1 /* 2 * Board functions for Compulab CM-FX6 board 3 * 4 * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/ 5 * 6 * Author: Nikita Kiryanov <nikita@compulab.co.il> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <dm.h> 13 #include <fsl_esdhc.h> 14 #include <miiphy.h> 15 #include <netdev.h> 16 #include <fdt_support.h> 17 #include <sata.h> 18 #include <asm/arch/crm_regs.h> 19 #include <asm/arch/sys_proto.h> 20 #include <asm/arch/iomux.h> 21 #include <asm/imx-common/mxc_i2c.h> 22 #include <asm/imx-common/sata.h> 23 #include <asm/io.h> 24 #include <asm/gpio.h> 25 #include <dm/platform_data/serial_mxc.h> 26 #include "common.h" 27 #include "../common/eeprom.h" 28 29 DECLARE_GLOBAL_DATA_PTR; 30 31 #ifdef CONFIG_DWC_AHSATA 32 static int cm_fx6_issd_gpios[] = { 33 /* The order of the GPIOs in the array is important! */ 34 CM_FX6_SATA_LDO_EN, 35 CM_FX6_SATA_PHY_SLP, 36 CM_FX6_SATA_NRSTDLY, 37 CM_FX6_SATA_PWREN, 38 CM_FX6_SATA_NSTANDBY1, 39 CM_FX6_SATA_NSTANDBY2, 40 }; 41 42 static void cm_fx6_sata_power(int on) 43 { 44 int i; 45 46 if (!on) { /* tell the iSSD that the power will be removed */ 47 gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 1); 48 mdelay(10); 49 } 50 51 for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) { 52 gpio_direction_output(cm_fx6_issd_gpios[i], on); 53 udelay(100); 54 } 55 56 if (!on) /* for compatibility lower the power loss interrupt */ 57 gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0); 58 } 59 60 static iomux_v3_cfg_t const sata_pads[] = { 61 /* SATA PWR */ 62 IOMUX_PADS(PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)), 63 IOMUX_PADS(PAD_EIM_A22__GPIO2_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL)), 64 IOMUX_PADS(PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL)), 65 IOMUX_PADS(PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)), 66 /* SATA CTRL */ 67 IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)), 68 IOMUX_PADS(PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL)), 69 IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)), 70 IOMUX_PADS(PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)), 71 IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)), 72 }; 73 74 static int cm_fx6_setup_issd(void) 75 { 76 int ret, i; 77 78 SETUP_IOMUX_PADS(sata_pads); 79 80 for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) { 81 ret = gpio_request(cm_fx6_issd_gpios[i], "sata"); 82 if (ret) 83 return ret; 84 } 85 86 ret = gpio_request(CM_FX6_SATA_PWLOSS_INT, "sata_pwloss_int"); 87 if (ret) 88 return ret; 89 90 return 0; 91 } 92 93 #define CM_FX6_SATA_INIT_RETRIES 10 94 int sata_initialize(void) 95 { 96 int err, i; 97 98 /* Make sure this gpio has logical 0 value */ 99 gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0); 100 udelay(100); 101 cm_fx6_sata_power(1); 102 103 for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) { 104 err = setup_sata(); 105 if (err) { 106 printf("SATA setup failed: %d\n", err); 107 return err; 108 } 109 110 udelay(100); 111 112 err = __sata_initialize(); 113 if (!err) 114 break; 115 116 /* There is no device on the SATA port */ 117 if (sata_port_status(0, 0) == 0) 118 break; 119 120 /* There's a device, but link not established. Retry */ 121 } 122 123 return err; 124 } 125 126 int sata_stop(void) 127 { 128 __sata_stop(); 129 cm_fx6_sata_power(0); 130 mdelay(250); 131 132 return 0; 133 } 134 #else 135 static int cm_fx6_setup_issd(void) { return 0; } 136 #endif 137 138 #ifdef CONFIG_SYS_I2C_MXC 139 #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 140 PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 141 PAD_CTL_ODE | PAD_CTL_SRE_FAST) 142 143 I2C_PADS(i2c0_pads, 144 PAD_EIM_D21__I2C1_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL), 145 PAD_EIM_D21__GPIO3_IO21 | MUX_PAD_CTRL(I2C_PAD_CTRL), 146 IMX_GPIO_NR(3, 21), 147 PAD_EIM_D28__I2C1_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL), 148 PAD_EIM_D28__GPIO3_IO28 | MUX_PAD_CTRL(I2C_PAD_CTRL), 149 IMX_GPIO_NR(3, 28)); 150 151 I2C_PADS(i2c1_pads, 152 PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL), 153 PAD_KEY_COL3__GPIO4_IO12 | MUX_PAD_CTRL(I2C_PAD_CTRL), 154 IMX_GPIO_NR(4, 12), 155 PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL), 156 PAD_KEY_ROW3__GPIO4_IO13 | MUX_PAD_CTRL(I2C_PAD_CTRL), 157 IMX_GPIO_NR(4, 13)); 158 159 I2C_PADS(i2c2_pads, 160 PAD_GPIO_3__I2C3_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL), 161 PAD_GPIO_3__GPIO1_IO03 | MUX_PAD_CTRL(I2C_PAD_CTRL), 162 IMX_GPIO_NR(1, 3), 163 PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL), 164 PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(I2C_PAD_CTRL), 165 IMX_GPIO_NR(1, 6)); 166 167 168 static int cm_fx6_setup_one_i2c(int busnum, struct i2c_pads_info *pads) 169 { 170 int ret; 171 172 ret = setup_i2c(busnum, CONFIG_SYS_I2C_SPEED, 0x7f, pads); 173 if (ret) 174 printf("Warning: I2C%d setup failed: %d\n", busnum, ret); 175 176 return ret; 177 } 178 179 static int cm_fx6_setup_i2c(void) 180 { 181 int ret = 0, err; 182 183 /* i2c<x>_pads are wierd macro variables; we can't use an array */ 184 err = cm_fx6_setup_one_i2c(0, I2C_PADS_INFO(i2c0_pads)); 185 if (err) 186 ret = err; 187 err = cm_fx6_setup_one_i2c(1, I2C_PADS_INFO(i2c1_pads)); 188 if (err) 189 ret = err; 190 err = cm_fx6_setup_one_i2c(2, I2C_PADS_INFO(i2c2_pads)); 191 if (err) 192 ret = err; 193 194 return ret; 195 } 196 #else 197 static int cm_fx6_setup_i2c(void) { return 0; } 198 #endif 199 200 #ifdef CONFIG_USB_EHCI_MX6 201 #define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \ 202 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 203 PAD_CTL_HYS | PAD_CTL_SRE_SLOW) 204 #define MX6_USBNC_BASEADDR 0x2184800 205 #define USBNC_USB_H1_PWR_POL (1 << 9) 206 207 static int cm_fx6_setup_usb_host(void) 208 { 209 int err; 210 211 err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst"); 212 if (err) 213 return err; 214 215 SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)); 216 SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL)); 217 218 return 0; 219 } 220 221 static int cm_fx6_setup_usb_otg(void) 222 { 223 int err; 224 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 225 226 err = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr"); 227 if (err) { 228 printf("USB OTG pwr gpio request failed: %d\n", err); 229 return err; 230 } 231 232 SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL)); 233 SETUP_IOMUX_PAD(PAD_ENET_RX_ER__USB_OTG_ID | 234 MUX_PAD_CTRL(WEAK_PULLDOWN)); 235 clrbits_le32(&iomux->gpr[1], IOMUXC_GPR1_OTG_ID_MASK); 236 /* disable ext. charger detect, or it'll affect signal quality at dp. */ 237 return gpio_direction_output(SB_FX6_USB_OTG_PWR, 0); 238 } 239 240 int board_ehci_hcd_init(int port) 241 { 242 int ret; 243 u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4); 244 245 /* Only 1 host controller in use. port 0 is OTG & needs no attention */ 246 if (port != 1) 247 return 0; 248 249 /* Set PWR polarity to match power switch's enable polarity */ 250 setbits_le32(usbnc_usb_uh1_ctrl, USBNC_USB_H1_PWR_POL); 251 ret = gpio_direction_output(CM_FX6_USB_HUB_RST, 0); 252 if (ret) 253 return ret; 254 255 udelay(10); 256 ret = gpio_direction_output(CM_FX6_USB_HUB_RST, 1); 257 if (ret) 258 return ret; 259 260 mdelay(1); 261 262 return 0; 263 } 264 265 int board_ehci_power(int port, int on) 266 { 267 if (port == 0) 268 return gpio_direction_output(SB_FX6_USB_OTG_PWR, on); 269 270 return 0; 271 } 272 #else 273 static int cm_fx6_setup_usb_otg(void) { return 0; } 274 static int cm_fx6_setup_usb_host(void) { return 0; } 275 #endif 276 277 #ifdef CONFIG_FEC_MXC 278 #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 279 PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 280 281 static int mx6_rgmii_rework(struct phy_device *phydev) 282 { 283 unsigned short val; 284 285 /* Ar8031 phy SmartEEE feature cause link status generates glitch, 286 * which cause ethernet link down/up issue, so disable SmartEEE 287 */ 288 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x3); 289 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d); 290 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003); 291 val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); 292 val &= ~(0x1 << 8); 293 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val); 294 295 /* To enable AR8031 ouput a 125MHz clk from CLK_25M */ 296 