1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2010-2013 Freescale Semiconductor, Inc. 4 * Copyright (C) 2013, Boundary Devices <info@boundarydevices.com> 5 */ 6 7 #include <common.h> 8 #include <asm/io.h> 9 #include <asm/arch/clock.h> 10 #include <asm/arch/imx-regs.h> 11 #include <asm/arch/iomux.h> 12 #include <asm/arch/sys_proto.h> 13 #include <malloc.h> 14 #include <asm/arch/mx6-pins.h> 15 #include <linux/errno.h> 16 #include <asm/gpio.h> 17 #include <asm/mach-imx/iomux-v3.h> 18 #include <asm/mach-imx/mxc_i2c.h> 19 #include <asm/mach-imx/sata.h> 20 #include <asm/mach-imx/spi.h> 21 #include <asm/mach-imx/boot_mode.h> 22 #include <asm/mach-imx/video.h> 23 #include <mmc.h> 24 #include <fsl_esdhc.h> 25 #include <micrel.h> 26 #include <miiphy.h> 27 #include <netdev.h> 28 #include <asm/arch/crm_regs.h> 29 #include <asm/arch/mxc_hdmi.h> 30 #include <i2c.h> 31 #include <input.h> 32 #include <netdev.h> 33 #include <usb/ehci-ci.h> 34 35 DECLARE_GLOBAL_DATA_PTR; 36 #define GP_USB_OTG_PWR IMX_GPIO_NR(3, 22) 37 38 #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 39 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 40 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 41 42 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ 43 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ 44 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 45 46 #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 47 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 48 49 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ 50 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 51 52 #define BUTTON_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 53 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) 54 55 #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ 56 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 57 PAD_CTL_ODE | PAD_CTL_SRE_FAST) 58 59 #define WEAK_PULLUP (PAD_CTL_PUS_100K_UP | \ 60 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ 61 PAD_CTL_SRE_SLOW) 62 63 #define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \ 64 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ 65 PAD_CTL_HYS | PAD_CTL_SRE_SLOW) 66 67 #define OUTPUT_40OHM (PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm) 68 69 int dram_init(void) 70 { 71 gd->ram_size = ((ulong)CONFIG_DDR_MB * 1024 * 1024); 72 73 return 0; 74 } 75 76 static iomux_v3_cfg_t const uart1_pads[] = { 77 MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 78 MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 79 }; 80 81 static iomux_v3_cfg_t const uart2_pads[] = { 82 MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 83 MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 84 }; 85 86 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) 87 88 /* I2C1, SGTL5000 */ 89 static struct i2c_pads_info i2c_pad_info0 = { 90 .scl = { 91 .i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC, 92 .gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC, 93 .gp = IMX_GPIO_NR(3, 21) 94 }, 95 .sda = { 96 .i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC, 97 .gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC, 98 .gp = IMX_GPIO_NR(3, 28) 99 } 100 }; 101 102 /* I2C2 Camera, MIPI */ 103 static struct i2c_pads_info i2c_pad_info1 = { 104 .scl = { 105 .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC, 106 .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC, 107 .gp = IMX_GPIO_NR(4, 12) 108 }, 109 .sda = { 110 .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC, 111 .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC, 112 .gp = IMX_GPIO_NR(4, 13) 113 } 114 }; 115 116 /* I2C3, J15 - RGB connector */ 117 static struct i2c_pads_info i2c_pad_info2 = { 118 .scl = { 119 .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC, 120 .