync_len = 10, 576 .sync = FB_SYNC_EXT, 577 .vmode = FB_VMODE_NONINTERLACED } } 578 }; 579 580 int board_video_skip(void) 581 { 582 int i; 583 int ret; 584 char const *panel = getenv("panel"); 585 if (!panel) { 586 for (i = 0; i < ARRAY_SIZE(displays); i++) { 587 struct display_info_t const *dev = displays + i; 588 if (dev->detect && dev->detect(dev)) { 589 panel = dev->mode.name; 590 printf("auto-detected panel %s\n", panel); 591 break; 592 } 593 } 594 if (!panel) { 595 panel = displays[0].mode.name; 596 printf("No panel detected: default to %s\n", panel); 597 i = 0; 598 } 599 } else { 600 for (i = 0; i < ARRAY_SIZE(displays); i++) { 601 if (!strcmp(panel, displays[i].mode.name)) 602 break; 603 } 604 } 605 if (i < ARRAY_SIZE(displays)) { 606 ret = ipuv3_fb_init(&displays[i].mode, 0, displays[i].pixfmt); 607 if (!ret) { 608 if (displays[i].enable) 609 displays[i].enable(displays + i); 610 printf("Display: %s (%ux%u)\n", 611 displays[i].mode.name, displays[i].mode.xres, 612 displays[i].mode.yres); 613 } else 614 printf("LCD %s cannot be configured: %d\n", 615 displays[i].mode.name, ret); 616 } else { 617 printf("unsupported panel %s\n", panel); 618 return -EINVAL; 619 } 620 621 return 0; 622 } 623 624 static void setup_display(void) 625 { 626 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 627 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 628 int reg; 629 630 enable_ipu_clock(); 631 imx_setup_hdmi(); 632 633 /* Turn on LDB0, LDB1, IPU,IPU DI0 clocks */ 634 setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK | 635 MXC_CCM_CCGR3_LDB_DI1_MASK); 636 637 /* set LDB0, LDB1 clk select to 011/011 */ 638 reg = readl(&mxc_ccm->cs2cdr); 639 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK | 640 MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 641 reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) | 642 (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); 643 writel(reg, &mxc_ccm->cs2cdr); 644 645 setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV | 646 MXC_CCM_CSCMR2_LDB_DI1_IPU_DIV); 647 648 setbits_le32(&mxc_ccm->chsccdr, CHSCCDR_CLK_SEL_LDB_DI0 << 649 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET | 650 CHSCCDR_CLK_SEL_LDB_DI0 << 651 MXC_CCM_CHSCCDR_IPU1_DI1_CLK_SEL_OFFSET); 652 653 reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES 654 | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW 655 | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW 656 | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG 657 | IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT 658 | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG 659 | IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT 660 | IOMUXC_GPR2_LVDS_CH0_MODE_DISABLED 661 | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0; 662 writel(reg, &iomux->gpr[2]); 663 664 reg = readl(&iomux->gpr[3]); 665 reg = (reg & ~(IOMUXC_GPR3_LVDS1_MUX_CTL_MASK | 666 IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) | 667 (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 << 668 IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET); 669 writel(reg, &iomux->gpr[3]); 670 } 671 672 /* 673 * Do not overwrite the console 674 * Use always serial for U-Boot console 675 */ 676 int overwrite_console(void) 677 { 678 return 1; 679 } 680 681 int board_early_init_f(void) 682 { 683 setup_iomux_uart(); 684 setup_display(); 685 686 #ifdef CONFIG_MXC_SPI 687 setup_spi(); 688 #endif 689 return 0; 690 } 691 692 int board_init(void) 693 { 694 /* address of boot parameters */ 695 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 