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); 297 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); 298 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); 299 300 val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); 301 val &= 0xffe3; 302 val |= 0x18; 303 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val); 304 305 /* introduce tx clock delay */ 306 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5); 307 val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); 308 val |= 0x0100; 309 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val); 310 311 return 0; 312 } 313 314 int board_phy_config(struct phy_device *phydev) 315 { 316 mx6_rgmii_rework(phydev); 317 318 if (phydev->drv->config) 319 return phydev->drv->config(phydev); 320 321 return 0; 322 } 323 324 static iomux_v3_cfg_t const enet_pads[] = { 325 IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), 326 IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 327 IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 328 IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 329 IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 330 IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 331 IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 332 IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), 333 IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 334 IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 335 IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 336 IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), 337 IOMUX_PADS(PAD_GPIO_0__CCM_CLKO1 | MUX_PAD_CTRL(NO_PAD_CTRL)), 338 IOMUX_PADS(PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(NO_PAD_CTRL)), 339 IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(0x84)), 340 IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | 341 MUX_PAD_CTRL(ENET_PAD_CTRL)), 342 IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | 343 MUX_PAD_CTRL(ENET_PAD_CTRL)), 344 IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | 345 MUX_PAD_CTRL(ENET_PAD_CTRL)), 346 }; 347 348 static int handle_mac_address(void) 349 { 350 unsigned char enetaddr[6]; 351 int rc; 352 353 rc = eth_getenv_enetaddr("ethaddr", enetaddr); 354 if (rc) 355 return 0; 356 357 rc = cl_eeprom_read_mac_addr(enetaddr); 358 if (rc) 359 return rc; 360 361 if (!is_valid_ether_addr(enetaddr)) 362 return -1; 363 364 return eth_setenv_enetaddr("ethaddr", enetaddr); 365 } 366 367 int board_eth_init(bd_t *bis) 368 { 369 int err; 370 371 err = handle_mac_address(); 372 if (err) 373 puts("No MAC address found\n"); 374 375 SETUP_IOMUX_PADS(enet_pads); 376 /* phy reset */ 377 err = gpio_request(CM_FX6_ENET_NRST, "enet_nrst"); 378 if (err) 379 printf("Etnernet NRST gpio request failed: %d\n", err); 380 gpio_direction_output(CM_FX6_ENET_NRST, 0); 381 udelay(500); 382 gpio_set_value(CM_FX6_ENET_NRST, 1); 383 enable_enet_clk(1); 384 return cpu_eth_init(bis); 385 } 386 #endif 387 388 #ifdef CONFIG_NAND_MXS 389 static iomux_v3_cfg_t const nand_pads[] = { 390 IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL)), 391 IOMUX_PADS(PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL)), 392 IOMUX_PADS(PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL)), 393 IOMUX_PADS(PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL)), 394 IOMUX_PADS(PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL)), 395 IOMUX_PADS(PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL)), 396 IOMUX_PADS(PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL)), 397 IOMUX_PADS(PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL)), 398 IOMUX_PADS(PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL)), 399 IOMUX_PADS(PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL)), 400 IOMUX_PADS(PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL)), 401 IOMUX_PADS(PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL)), 402 IOMUX_PADS(PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL)), 403 IOMUX_PADS(PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL)), 404 }; 405 406 static void cm_fx6_setup_gpmi_nand(void) 407 { 408 SETUP_IOMUX_PADS(nand_pads); 409 /* Enable clock roots */ 410 enable_usdhc_clk(1, 