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC, 121 .gp = IMX_GPIO_NR(1, 5) 122 }, 123 .sda = { 124 .i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | PC, 125 .gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | PC, 126 .gp = IMX_GPIO_NR(7, 11) 127 } 128 }; 129 130 static iomux_v3_cfg_t const usdhc2_pads[] = { 131 MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 132 MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 133 MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 134 MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 135 MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 136 MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 137 }; 138 139 static iomux_v3_cfg_t const usdhc3_pads[] = { 140 MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 141 MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 142 MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 143 MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 144 MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 145 MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 146 MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ 147 }; 148 149 static iomux_v3_cfg_t const usdhc4_pads[] = { 150 MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 151 MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 152 MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 153 MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 154 MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 155 MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 156 MX6_PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ 157 }; 158 159 static iomux_v3_cfg_t const enet_pads1[] = { 160 MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 161 MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 162 MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 163 MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 164 MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 165 MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 166 MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 167 MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 168 MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), 169 /* pin 35 - 1 (PHY_AD2) on reset */ 170 MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), 171 /* pin 32 - 1 - (MODE0) all */ 172 MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL), 173 /* pin 31 - 1 - (MODE1) all */ 174 MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), 175 /* pin 28 - 1 - (MODE2) all */ 176 MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), 177 /* pin 27 - 1 - (MODE3) all */ 178 MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), 179 /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */ 180 MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL), 181 /* pin 42 PHY nRST */ 182 MX6_PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL), 183 MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), 184 }; 185 186 static iomux_v3_cfg_t const enet_pads2[] = { 187 MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 188 MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 189 MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 190 MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 191 MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 192 MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 193 }; 194 195 static iomux_v3_cfg_t const misc_pads[] = { 196 MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(WEAK_PULLUP), 197 MX6_PAD_KEY_COL4__USB_OTG_OC | MUX_PAD_CTRL(WEAK_PULLUP), 198 MX6_PAD_EIM_D30__USB_H1_OC | MUX_PAD_CTRL(WEAK_PULLUP), 199 /* OTG Power enable */ 200 MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(OUTPUT_40OHM), 201 }; 202 203 /* wl1271 pads on nitrogen6x */ 204 static iomux_v3_cfg_t const wl12xx_pads[] = { 205 (MX6_PAD_NANDF_CS1__GPIO6_IO14 & ~MUX_PAD_CTRL_MASK) 