696 697 698 if (is_mx6dq()) 699 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1); 700 else 701 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1); 702 703 #ifdef CONFIG_CMD_SATA 704 setup_sata(); 705 #endif 706 707 return 0; 708 } 709 710 int checkboard(void) 711 { 712 char *type = "unknown"; 713 714 if (is_cpu_type(MXC_CPU_MX6Q)) 715 type = "Quad"; 716 else if (is_cpu_type(MXC_CPU_MX6D)) 717 type = "Dual"; 718 else if (is_cpu_type(MXC_CPU_MX6DL)) 719 type = "Dual-Lite"; 720 else if (is_cpu_type(MXC_CPU_MX6SOLO)) 721 type = "Solo"; 722 723 printf("Board: conga-QMX6 %s\n", type); 724 725 return 0; 726 } 727 728 #ifdef CONFIG_MXC_SPI 729 int board_spi_cs_gpio(unsigned bus, unsigned cs) 730 { 731 return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -EINVAL; 732 } 733 #endif 734 735 #ifdef CONFIG_CMD_BMODE 736 static const struct boot_mode board_boot_modes[] = { 737 /* 4 bit bus width */ 738 {"mmc0", MAKE_CFGVAL(0x50, 0x20, 0x00, 0x00)}, 739 {"mmc1", MAKE_CFGVAL(0x50, 0x38, 0x00, 0x00)}, 740 {NULL, 0}, 741 }; 742 #endif 743 744 int misc_init_r(void) 745 { 746 #ifdef CONFIG_CMD_BMODE 747 add_board_boot_modes(board_boot_modes); 748 #endif 749 return 0; 750 } 751 752 int board_late_init(void) 753 { 754 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 755 if (is_mx6dq()) 756 setenv("board_rev", "MX6Q"); 757 else 758 setenv("board_rev", "MX6DL"); 759 #endif 760 761 return 0; 762 } 763 764 #ifdef CONFIG_SPL_BUILD 765 #include <asm/arch/mx6-ddr.h> 766 #include <spl.h> 767 #include <libfdt.h> 768 #include <spi_flash.h> 769 #include <spi.h> 770 771 const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = { 772 .dram_sdclk_0 = 0x00000030, 773 .dram_sdclk_1 = 0x00000030, 774 .dram_cas = 0x00000030, 775 .dram_ras = 0x00000030, 776 .dram_reset = 0x00000030, 777 .dram_sdcke0 = 0x00003000, 778 .dram_sdcke1 = 0x00003000, 779 .dram_sdba2 = 0x00000000, 780 .dram_sdodt0 = 0x00000030, 781 .dram_sdodt1 = 0x00000030, 782 .dram_sdqs0 = 0x00000030, 783 .dram_sdqs1 = 0x00000030, 784 .dram_sdqs2 = 0x00000030, 785 .dram_sdqs3 = 0x00000030, 786 .dram_sdqs4 = 0x00000030, 787 .dram_sdqs5 = 0x00000030, 788 .dram_sdqs6 = 0x00000030, 789 .dram_sdqs7 = 0x00000030, 790 .dram_dqm0 = 0x00000030, 791 .dram_dqm1 = 0x00000030, 792 .dram_dqm2 = 0x00000030, 793 .dram_dqm3 = 0x00000030, 794 .dram_dqm4 = 0x00000030, 795 .dram_dqm5 = 0x00000030, 796 .dram_dqm6 = 0x00000030, 797 .dram_dqm7 = 0x00000030, 798 }; 799 800 static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = { 801 .dram_sdclk_0 = 0x00000030, 802 .dram_sdclk_1 = 0x00000030, 803 .dram_cas = 0x00000030, 804 .dram_ras = 0x00000030, 805 .dram_reset = 0x00000030, 806 .dram_sdcke0 = 0x00003000, 807 .dram_sdcke1 = 0x00003000, 808 .dram_sdba2 = 0x00000000, 809 .dram_sdodt0 = 0x00000030, 810 .dram_sdodt1 = 0x00000030, 811 .dram_sdqs0 = 0x00000030, 812 .dram_sdqs1 = 0x00000030, 813 .dram_sdqs2 = 0x00000030, 814 .dram_sdqs3 = 0x00000030, 815 .dram_sdqs4 = 0x00000030, 816 .dram_sdqs5 = 0x00000030, 817 .dram_sdqs6 = 0x00000030, 818 .dram_sdqs7 = 0x00000030, 819 .dram_dqm0 = 0x00000030, 820 .dram_dqm1 = 0x00000030, 821 .dram_dqm2 = 0x00000030, 822 .dram_dqm3 = 0x00000030, 823 .dram_dqm4 = 0x00000030, 824 .dram_dqm5 = 0x00000030, 825 .dram_dqm6 = 0x00000030, 826 .dram_dqm7 = 0x00000030, 827 }; 828 829 const struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = { 830 .grp_ddr_type = 0x000C0000, 831 .grp_ddrmode_ctl = 0x00020000, 832 .grp_ddrpke = 0x00000000, 833 .grp_addds = 0x00000030, 834 .grp_ctlds = 0x00000030, 835 .grp_ddrmode = 0x00020000, 836 .grp_b0ds = 0x00000030, 