1 /* 2 * Board functions for Compulab CM-T335 board 3 * 4 * Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/ 5 * 6 * Author: Ilya Ledvich <ilya@compulab.co.il> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <errno.h> 13 #include <miiphy.h> 14 #include <cpsw.h> 15 16 #include <asm/arch/sys_proto.h> 17 #include <asm/arch/hardware_am33xx.h> 18 #include <asm/io.h> 19 #include <asm/gpio.h> 20 21 #include "../common/eeprom.h" 22 23 DECLARE_GLOBAL_DATA_PTR; 24 25 /* 26 * Basic board specific setup. Pinmux has been handled already. 27 */ 28 int board_init(void) 29 { 30 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 31 32 gpmc_init(); 33 34 #if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT) 35 status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF); 36 #endif 37 return 0; 38 } 39 40 #if defined (CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD) 41 static void cpsw_control(int enabled) 42 { 43 /* VTP can be added here */ 44 return; 45 } 46 47 static struct cpsw_slave_data cpsw_slave = { 48 .slave_reg_ofs = 0x208, 49 .sliver_reg_ofs = 0xd80, 50 .phy_id = 0, 51 .phy_if = PHY_INTERFACE_MODE_RGMII, 52 }; 53 54 static struct cpsw_platform_data cpsw_data = { 55 .mdio_base = CPSW_MDIO_BASE, 56 .cpsw_base = CPSW_BASE, 57 .mdio_div = 0xff, 58 .channels = 8, 59 .cpdma_reg_ofs = 0x800, 60 .slaves = 1, 61 .slave_data = &cpsw_slave, 62 .ale_reg_ofs = 0xd00, 63 .ale_entries = 1024, 64 .host_port_reg_ofs = 0x108, 65 .hw_stats_reg_ofs = 0x900, 66 .bd_ram_ofs = 0x2000, 67 .mac_control = (1 << 5), 68 .control = cpsw_control, 69 .host_port_num = 0, 70 .version = CPSW_CTRL_VERSION_2, 71 }; 72 73 /* PHY reset GPIO */ 74 #define GPIO_PHY_RST GPIO_PIN(3, 7) 75 76 static void board_phy_init(void) 77 { 78 gpio_request(GPIO_PHY_RST, "phy_rst"); 79 gpio_direction_output(GPIO_PHY_RST, 0); 80 mdelay(2); 81 gpio_set_value(GPIO_PHY_RST, 1); 82 mdelay(2); 83 } 84 85 static void get_efuse_mac_addr(uchar *enetaddr) 86 { 87 uint32_t mac_hi, mac_lo; 88 struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 89 90 mac_lo = readl(&cdev->macid0l); 91 mac_hi = readl(&cdev->macid0h); 92 enetaddr[0] = mac_hi & 0xFF; 93 enetaddr[1] = (mac_hi & 0xFF00) >> 8; 94 enetaddr[2] = (mac_hi & 0xFF0000) >> 16; 95 enetaddr[3] = (mac_hi & 0xFF000000) >> 24; 96 enetaddr[4] = mac_lo & 0xFF; 97 enetaddr[5] = (mac_lo & 0xFF00) >> 8; 98 } 99 100 /* 101 * Routine: handle_mac_address 102 * Description: prepare MAC address for on-board Ethernet. 103 */ 104 static int handle_mac_address(void) 105 { 106 uchar enetaddr[6]; 107 int rv; 108 109 rv = eth_getenv_enetaddr("ethaddr", enetaddr); 110 if (rv) 111 return 0; 112 113 rv = cl_eeprom_read_mac_addr(enetaddr); 114 if (rv) 115 get_efuse_mac_addr(enetaddr); 116 117 if (!is_valid_ether_addr(enetaddr)) 118 return -1; 119 120 return eth_setenv_enetaddr("ethaddr", enetaddr); 121 } 122 123 #define AR8051_PHY_DEBUG_ADDR_REG 0x1d 124 #define AR8051_PHY_DEBUG_DATA_REG 0x1e 125 #define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5 126 #define AR8051_RGMII_TX_CLK_DLY 0x100 127 128 int board_eth_init(bd_t *bis) 129 { 130 int rv, n = 0; 131 const char *devname; 132 struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; 133 134 rv = handle_mac_address(); 135 if (rv) 136 printf("No MAC address found!\n"); 137 138 writel(RGMII_MODE_ENABLE | RGMII_INT_DELAY, &cdev->miisel); 139 140 board_phy_init(); 141 142 rv = cpsw_register(&cpsw_data); 143 if (rv < 0) 144 printf("Error %d registering CPSW switch\n", rv); 145 else 146 n += rv; 147 148 /* 149 * CPSW RGMII Internal Delay Mode is not supported in all PVT 150 * operating points. So we must set the TX clock delay feature 151 * in the AR8051 PHY. Since we only support a single ethernet 152 * device, we only do this for the first instance. 153 */ 154 devname = miiphy_get_current_dev(); 155 156 miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_ADDR_REG, 157 AR8051_DEBUG_RGMII_CLK_DLY_REG); 158 miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_DATA_REG, 159 AR8051_RGMII_TX_CLK_DLY); 160 return n; 161 } 162 #endif /* CONFIG_DRIVER_TI_CPSW && !CONFIG_SPL_BUILD */ 163