206 | MUX_PAD_CTRL(WEAK_PULLDOWN), 207 (MX6_PAD_NANDF_CS2__GPIO6_IO15 & ~MUX_PAD_CTRL_MASK) 208 | MUX_PAD_CTRL(OUTPUT_40OHM), 209 (MX6_PAD_NANDF_CS3__GPIO6_IO16 & ~MUX_PAD_CTRL_MASK) 210 | MUX_PAD_CTRL(OUTPUT_40OHM), 211 }; 212 #define WL12XX_WL_IRQ_GP IMX_GPIO_NR(6, 14) 213 #define WL12XX_WL_ENABLE_GP IMX_GPIO_NR(6, 15) 214 #define WL12XX_BT_ENABLE_GP IMX_GPIO_NR(6, 16) 215 216 /* Button assignments for J14 */ 217 static iomux_v3_cfg_t const button_pads[] = { 218 /* Menu */ 219 MX6_PAD_NANDF_D1__GPIO2_IO01 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), 220 /* Back */ 221 MX6_PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), 222 /* Labelled Search (mapped to Power under Android) */ 223 MX6_PAD_NANDF_D3__GPIO2_IO03 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), 224 /* Home */ 225 MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), 226 /* Volume Down */ 227 MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), 228 /* Volume Up */ 229 MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), 230 }; 231 232 static void setup_iomux_enet(void) 233 { 234 gpio_direction_output(IMX_GPIO_NR(3, 23), 0); /* SABRE Lite PHY rst */ 235 gpio_direction_output(IMX_GPIO_NR(1, 27), 0); /* Nitrogen6X PHY rst */ 236 gpio_direction_output(IMX_GPIO_NR(6, 30), 1); 237 gpio_direction_output(IMX_GPIO_NR(6, 25), 1); 238 gpio_direction_output(IMX_GPIO_NR(6, 27), 1); 239 gpio_direction_output(IMX_GPIO_NR(6, 28), 1); 240 gpio_direction_output(IMX_GPIO_NR(6, 29), 1); 241 imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1)); 242 gpio_direction_output(IMX_GPIO_NR(6, 24), 1); 243 244 /* Need delay 10ms according to KSZ9021 spec */ 245 udelay(1000 * 10); 246 gpio_set_value(IMX_GPIO_NR(3, 23), 1); /* SABRE Lite PHY reset */ 247 gpio_set_value(IMX_GPIO_NR(1, 27), 1); /* Nitrogen6X PHY reset */ 248 249 imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2)); 250 udelay(100); /* Wait 100 us before using mii interface */ 251 } 252 253 static iomux_v3_cfg_t const usb_pads[] = { 254 MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), 255 }; 256 257 static void setup_iomux_uart(void) 258 { 259 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); 260 imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); 261 } 262 263 #ifdef CONFIG_USB_EHCI_MX6 264 int board_ehci_hcd_init(int port) 265 { 266 imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads)); 267 268 /* Reset USB hub */ 269 gpio_direction_output(IMX_GPIO_NR(7, 12), 0); 270 mdelay(2); 271 gpio_set_value(IMX_GPIO_NR(7, 12), 1); 272 273 return 0; 274 } 275 276 int board_ehci_power(int port, int on) 277 { 278 if (port) 279 return 0; 280 gpio_set_value(GP_USB_OTG_PWR, on); 281 return 0; 282 } 283 284 #endif 285 286 #ifdef CONFIG_FSL_ESDHC 287 static struct fsl_esdhc_cfg usdhc_cfg[2] = { 288 {USDHC3_BASE_ADDR}, 289 {USDHC4_BASE_ADDR}, 290 }; 291 292 int board_mmc_getcd(struct mmc *mmc) 293 { 294 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 295 int gp_cd = (cfg->esdhc_base == USDHC3_BASE_ADDR) ? IMX_GPIO_NR(7, 0) : 296 IMX_GPIO_NR(2, 6); 297 298 gpio_direction_input(gp_cd); 299 return !gpio_get_value(gp_cd); 300 } 301 302 int board_mmc_init(bd_t *bis) 303 { 304 int ret; 305 u32 index = 0; 306 307 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 308 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); 309 310 usdhc_cfg[0].max_bus_width = 4; 311 usdhc_cfg[1].max_bus_width = 4; 312 313 for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { 314 switch (index) { 315 case 0: 316 imx_iomux_v3_setup_multiple_pads( 317 usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); 318 break; 319 case 1: 320 imx_iomux_v3_setup_multiple_pads( 321 usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); 322 break; 323 default: 324 printf("Warning: you configured more USDHC controllers" 325 "(%d) then supported by the board (%d)\n", 326 index + 1, CONFIG_SYS_FSL_USDHC_NUM); 327 return -EINVAL; 328 } 329 330 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]); 331 if (ret) 332 return ret; 333 } 334 335 return 0; 336 } 337 #endif 338 339 #ifdef CONFIG_MXC_SPI 340 int board_spi_cs_gpio(unsigned bus, unsigned cs) 341 { 342 return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -1; 343 } 344 345 static iomux_v3_cfg_t const ecspi1_pads[] = { 346 /* SS1 */ 347 MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), 348 MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), 349 MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), 350 MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), 351 }; 352 353 static void setup_spi(void) 354 { 355 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, 356 ARRAY_SIZE(ecspi1_pads)); 357 } 358 #endif 359 360 int board_phy_config(struct phy_device *phydev) 361 { 362 /* min rx data delay */ 363 ksz9021_phy_extended_write(phydev, 364 MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW, 0x0); 365 /* min tx data delay */ 366 ksz9021_phy_extended_write(phydev, 367 MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW, 0x0); 368 /* max rx/tx clock delay, min rx/tx control */ 369 ksz9021_phy_extended_write(phydev, 370 MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, 0xf0f0); 371 if (phydev->drv->config) 372 phydev->drv->config(phydev); 373 374 return 0; 375 } 376 377 int board_eth_init(bd_t *bis) 378 { 379 uint32_t base = IMX_FEC_BASE; 380 struct mii_dev *bus = NULL; 381 struct phy_device *phydev = NULL; 382 int ret; 383 384 setup_iomux_enet(); 385 386 #ifdef CONFIG_FEC_MXC 387 bus = fec_get_miibus(base, -1); 388 if (!bus) 389 return -EINVAL; 390 /* scan phy 4,5,6,7 */ 391 phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII); 392 if (!phydev) { 393 ret = -EINVAL; 394 goto free_bus; 395 } 396 printf("using phy at %d\n", phydev->addr); 397 ret = fec_probe(bis, -1, base, bus, phydev); 398 if (ret) 399 goto free_phydev; 400 #endif 401 402 #ifdef CONFIG_CI_UDC 403 /* For otg ethernet*/ 404 usb_eth_initialize(bis); 405 #endif 406 return 0; 407 408 free_phydev: 409 free(phydev); 410 free_bus: 411 free(bus); 412 return ret; 413 } 414 415 static void setup_buttons(void) 416 { 417 imx_iomux_v3_setup_multiple_pads(button_pads, 418 ARRAY_SIZE(button_pads)); 419 } 420 421 #if defined(CONFIG_VIDEO_IPUV3) 422 423 static iomux_v3_cfg_t const backlight_pads[] = { 424 /* Backlight on RGB connector: J15 */ 425 MX6_PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL), 426 #define RGB_BACKLIGHT_GP IMX_GPIO_NR(1, 21) 427 428 /* Backlight on LVDS connector: J6 */ 429 MX6_PAD_SD1_CMD__GPIO1_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL), 430 #define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 18) 431 }; 432 433 static iomux_v3_cfg_t const rgb_pads[] = { 434 MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK, 435 MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, 436 MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, 437 MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, 438 MX6_PAD_DI0_PIN4__GPIO4_IO20, 439 MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00, 440 MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01, 441 MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02, 442 MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03, 443 MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04, 444 MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05, 445 MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06, 446 MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07, 447 MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08, 448 MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09, 449 MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10, 450 MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11, 