837 .grp_b1ds = 0x00000030, 838 .grp_b2ds = 0x00000030, 839 .grp_b3ds = 0x00000030, 840 .grp_b4ds = 0x00000030, 841 .grp_b5ds = 0x00000030, 842 .grp_b6ds = 0x00000030, 843 .grp_b7ds = 0x00000030, 844 }; 845 846 static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = { 847 .grp_ddr_type = 0x000c0000, 848 .grp_ddrmode_ctl = 0x00020000, 849 .grp_ddrpke = 0x00000000, 850 .grp_addds = 0x00000030, 851 .grp_ctlds = 0x00000030, 852 .grp_ddrmode = 0x00020000, 853 .grp_b0ds = 0x00000030, 854 .grp_b1ds = 0x00000030, 855 .grp_b2ds = 0x00000030, 856 .grp_b3ds = 0x00000030, 857 .grp_b4ds = 0x00000030, 858 .grp_b5ds = 0x00000030, 859 .grp_b6ds = 0x00000030, 860 .grp_b7ds = 0x00000030, 861 }; 862 863 const struct mx6_mmdc_calibration mx6q_mmcd_calib = { 864 .p0_mpwldectrl0 = 0x0016001A, 865 .p0_mpwldectrl1 = 0x0023001C, 866 .p1_mpwldectrl0 = 0x0028003A, 867 .p1_mpwldectrl1 = 0x001F002C, 868 .p0_mpdgctrl0 = 0x43440354, 869 .p0_mpdgctrl1 = 0x033C033C, 870 .p1_mpdgctrl0 = 0x43300368, 871 .p1_mpdgctrl1 = 0x03500330, 872 .p0_mprddlctl = 0x3228242E, 873 .p1_mprddlctl = 0x2C2C2636, 874 .p0_mpwrdlctl = 0x36323A38, 875 .p1_mpwrdlctl = 0x42324440, 876 }; 877 878 const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = { 879 .p0_mpwldectrl0 = 0x00080016, 880 .p0_mpwldectrl1 = 0x001D0016, 881 .p1_mpwldectrl0 = 0x0018002C, 882 .p1_mpwldectrl1 = 0x000D001D, 883 .p0_mpdgctrl0 = 0x43200334, 884 .p0_mpdgctrl1 = 0x0320031C, 885 .p1_mpdgctrl0 = 0x0344034C, 886 .p1_mpdgctrl1 = 0x03380314, 887 .p0_mprddlctl = 0x3E36383A, 888 .p1_mprddlctl = 0x38363240, 889 .p0_mpwrdlctl = 0x36364238, 890 .p1_mpwrdlctl = 0x4230423E, 891 }; 892 893 static const struct mx6_mmdc_calibration mx6s_mmcd_calib = { 894 .p0_mpwldectrl0 = 0x00480049, 895 .p0_mpwldectrl1 = 0x00410044, 896 .p0_mpdgctrl0 = 0x42480248, 897 .p0_mpdgctrl1 = 0x023C023C, 898 .p0_mprddlctl = 0x40424644, 899 .p0_mpwrdlctl = 0x34323034, 900 }; 901 902 const struct mx6_mmdc_calibration mx6dl_mmcd_calib = { 903 .p0_mpwldectrl0 = 0x0043004B, 904 .p0_mpwldectrl1 = 0x003A003E, 905 .p1_mpwldectrl0 = 0x0047004F, 906 .p1_mpwldectrl1 = 0x004E0061, 907 .p0_mpdgctrl0 = 0x42500250, 908 .p0_mpdgctrl1 = 0x0238023C, 909 .p1_mpdgctrl0 = 0x42640264, 910 .p1_mpdgctrl1 = 0x02500258, 911 .p0_mprddlctl = 0x40424846, 912 .p1_mprddlctl = 0x46484842, 913 .p0_mpwrdlctl = 0x38382C30, 914 .p1_mpwrdlctl = 0x34343430, 915 }; 916 917 static struct mx6_ddr3_cfg mem_ddr_2g = { 918 .mem_speed = 1600, 919 .density = 2, 920 .width = 16, 921 .banks = 8, 922 .rowaddr = 14, 923 .coladdr = 10, 924 .pagesz = 2, 925 .trcd = 1310, 926 .trcmin = 4875, 927 .trasmin = 3500, 928 }; 929 930 static struct mx6_ddr3_cfg mem_ddr_4g = { 931 .mem_speed = 1600, 932 .density = 4, 933 .width = 16, 934 .banks = 8, 935 .rowaddr = 15, 936 .coladdr = 10, 937 .pagesz = 2, 938 .trcd = 1310, 939 .trcmin = 4875, 940 .trasmin = 3500, 941 }; 942 943 static void ccgr_init(void) 944 { 945 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 946 947 writel(0x00C03F3F, &ccm->CCGR0); 948 writel(0x0030FC03, &ccm->CCGR1); 949 writel(0x0FFFC000, &ccm->CCGR2); 950 writel(0x3FF00000, &ccm->CCGR3); 951 writel(0x00FFF300, &ccm->CCGR4); 952 writel(0x0F0000C3, &ccm->CCGR5); 953 writel(0x000003FF, &ccm->CCGR6); 954 } 955 956 static void gpr_init(void) 957 { 958 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 959 960 /* enable AXI cache for VDOA/VPU/IPU */ 961 writel(0xF00000CF, &iomux->gpr[4]); 962 /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ 963 writel(0x007F007F, &iomux->gpr[6]); 964 writel(0x007F007F, &iomux->gpr[7]); 965 } 966 967 /* Define a minimal structure