3); 411 enable_usdhc_clk(1, 4); 412 413 setup_gpmi_io_clk(MXC_CCM_CS2CDR_ENFC_CLK_PODF(0xf) | 414 MXC_CCM_CS2CDR_ENFC_CLK_PRED(1) | 415 MXC_CCM_CS2CDR_ENFC_CLK_SEL(0)); 416 } 417 #else 418 static void cm_fx6_setup_gpmi_nand(void) {} 419 #endif 420 421 #ifdef CONFIG_FSL_ESDHC 422 static struct fsl_esdhc_cfg usdhc_cfg[3] = { 423 {USDHC1_BASE_ADDR}, 424 {USDHC2_BASE_ADDR}, 425 {USDHC3_BASE_ADDR}, 426 }; 427 428 static enum mxc_clock usdhc_clk[3] = { 429 MXC_ESDHC_CLK, 430 MXC_ESDHC2_CLK, 431 MXC_ESDHC3_CLK, 432 }; 433 434 int board_mmc_init(bd_t *bis) 435 { 436 int i; 437 438 cm_fx6_set_usdhc_iomux(); 439 for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { 440 usdhc_cfg[i].sdhc_clk = mxc_get_clock(usdhc_clk[i]); 441 usdhc_cfg[i].max_bus_width = 4; 442 fsl_esdhc_initialize(bis, &usdhc_cfg[i]); 443 enable_usdhc_clk(1, i); 444 } 445 446 return 0; 447 } 448 #endif 449 450 #ifdef CONFIG_MXC_SPI 451 int cm_fx6_setup_ecspi(void) 452 { 453 cm_fx6_set_ecspi_iomux(); 454 return gpio_request(CM_FX6_ECSPI_BUS0_CS0, "ecspi_bus0_cs0"); 455 } 456 #else 457 int cm_fx6_setup_ecspi(void) { return 0; } 458 #endif 459 460 #ifdef CONFIG_OF_BOARD_SETUP 461 int ft_board_setup(void *blob, bd_t *bd) 462 { 463 uint8_t enetaddr[6]; 464 465 /* MAC addr */ 466 if (eth_getenv_enetaddr("ethaddr", enetaddr)) { 467 fdt_find_and_setprop(blob, "/fec", "local-mac-address", 468 enetaddr, 6, 1); 469 } 470 471 return 0; 472 } 473 #endif 474 475 int board_init(void) 476 { 477 int ret; 478 479 gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; 480 cm_fx6_setup_gpmi_nand(); 481 482 ret = cm_fx6_setup_ecspi(); 483 if (ret) 484 printf("Warning: ECSPI setup failed: %d\n", ret); 485 486 ret = cm_fx6_setup_usb_otg(); 487 if (ret) 488 printf("Warning: USB OTG setup failed: %d\n", ret); 489 490 ret = cm_fx6_setup_usb_host(); 491 if (ret) 492 printf("Warning: USB host setup failed: %d\n", ret); 493 494 /* 495 * cm-fx6 may have iSSD not assembled and in this case it has 496 * bypasses for a (m)SATA socket on the baseboard. The socketed 497 * device is not controlled by those GPIOs. So just print a warning 498 * if the setup fails. 499 */ 500 ret = cm_fx6_setup_issd(); 501 if (ret) 502 printf("Warning: iSSD setup failed: %d\n", ret); 503 504 /* Warn on failure but do not abort boot */ 505 ret = cm_fx6_setup_i2c(); 506 if (ret) 507 printf("Warning: I2C setup failed: %d\n", ret); 508 509 return 0; 510 } 511 512 int checkboard(void) 513 { 514 puts("Board: CM-FX6\n"); 515 return 0; 516 } 517 518 void dram_init_banksize(void) 519 { 520 gd->bd->bi_dram[0].start = PHYS_SDRAM_1; 521 gd->bd->bi_dram[1].start = PHYS_SDRAM_2; 522 523 switch (gd->ram_size) { 524 case 0x10000000: /* DDR_16BIT_256MB */ 525 gd->bd->bi_dram[0].size = 0x10000000; 526 gd->bd->bi_dram[1].size = 0; 527 break; 528 case 0x20000000: /* DDR_32BIT_512MB */ 529 gd->bd->bi_dram[0].size = 0x20000000; 530 gd->bd->bi_dram[1].size = 0; 531 break; 532 case 0x40000000: 533 if (is_cpu_type(MXC_CPU_MX6SOLO)) { /* DDR_32BIT_1GB */ 534 gd->bd->bi_dram[0].size = 0x20000000; 535 gd->bd->bi_dram[1].size = 0x20000000; 536 } else { /* DDR_64BIT_1GB */ 537 gd->bd->bi_dram[0].size = 0x40000000; 538 gd->bd->bi_dram[1].size = 0; 539 } 540 break; 541 case 0x80000000: /* DDR_64BIT_2GB */ 542 gd->bd->bi_dram[0].size = 0x40000000; 543 gd->bd->bi_dram[1].size = 0x40000000; 544 break; 545 case 0xEFF00000: /* DDR_64BIT_4GB */ 546 gd->bd->bi_dram[0].size = 0x70000000; 547 gd->bd->bi_dram[1].size = 0x7FF00000; 548 break; 549 } 550 } 551 552 int dram_init(void) 553 { 554 gd->ram_size = imx_ddr_size(); 555 switch (gd->ram_size) { 556 case 0x10000000: 557 case 0x20000000: 558 case 0x40000000: 559 case 0x80000000: 560 break; 561 case 0xF0000000: 562 gd->ram_size -= 0x100000; 563 break; 564 default: 565 printf("ERROR: Unsupported DRAM size 0x%lx\n", gd->ram_size); 566 return -1; 567 } 568 569 return 0; 570 } 571 572 u32 get_board_rev(void) 573 { 574 return cl_eeprom_get_board_rev(); 575 } 576 577 static struct mxc_serial_platdata cm_fx6_mxc_serial_plat = { 578 .reg = (struct mxc_uart *)UART4_BASE, 579 }; 580 581 U_BOOT_DEVICE(cm_fx6_serial) = { 582 .name = "serial_mxc", 583 .platdata = &cm_fx6_mxc_serial_plat, 584 }; 585