451 MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12, 452 MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13, 453 MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14, 454 MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15, 455 MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16, 456 MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17, 457 MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18, 458 MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19, 459 MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20, 460 MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21, 461 MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22, 462 MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23, 463 }; 464 465 static void do_enable_hdmi(struct display_info_t const *dev) 466 { 467 imx_enable_hdmi_phy(); 468 } 469 470 static int detect_i2c(struct display_info_t const *dev) 471 { 472 return ((0 == i2c_set_bus_num(dev->bus)) 473 && 474 (0 == i2c_probe(dev->addr))); 475 } 476 477 static void enable_lvds(struct display_info_t const *dev) 478 { 479 struct iomuxc *iomux = (struct iomuxc *) 480 IOMUXC_BASE_ADDR; 481 u32 reg = readl(&iomux->gpr[2]); 482 reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT; 483 writel(reg, &iomux->gpr[2]); 484 gpio_direction_output(LVDS_BACKLIGHT_GP, 1); 485 } 486 487 static void enable_lvds_jeida(struct display_info_t const *dev) 488 { 489 struct iomuxc *iomux = (struct iomuxc *) 490 IOMUXC_BASE_ADDR; 491 u32 reg = readl(&iomux->gpr[2]); 492 reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT 493 |IOMUXC_GPR2_BIT_MAPPING_CH0_JEIDA; 494 writel(reg, &iomux->gpr[2]); 495 gpio_direction_output(LVDS_BACKLIGHT_GP, 1); 496 } 497 498 static void enable_rgb(struct display_info_t const *dev) 499 { 500 imx_iomux_v3_setup_multiple_pads( 501 rgb_pads, 502 ARRAY_SIZE(rgb_pads)); 503 gpio_direction_output(RGB_BACKLIGHT_GP, 1); 504 } 505 506 struct display_info_t const displays[] = {{ 507 .bus = 1, 508 .addr = 0x50, 509 .pixfmt = IPU_PIX_FMT_RGB24, 510 .detect = detect_i2c, 511 .enable = do_enable_hdmi, 512 .mode = { 513 .name = "HDMI", 514 .refresh = 60, 515 .xres = 1024, 516 .yres = 768, 517 .pixclock = 15385, 518 .left_margin = 220, 519 .right_margin = 40, 520 .upper_margin = 21, 521 .lower_margin = 7, 522 .hsync_len = 60, 523 .vsync_len = 10, 524 .sync = FB_SYNC_EXT, 525 .vmode = FB_VMODE_NONINTERLACED 526 } }, { 527 .bus = 0, 528 .addr = 0, 529 .pixfmt = IPU_PIX_FMT_RGB24, 530 .detect = NULL, 531 .enable = enable_lvds_jeida, 532 .mode = { 533 .name = "LDB-WXGA", 534 .refresh = 60, 535 .xres = 1280, 536 .yres = 800, 537 .pixclock = 14065, 538 .left_margin = 40, 539 .right_margin = 40, 540 .upper_margin = 3, 541 .lower_margin = 80, 542 .hsync_len = 10, 543 .vsync_len = 10, 544 .sync = FB_SYNC_EXT, 545 .vmode = FB_VMODE_NONINTERLACED 546 } }, { 547 .bus = 0, 548 .addr = 0, 549 .pixfmt = IPU_PIX_FMT_RGB24, 550 .detect = NULL, 551 .enable = enable_lvds, 552 .mode = { 553 .name = "LDB-WXGA-S", 554 .refresh = 60, 555 .xres = 1280, 556 .yres = 800, 557 .pixclock = 14065, 558 .left_margin = 40, 559 .right_margin = 40, 560 .upper_margin = 3, 561 .lower_margin = 80, 562 .hsync_len = 10, 563 .vsync_len = 10, 564 .sync = FB_SYNC_EXT, 565 .vmode = FB_VMODE_NONINTERLACED 566 } }, { 567 .bus = 2, 568 .addr = 0x4, 569 .pixfmt = IPU_PIX_FMT_LVDS666, 570 .detect = detect_i2c, 571 .enable = enable_lvds, 572 .mode = { 573 .name = "Hannstar-XGA", 574 .refresh = 60, 575 .xres = 1024, 576 .yres = 768, 577 .pixclock = 15385, 578 .left_margin = 220, 579 .right_margin = 40, 580 .upper_margin = 21, 581 .lower_margin = 7, 582 .hsync_len = 60, 583 .vsync_len = 10, 584 .sync = FB_SYNC_EXT, 585 .vmode = FB_VMODE_NONINTERLACED 586 } }, { 587 .bus = 0, 588 .addr = 0, 589 .pixfmt = IPU_PIX_FMT_LVDS666, 590 .detect = NULL, 591 .enable = enable_lvds, 592 .mode = { 593 .name = "LG-9.7", 594 .refresh = 60, 595 .xres = 1024, 596 .yres = 768, 597 .pixclock = 15385, /* ~65MHz */ 598 .left_margin = 480, 599 .right_margin = 260, 600 .upper_margin = 16, 601 .lower_margin = 6, 602 .hsync_len = 250, 603 .vsync_len = 10, 604 .sync = FB_SYNC_EXT, 605 .vmode = FB_VMODE_NONINTERLACED 606 } }, { 607 .bus = 2, 608 .addr = 0x38, 609 .pixfmt = IPU_PIX_FMT_LVDS666, 610 .detect = detect_i2c, 611 .enable = enable_lvds, 612 .mode = { 613 .name = "wsvga-lvds", 614 .refresh = 60, 615 .xres = 1024, 616 .yres = 600, 617 .pixclock = 15385, 618 .left_margin = 220, 619 .right_margin = 40, 620 .upper_margin = 21, 621 .lower_margin = 7, 622 .hsync_len = 60, 623 .vsync_len = 10, 624 .sync = FB_SYNC_EXT, 625 .vmode = FB_VMODE_NONINTERLACED 626 } }, { 627 .bus = 2, 628 .addr = 0x10, 629 .pixfmt = IPU_PIX_FMT_RGB666, 630 .detect = detect_i2c, 631 .enable = enable_rgb, 632 .mode = { 633 .name = "fusion7", 634 .refresh = 60, 635 .xres = 800, 636 .yres = 480, 637 .pixclock = 33898, 638 .left_margin = 96, 639 .right_margin = 24, 640 .upper_margin = 3, 641 .lower_margin = 10, 642 .hsync_len = 72, 643 .vsync_len = 7, 644 .sync = 0x40000002, 645 .vmode = FB_VMODE_NONINTERLACED 646 } }, { 647 .bus = 0, 648 .addr = 0, 649 .pixfmt = IPU_PIX_FMT_RGB666, 650 .detect = NULL, 651 .enable = enable_rgb, 652 .mode = { 653 .name = "svga", 654 .refresh = 60, 655 .xres = 800, 656 .yres = 600, 657 .pixclock = 15385, 658 .left_margin = 220, 659 .right_margin = 40, 660 .upper_margin = 21, 661 .lower_margin = 7, 662 .hsync_len = 60, 663 .vsync_len = 10, 664 .sync = 0, 665 .vmode = FB_VMODE_NONINTERLACED 666 } }, { 667 .bus = 2, 668 .addr = 0x41, 669 .pixfmt = IPU_PIX_FMT_LVDS666, 670 .detect = detect_i2c, 671 .enable = enable_lvds, 672 .mode = { 673 .name = "amp1024x600", 674 .refresh = 60, 675 .xres = 1024, 676 .yres = 600, 677 .pixclock = 15385, 678 .left_margin = 220, 679 .right_margin = 40, 680 .upper_margin = 21, 681 .lower_margin = 7, 682 .hsync_len = 60, 683 .vsync_len = 10, 684 .sync = FB_SYNC_EXT, 685 .vmode = FB_VMODE_NONINTERLACED 686 } }, { 687 .bus = 0, 688 .addr = 0, 689 .pixfmt = IPU_PIX_FMT_LVDS666, 690 .detect = 0, 691 .enable = enable_lvds, 692 .mode = { 693 .name = "wvga-lvds", 694 .refresh = 57, 695 .xres = 800, 696 .yres = 480, 697 .pixclock = 15385, 698 .left_margin = 220, 699 .right_margin = 40, 700 .upper_margin = 21, 701 .lower_margin = 7, 702 .hsync_len = 60, 703 .vsync_len = 10, 704 .sync = FB_SYNC_EXT, 705 .vmode = FB_VMODE_NONINTERLACED 706 } }, { 707 .bus = 2, 708 .addr = 0x48, 709 .pixfmt = IPU_PIX_FMT_RGB666, 710 .detect = detect_i2c, 711 .enable = enable_rgb, 712 .mode = { 713 .name = "wvga-rgb", 714 .refresh = 57, 715 .xres = 800, 716 .yres = 480, 717 .pixclock = 37037, 718 .left_margin = 40, 719 .right_margin = 60, 720 .upper_margin = 10, 721 .lower_margin = 10, 722 .hsync_len = 20, 723 .vsync_len = 10, 724 .sync = 0, 725 .vmode = FB_VMODE_NONINTERLACED 726 } }, { 727 .bus = 0, 728 .addr = 0, 729 .pixfmt = IPU_PIX_FMT_RGB24, 730 .detect = NULL, 731 .enable = enable_rgb, 732 .mode = { 733 .name = "qvga", 734 .refresh = 60, 735 .xres = 320, 736 .yres = 240, 737 .pixclock = 37037, 738 .left_margin = 38, 739 .right_margin = 37, 740 .upper_margin = 16, 741 .lower_margin = 15, 742 .hsync_len = 30, 743 .vsync_len = 3, 744 .sync = 0, 745 .vmode = FB_VMODE_NONINTERLACED 746 } } }; 747 size_t display_count = ARRAY_SIZE(displays); 748 749 int board_cfb_skip(void) 750 { 751 return NULL != env_get("novideo"); 752 } 753 754 static void setup_display(void) 755 { 756 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 757 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 758 int reg; 759 760 enable_ipu_clock(); 761 imx_setup_hdmi(); 762 /* Turn on LDB0,IPU,IPU DI0 clocks */ 763 reg = __raw_readl(&mxc_ccm->CCGR3); 764 reg |= MXC_CCM_CCGR3_LDB_DI0_MASK; 765 