1 /* 2 * board.c 3 * 4 * Board functions for Birdland Audio BAV335x Network Processor 5 * 6 * Copyright (c) 2012-2014 Birdland Audio - http://birdland.com/oem 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <errno.h> 13 #include <spl.h> 14 #include <asm/arch/cpu.h> 15 #include <asm/arch/hardware.h> 16 #include <asm/arch/omap.h> 17 #include <asm/arch/ddr_defs.h> 18 #include <asm/arch/clock.h> 19 #include <asm/arch/gpio.h> 20 #include <asm/arch/mmc_host_def.h> 21 #include <asm/arch/sys_proto.h> 22 #include <asm/arch/mem.h> 23 #include <asm/io.h> 24 #include <asm/emif.h> 25 #include <asm/gpio.h> 26 #include <i2c.h> 27 #include <miiphy.h> 28 #include <cpsw.h> 29 #include <power/tps65217.h> 30 #include <power/tps65910.h> 31 #include <environment.h> 32 #include <watchdog.h> 33 #include <environment.h> 34 #include "board.h" 35 36 DECLARE_GLOBAL_DATA_PTR; 37 38 /* GPIO that controls power to DDR on EVM-SK */ 39 #define GPIO_DDR_VTT_EN 7 40 41 static __maybe_unused struct ctrl_dev *cdev = 42 (struct ctrl_dev *)CTRL_DEVICE_BASE; 43 44 45 46 /* 47 * Read header information from EEPROM into global structure. 48 */ 49 static int read_eeprom(struct board_eeconfig *header) 50 { 51 /* Check if baseboard eeprom is available */ 52 if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) 53 return -ENODEV; 54 55 /* read the eeprom using i2c */ 56 if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header, 57 sizeof(struct board_eeconfig))) 58 return -EIO; 59 60 if (header->magic != BOARD_MAGIC) { 61 /* read the i2c eeprom again using only a 1 byte address */ 62 if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header, 63 sizeof(struct board_eeconfig))) 64 return -EIO; 65 66 if (header->magic != BOARD_MAGIC) 67 return -EINVAL; 68 } 69 return 0; 70 } 71 72 73 74 75 enum board_type get_board_type(bool debug) 76 { 77 int ecode; 78 struct board_eeconfig header; 79 80 ecode = read_eeprom(&header); 81 if (ecode == 0) { 82 if (header.version[1] == 'A') { 83 if (debug) 84 puts("=== Detected Board model BAV335x Rev.A"); 85 return BAV335A; 86 } else if (header.version[1] == 'B') { 87 if (debug) 88 puts("=== Detected Board model BAV335x Rev.B"); 89 return BAV335B; 90 } else if (debug) { 91 puts("### Un-known board model in serial-EE\n"); 92 } 93 } else if (debug) { 94 switch (ecode) { 95 case -ENODEV: 96 puts("### Board doesn't have a serial-EE\n"); 97 break; 98 case -EINVAL: 99 puts("### Board serial-EE signature is incorrect.\n"); 100 break; 101 default: 102 puts("### IO Error reading serial-EE.\n"); 103 break; 104 } 105 } 106 107 #if (CONFIG_BAV_VERSION == 1) 108 if (debug) 109 puts("### Selecting BAV335A as per config\n"); 110 return BAV335A; 111 #elif (CONFIG_BAV_VERSION == 2) 112 if (debug) 113 puts("### Selecting BAV335B as per config\n"); 114 return BAV335B; 115 #endif 116 #if (NOT_DEFINED == 2) 117 #error "SHOULD NEVER DISPLAY THIS" 118 #endif 119 120 if (debug) 121 puts("### Defaulting to model BAV335x Rev.B\n"); 122 return BAV335B; 123 } 124 125 126 127 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 128 static const struct ddr_data ddr3_bav335x_data = { 129 .datardsratio0 = MT41K256M16HA125E_RD_DQS, 130 .datawdsratio0 = MT41K256M16HA125E_WR_DQS, 131 .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE, 132 .