1#
2# Copyright (C) 2012
3# David Purdy <david.c.purdy@gmail.com>
4#
5# Based on Kirkwood support:
6# (C) Copyright 2009
7# Marvell Semiconductor <www.marvell.com>
8# Written-by: Prafulla Wadaskar <prafulla <at> marvell.com>
9#
10# SPDX-License-Identifier:	GPL-2.0+
11#
12# Refer doc/README.kwbimage for more details about how-to configure
13# and create kirkwood boot image
14#
15
16# Boot Media configurations
17BOOT_FROM	nand
18NAND_ECC_MODE	default
19NAND_PAGE_SIZE	0x0800
20
21# SOC registers configuration using bootrom header extension
22# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
23
24# Configure RGMII-0 interface pad voltage to 1.8V
25DATA 0xffd100e0 0x1b1b1b9b
26
27#Dram initalization for SINGLE x16 CL=5 @ 400MHz
28DATA 0xffd01400 0x43000c30	# DDR Configuration register
29# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
30# bit23-14: zero
31# bit24: 1= enable exit self refresh mode on DDR access
32# bit25: 1 required
33# bit29-26: zero
34# bit31-30: 01
35
36DATA 0xffd01404 0x37543000	# DDR Controller Control Low
37# bit 4:    0=addr/cmd in smame cycle
38# bit 5:    0=clk is driven during self refresh, we don't care for APX
39# bit 6:    0=use recommended falling edge of clk for addr/cmd
40# bit14:    0=input buffer always powered up
41# bit18:    1=cpu lock transaction enabled
42# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
43# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
44# bit30-28: 3 required
45# bit31:    0=no additional STARTBURST delay
46
47DATA 0xffd01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
48# bit3-0:   TRAS lsbs
49# bit7-4:   TRCD
50# bit11- 8: TRP
51# bit15-12: TWR
52# bit19-16: TWTR
53# bit20:    TRAS msb
54# bit23-21: 0x0
55# bit27-24: TRRD
56# bit31-28: TRTP
57
58DATA 0xffd0140c 0x00000a33	#  DDR Timing (High)
59# bit6-0:   TRFC
60# bit8-7:   TR2R
61# bit10-9:  TR2W
62# bit12-11: TW2W
63# bit31-13: zero required
64
65DATA 0xffd01410 0x000000cc	#  DDR Address Control
66# bit1-0:   00, Cs0width=x8
67# bit3-2:   11, Cs0size=1Gb
68# bit5-4:   00, Cs1width=x8
69# bit7-6:   11, Cs1size=1Gb
70# bit9-8:   00, Cs2width=nonexistent
71# bit11-10: 00, Cs2size =nonexistent
72# bit13-12: 00, Cs3width=nonexistent
73# bit15-14: 00, Cs3size =nonexistent
74# bit16:    0,  Cs0AddrSel
75# bit17:    0,  Cs1AddrSel
76# bit18:    0,  Cs2AddrSel
77# bit19:    0,  Cs3AddrSel
78# bit31-20: 0 required
79
80DATA 0xffd01414 0x00000000	#  DDR Open Pages Control
81# bit0:    0,  OpenPage enabled
82# bit31-1: 0 required
83
84DATA 0xffd01418 0x00000000	#  DDR Operation
85# bit3-0:   0x0, DDR cmd
86# bit31-4:  0 required
87
88DATA 0xffd0141c 0x00000c52	#  DDR Mode
89# bit2-0:   2, BurstLen=2 required
90# bit3:     0, BurstType=0 required
91# bit6-4:   4, CL=5
92# bit7:     0, TestMode=0 normal
93# bit8:     0, DLL reset=0 normal
94# bit11-9:  6, auto-precharge write recovery ????????????
95# bit12:    0, PD must be zero
96# bit31-13: 0 required
97
98DATA 0xffd01420 0x00000040	#  DDR Extended Mode
99# bit0:    0,  DDR DLL enabled
100# bit1:    0,  DDR drive strenght normal
101# bit2:    0,  DDR ODT control lsd (disabled)
102# bit5-3:  000, required
103# bit6:    1,  DDR ODT control msb, (disabled)
104# bit9-7:  000, required
105# bit10:   0,  differential DQS enabled
106# bit11:   0, required
107# bit12:   0, DDR output buffer enabled
108# bit31-13: 0 required
109
110DATA 0xffd01424 0x0000f17f	#  DDR Controller Control High
111# bit2-0:  111, required
112# bit3  :  1  , MBUS Burst Chop disabled
113# bit6-4:  111, required
114# bit7  :  0
115# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
116# bit9  :  0  , no half clock cycle addition to dataout
117# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
118# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
119# bit15-12: 1111 required
120# bit31-16: 0    required
121
122DATA 0xffd01428 0x00085520	# DDR2 ODT Read Timing (default values)
123DATA 0xffd0147c 0x00008552	# DDR2 ODT Write Timing (default values)
124
125DATA 0xffd01500 0x00000000	# CS[0]n Base address to 0x0
126DATA 0xffd01504 0x0ffffff1	# CS[0]n Size
127# bit0:    1,  Window enabled
128# bit1:    0,  Write Protect disabled
129# bit3-2:  00, CS0 hit selected
130# bit23-4: ones, required
131# bit31-24: 0x0F, Size (i.e. 256MB)
132
133DATA 0xffd01508 0x10000000	# CS[1]n Base address to 256Mb
134DATA 0xffd0150c 0x00000000	# CS[2]n Size, window disabled
135
136DATA 0xffd01514 0x00000000	# CS[2]n Size, window disabled
137DATA 0xffd0151c 0x00000000	# CS[3]n Size, window disabled
138
139DATA 0xffd01494 0x00030000	#  DDR ODT Control (Low)
140# bit3-0:  2, ODT0Rd, MODT[0] asserted during read from DRAM CS1
141# bit7-4:  1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
142# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
143# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
144
145DATA 0xffd01498 0x00000000	#  DDR ODT Control (High)
146# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
147# bit3-2:  01, ODT1 active NEVER!
148# bit31-4: zero, required
149
150DATA 0xffd0149c 0x0000e803	# CPU ODT Control
151DATA 0xffd01480 0x00000001	# DDR Initialization Control
152#bit0=1, enable DDR init upon this register write
153
154# End of Header extension
155DATA 0x0 0x0
156