writel(reg, &mxc_ccm->CCGR3); 766 767 /* set LDB0, LDB1 clk select to 011/011 */ 768 reg = readl(&mxc_ccm->cs2cdr); 769 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK 770 |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 771 reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) 772 |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); 773 writel(reg, &mxc_ccm->cs2cdr); 774 775 reg = readl(&mxc_ccm->cscmr2); 776 reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; 777 writel(reg, &mxc_ccm->cscmr2); 778 779 reg = readl(&mxc_ccm->chsccdr); 780 reg |= (CHSCCDR_CLK_SEL_LDB_DI0 781 <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); 782 writel(reg, &mxc_ccm->chsccdr); 783 784 reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES 785 |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH 786 |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW 787 |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG 788 |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT 789 |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG 790 |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT 791 |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED 792 |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; 793 writel(reg, &iomux->gpr[2]); 794 795 reg = readl(&iomux->gpr[3]); 796 reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK 797 |IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) 798 | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 799 <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); 800 writel(reg, &iomux->gpr[3]); 801 802 /* backlights off until needed */ 803 imx_iomux_v3_setup_multiple_pads(backlight_pads, 804 ARRAY_SIZE(backlight_pads)); 805 gpio_direction_input(LVDS_BACKLIGHT_GP); 806 gpio_direction_input(RGB_BACKLIGHT_GP); 807 } 808 #endif 809 810 static iomux_v3_cfg_t const init_pads[] = { 811 /* SGTL5000 sys_mclk */ 812 NEW_PAD_CTRL(MX6_PAD_GPIO_0__CCM_CLKO1, OUTPUT_40OHM), 813 814 /* J5 - Camera MCLK */ 815 NEW_PAD_CTRL(MX6_PAD_GPIO_3__CCM_CLKO2, OUTPUT_40OHM), 816 817 /* wl1271 pads on nitrogen6x */ 818 /* WL12XX_WL_IRQ_GP */ 819 NEW_PAD_CTRL(MX6_PAD_NANDF_CS1__GPIO6_IO14, WEAK_PULLDOWN), 820 /* WL12XX_WL_ENABLE_GP */ 821 NEW_PAD_CTRL(MX6_PAD_NANDF_CS2__GPIO6_IO15, OUTPUT_40OHM), 822 /* WL12XX_BT_ENABLE_GP */ 823 NEW_PAD_CTRL(MX6_PAD_NANDF_CS3__GPIO6_IO16, OUTPUT_40OHM), 824 /* USB otg power */ 825 NEW_PAD_CTRL(MX6_PAD_EIM_D22__GPIO3_IO22, OUTPUT_40OHM), 826 NEW_PAD_CTRL(MX6_PAD_NANDF_D5__GPIO2_IO05, OUTPUT_40OHM), 827 NEW_PAD_CTRL(MX6_PAD_NANDF_WP_B__GPIO6_IO09, OUTPUT_40OHM), 828 NEW_PAD_CTRL(MX6_PAD_GPIO_8__GPIO1_IO08, OUTPUT_40OHM), 829 NEW_PAD_CTRL(MX6_PAD_GPIO_6__GPIO1_IO06, OUTPUT_40OHM), 830 }; 831 832 #define WL12XX_WL_IRQ_GP IMX_GPIO_NR(6, 14) 833 834 static unsigned gpios_out_low[] = { 835 /* Disable wl1271 */ 836 IMX_GPIO_NR(6, 15), /* disable wireless */ 837 IMX_GPIO_NR(6, 16), /* disable bluetooth */ 838 IMX_GPIO_NR(3, 22), /* disable USB otg power */ 839 IMX_GPIO_NR(2, 5), /* ov5640 mipi camera reset */ 840 IMX_GPIO_NR(1, 8), /* ov5642 reset */ 841 }; 842 843 static unsigned gpios_out_high[] = { 844 IMX_GPIO_NR(1, 6), /* ov5642 powerdown */ 845 IMX_GPIO_NR(6, 9), /* ov5640 mipi camera power down */ 846 }; 847 848 static void set_gpios(unsigned *p, int cnt, int val) 849 { 850 int i; 851 852 for (i = 0; i < cnt; i++) 853 gpio_direction_output(*p++, val); 854 } 855 856 int board_early_init_f(void) 857 { 858 setup_iomux_uart(); 859 860 set_gpios(gpios_out_high, ARRAY_SIZE(gpios_out_high), 1); 861 set_gpios(gpios_out_low, ARRAY_SIZE(gpios_out_low), 0); 862 gpio_direction_input(WL12XX_WL_IRQ_GP); 863 864 imx_iomux_v3_setup_multiple_pads(wl12xx_pads, ARRAY_SIZE(wl12xx_pads)); 865 imx_iomux_v3_setup_multiple_pads(init_pads, ARRAY_SIZE(init_pads)); 866 setup_buttons(); 867 868 #if defined(CONFIG_VIDEO_IPUV3) 869 setup_display(); 870 #endif 871 return 0; 872 } 873 874 /* 875 * Do not overwrite the console 876 * Use always serial for U-Boot console 877 */ 878 int overwrite_console(void) 879 { 880 return 1; 881 } 882 883 int board_init(void) 884 { 885 struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 886 887 clrsetbits_le32(&iomuxc_regs->gpr[1], 888 IOMUXC_GPR1_OTG_ID_MASK, 889 IOMUXC_GPR1_OTG_ID_GPIO1); 890 891 imx_iomux_v3_setup_multiple_pads(misc_pads, ARRAY_SIZE(misc_pads)); 892 893 /* address of boot parameters */ 894 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; 895 896 #ifdef CONFIG_MXC_SPI 897 setup_spi(); 898 #endif 899 imx_iomux_v3_setup_multiple_pads( 900 usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); 901 setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0); 902 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); 903 setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); 904 905 #ifdef CONFIG_SATA 906 setup_sata(); 907 #endif 908 909 return 0; 910 } 911 912 int checkboard(void) 913 { 914 if (gpio_get_value(WL12XX_WL_IRQ_GP)) 915 puts("Board: Nitrogen6X\n"); 916 else 917 puts("Board: SABRE Lite\n"); 918 919 return 0; 920 } 921 922 struct button_key { 923 char const *name; 924 unsigned gpnum; 925 char ident; 926 }; 927 928 static struct button_key const buttons[] = { 929 {"back", IMX_GPIO_NR(2, 2), 'B'}, 930 {"home", IMX_GPIO_NR(2, 4), 'H'}, 931 {"menu", IMX_GPIO_NR(2, 1), 'M'}, 932 {"search", IMX_GPIO_NR(2, 3), 'S'}, 933 {"volup", IMX_GPIO_NR(7, 13), 'V'}, 934 {"voldown", IMX_GPIO_NR(4, 5), 'v'}, 935 }; 936 937 /* 938 * generate a null-terminated string containing the buttons pressed 939 * returns number of keys pressed 940 */ 941 static int read_keys(char *buf) 942 { 943 int i, numpressed = 0; 944 for (i = 0; i < ARRAY_SIZE(buttons); i++) { 945 if (!gpio_get_value(buttons[i].gpnum)) 946 buf[numpressed++] = buttons[i].ident; 947 } 948 buf[numpressed] = '\0'; 949 return numpressed; 950 } 951 952 static int do_kbd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) 953 { 954 char envvalue[ARRAY_SIZE(buttons)+1]; 955 int numpressed = read_keys(envvalue); 956 env_set("keybd", envvalue); 957 return numpressed == 0; 958 } 959 960 U_BOOT_CMD( 961 kbd, 1, 1, do_kbd, 962 "Tests for keypresses, sets 'keybd' environment variable", 963 "Returns 0 (true) to shell if key is pressed." 964 ); 965 966 #ifdef CONFIG_PREBOOT 967 static char const kbd_magic_prefix[] = "key_magic"; 968 static char const kbd_command_prefix[] = "key_cmd"; 969 970 static void preboot_keys(void) 971 { 972 int numpressed; 973 char keypress[ARRAY_SIZE(buttons)+1]; 974 numpressed = read_keys(keypress); 975 if (numpressed) { 976 char *kbd_magic_keys = env_get("magic_keys"); 977 char *suffix; 978 /* 979 * loop over all magic keys 980 */ 981 for (suffix = kbd_magic_keys; *suffix; ++suffix) { 982 char *keys; 983 char magic[sizeof(kbd_magic_prefix) + 1]; 984 sprintf(magic, "%s%c", kbd_magic_prefix, *suffix); 985 keys = env_get(magic); 986 if (keys) { 987 if (!strcmp(keys, keypress)) 988 break; 989 } 990 } 991 if (*suffix) { 992 char cmd_name[sizeof(kbd_command_prefix) + 1]; 993 char *cmd; 994 sprintf(cmd_name, "%s%c", kbd_command_prefix, *suffix); 995 cmd = env_get(cmd_name); 996 if (cmd) { 997 env_set("preboot", cmd); 998 return; 999 } 1000 } 1001 } 1002 } 1003 #endif 1004 1005 #ifdef CONFIG_CMD_BMODE 1006 static const struct boot_mode board_boot_modes[] = { 1007 /* 4 bit bus width */ 1008 {"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, 1009 {"mmc1", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, 1010 {NULL, 0}, 1011 }; 1012 #endif 1013 1014 int misc_init_r(void) 1015 { 1016 #ifdef CONFIG_PREBOOT 1017 preboot_keys(); 1018 #endif 1019 1020 #ifdef CONFIG_CMD_BMODE 1021 add_board_boot_modes(board_boot_modes); 1022 #endif 1023 env_set_hex("reset_cause", get_imx_reset_cause()); 1024 return 0; 1025 } 1026