so that the part number can be read via SPL */ 968 struct mfgdata { 969 unsigned char tsize; 970 /* size of checksummed part in bytes */ 971 unsigned char ckcnt; 972 /* checksum corrected byte */ 973 unsigned char cksum; 974 /* decimal serial number, packed BCD */ 975 unsigned char serial[6]; 976 /* part number, right justified, ASCII */ 977 unsigned char pn[16]; 978 }; 979 980 static void conv_ascii(unsigned char *dst, unsigned char *src, int len) 981 { 982 int remain = len; 983 unsigned char *sptr = src; 984 unsigned char *dptr = dst; 985 986 while (remain) { 987 if (*sptr) { 988 *dptr = *sptr; 989 dptr++; 990 } 991 sptr++; 992 remain--; 993 } 994 *dptr = 0x0; 995 } 996 997 #define CFG_MFG_ADDR_OFFSET (spi->size - SZ_16K) 998 static bool is_2gb(void) 999 { 1000 struct spi_flash *spi; 1001 int ret; 1002 char buf[sizeof(struct mfgdata)]; 1003 struct mfgdata *data = (struct mfgdata *)buf; 1004 unsigned char outbuf[32]; 1005 1006 spi = spi_flash_probe(CONFIG_ENV_SPI_BUS, 1007 CONFIG_ENV_SPI_CS, 1008 CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE); 1009 ret = spi_flash_read(spi, CFG_MFG_ADDR_OFFSET, sizeof(struct mfgdata), 1010 buf); 1011 if (ret) 1012 return false; 1013 1014 /* Congatec Part Numbers 104 and 105 have 2GiB of RAM */ 1015 conv_ascii(outbuf, data->pn, sizeof(data->pn)); 1016 if (!memcmp(outbuf, "016104", 6) || !memcmp(outbuf, "016105", 6)) 1017 return true; 1018 else 1019 return false; 1020 } 1021 1022 static void spl_dram_init(int width) 1023 { 1024 struct mx6_ddr_sysinfo sysinfo = { 1025 /* width of data bus:0=16,1=32,2=64 */ 1026 .dsize = width / 32, 1027 /* config for full 4GB range so that get_mem_size() works */ 1028 .cs_density = 32, /* 32Gb per CS */ 1029 /* single chip select */ 1030 .ncs = 1, 1031 .cs1_mirror = 0, 1032 .rtt_wr = 2, 1033 .rtt_nom = 2, 1034 .walat = 0, 1035 .ralat = 5, 1036 .mif3_mode = 3, 1037 .bi_on = 1, 1038 .sde_to_rst = 0x0d, 1039 .rst_to_cke = 0x20, 1040 .refsel = 1, /* Refresh cycles at 32KHz */ 1041 .refr = 7, /* 8 refresh commands per refresh cycle */ 1042 }; 1043 1044 if (is_cpu_type(MXC_CPU_MX6Q) && is_2gb()) { 1045 mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs); 1046 mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g); 1047 return; 1048 } 1049 1050 if (is_mx6dq()) { 1051 mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs); 1052 mx6_dram_cfg(&sysinfo, &mx6q_mmcd_calib, &mem_ddr_2g); 1053 } else if (is_cpu_type(MXC_CPU_MX6SOLO)) { 1054 sysinfo.walat = 1; 1055 mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs); 1056 mx6_dram_cfg(&sysinfo, &mx6s_mmcd_calib, &mem_ddr_4g); 1057 } else if (is_cpu_type(MXC_CPU_MX6DL)) { 1058 sysinfo.walat = 1; 1059 mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs); 1060 mx6_dram_cfg(&sysinfo, &mx6dl_mmcd_calib, &mem_ddr_2g); 1061 } 1062 } 1063 1064 void board_init_f(ulong dummy) 1065 { 1066 /* setup AIPS and disable watchdog */ 1067 arch_cpu_init(); 1068 1069 ccgr_init(); 1070 gpr_init(); 1071 1072 /* iomux and setup of i2c */ 1073 board_early_init_f(); 1074 1075 /* setup GP timer */ 1076 timer_init(); 1077 1078 /* UART clocks enabled and gd valid - init serial console */ 1079 preloader_console_init(); 1080 1081 /* Needed for malloc() to work in SPL prior to board_init_r() */ 1082 spl_init(); 1083 1084 /* DDR initialization */ 1085 if (is_cpu_type(MXC_CPU_MX6SOLO)) 1086 spl_dram_init(32); 1087 else 1088 spl_dram_init(64); 1089 1090 /* Clear the BSS. */ 1091 memset(__bss_start, 0, __bss_end - __bss_start); 1092 1093 /* load/boot image from boot device */ 1094 board_init_r(NULL, 0); 1095 } 1096 #endif 1097