1 /* 2 * (C) Copyright 2007-2013 3 * Stelian Pop <stelian.pop@leadtechdesign.com> 4 * Lead Tech Design <www.leadtechdesign.com> 5 * Thomas Petazzoni, Free Electrons, <thomas.petazzoni@free-electrons.com> 6 * Mateusz Kulikowski <mateusz.kulikowski@gmail.com> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <asm/arch/at91sam9_smc.h> 13 #include <asm/arch/at91_common.h> 14 #include <asm/arch/at91_matrix.h> 15 #include <asm/arch/at91_pmc.h> 16 #include <asm/arch/gpio.h> 17 #include <asm-generic/gpio.h> 18 #include <asm/io.h> 19 #include <net.h> 20 #include <netdev.h> 21 #include <dataflash.h> 22 23 DECLARE_GLOBAL_DATA_PTR; 24 25 #ifdef CONFIG_HAS_DATAFLASH 26 AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS]; 27 28 struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = { 29 {CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0, 0}, /* Logical adress, CS */ 30 }; 31 32 /*define the area offsets*/ 33 dataflash_protect_t area_list[NB_DATAFLASH_AREA] = { 34 {0x00000000, 0x00001FFF, FLAG_PROTECT_SET, 0, "Bootstrap"}, 35 {0x00002000, 0x00003FFF, FLAG_PROTECT_CLEAR, 0, "Environment"}, 36 {0x00004000, 0xFFFFFFFF, FLAG_PROTECT_CLEAR, 0, "U-Boot"}, 37 }; 38 #endif 39 40 #ifdef CONFIG_CMD_NAND 41 static void usb_a9263_nand_hw_init(void) 42 { 43 unsigned long csa; 44 at91_smc_t *smc = (at91_smc_t *)ATMEL_BASE_SMC0; 45 at91_matrix_t *matrix = (at91_matrix_t *)ATMEL_BASE_MATRIX; 46 at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC; 47 48 /* Enable CS3 */ 49 csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A; 50 writel(csa, &matrix->csa[0]); 51 52 /* Configure SMC CS3 for NAND/SmartMedia */ 53 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | 54 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), 55 &smc->cs[3].setup); 56 57 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | 58 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), 59 &smc->cs[3].pulse); 60 61 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), 62 &smc->cs[3].cycle); 63 64 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 65 AT91_SMC_MODE_EXNW_DISABLE | 66 AT91_SMC_MODE_DBW_8 | 67 AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode); 68 69 writel(1 << ATMEL_ID_PIOA | 1 << ATMEL_ID_PIOCDE, &pmc->pcer); 70 71 /* Configure RDY/BSY */ 72 gpio_request(CONFIG_SYS_NAND_READY_PIN, "NAND ready/busy"); 73 gpio_direction_input(CONFIG_SYS_NAND_READY_PIN); 74 75 /* Enable NandFlash */ 76 gpio_request(CONFIG_SYS_NAND_ENABLE_PIN, "NAND enable"); 77 gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); 78 } 79 #endif 80 81 #ifdef CONFIG_MACB 82 static void usb_a9263_macb_hw_init(void) 83 { 84 at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC; 85 86 /* Enable clock */ 87 writel(1 << ATMEL_ID_EMAC, &pmc->pcer); 88 89 /* 90 * Disable pull-up on: 91 * RXDV (PC25) => PHY normal mode (not Test mode) 92 * ERX0 (PE25) => PHY ADDR0 93 * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0 94 * 95 * PHY has internal weak pull-up/pull-down 96 */ 97 gpio_request(GPIO_PIN_PC(25), "PHY mode"); 98 gpio_direction_input(GPIO_PIN_PC(25)); 99 100 gpio_request(GPIO_PIN_PE(25), "PHY ADDR0"); 101 gpio_direction_input(GPIO_PIN_PE(25)); 102 103 gpio_request(GPIO_PIN_PE(26), "PHY ADDR1"); 104 gpio_direction_input(GPIO_PIN_PE(26)); 105 106 at91_phy_reset(); 107 108 /* It will set proper pinmux for ports PC25, PE25-26 */ 109 at91_macb_hw_init(); 110 } 111 #endif 112 113 int board_init(void) 114 { 115 /* adress of boot parameters */ 116 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 117 118 #ifdef CONFIG_CMD_NAND 119 usb_a9263_nand_hw_init(); 120 #endif 121 #ifdef CONFIG_HAS_DATAFLASH 122 at91_spi0_hw_init(1 << 0); 123 #endif 124 #ifdef CONFIG_MACB 125 usb_a9263_macb_hw_init(); 126 #endif 127 #ifdef CONFIG_USB_OHCI_NEW 128 at91_uhp_hw_init(); 129 #endif 130 return 0; 131 } 132 133 int dram_init(void) 134 { 135 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 136 CONFIG_SYS_SDRAM_SIZE); 137 return 0; 138 } 139 140 int board_eth_init(bd_t *bis) 141 { 142 int rc = 0; 143 144 #ifdef CONFIG_MACB 145 rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x0001); 146 #endif 147 return rc; 148 } 149