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA, 133 }; 134 135 static const struct cmd_control ddr3_bav335x_cmd_ctrl_data = { 136 .cmd0csratio = MT41K256M16HA125E_RATIO, 137 .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 138 .cmd1csratio = MT41K256M16HA125E_RATIO, 139 .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 140 .cmd2csratio = MT41K256M16HA125E_RATIO, 141 .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT, 142 }; 143 144 145 static struct emif_regs ddr3_bav335x_emif_reg_data = { 146 .sdram_config = MT41K256M16HA125E_EMIF_SDCFG, 147 .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF, 148 .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1, 149 .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2, 150 .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3, 151 .zq_config = MT41K256M16HA125E_ZQ_CFG, 152 .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY, 153 }; 154 155 156 #ifdef CONFIG_SPL_OS_BOOT 157 int spl_start_uboot(void) 158 { 159 /* break into full u-boot on 'c' */ 160 if (serial_tstc() && serial_getc() == 'c') 161 return 1; 162 163 #ifdef CONFIG_SPL_ENV_SUPPORT 164 env_init(); 165 env_relocate_spec(); 166 if (getenv_yesno("boot_os") != 1) 167 return 1; 168 #endif 169 170 return 0; 171 } 172 #endif 173 174 #define OSC (V_OSCK/1000000) 175 const struct dpll_params dpll_ddr = { 176 266, OSC-1, 1, -1, -1, -1, -1}; 177 const struct dpll_params dpll_ddr_evm_sk = { 178 303, OSC-1, 1, -1, -1, -1, -1}; 179 const struct dpll_params dpll_ddr_bone_black = { 180 400, OSC-1, 1, -1, -1, -1, -1}; 181 182 void am33xx_spl_board_init(void) 183 { 184 /* debug print detect status */ 185 (void)get_board_type(true); 186 187 /* Get the frequency */ 188 /* dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); */ 189 dpll_mpu_opp100.m = MPUPLL_M_1000; 190 191 if (i2c_probe(TPS65217_CHIP_PM)) 192 return; 193 194 /* Set the USB Current Limit */ 195 if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH, 196 TPS65217_USB_INPUT_CUR_LIMIT_1800MA, 197 TPS65217_USB_INPUT_CUR_LIMIT_MASK)) 198 puts("! tps65217_reg_write: could not set USB limit\n"); 199 200 /* Set the Core Voltage (DCDC3) to 1.125V */ 201 if (tps65217_voltage_update(TPS65217_DEFDCDC3, 202 TPS65217_DCDC_VOLT_SEL_1125MV)) { 203 puts("! tps65217_reg_write: could not set Core Voltage\n"); 204 return; 205 } 206 207 /* Set CORE Frequencies to OPP100 */ 208 do_setup_dpll(&dpll_core_regs, &dpll_core_opp100); 209 210 /* Set the MPU Voltage (DCDC2) */ 211 if (tps65217_voltage_update(TPS65217_DEFDCDC2, 212 TPS65217_DCDC_VOLT_SEL_1325MV)) { 213 puts("! tps65217_reg_write: could not set MPU Voltage\n"); 214 return; 215 } 216 217 /* 218 * Set LDO3, LDO4 output voltage to 3.3V for Beaglebone. 219 * Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black. 220 */ 221 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS1, 222 TPS65217_LDO_VOLTAGE_OUT_1_8, TPS65217_LDO_MASK)) 223 puts("! tps65217_reg_write: could not set LDO3\n"); 224 225 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS2, 226 TPS65217_LDO_VOLTAGE_OUT_3_3, TPS65217_LDO_MASK)) 227 puts("! tps65217_reg_write: could not set LDO4\n"); 228 229 /* Set MPU Frequency to what we detected now that voltages are set */ 230 do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100); 231 } 232 233 const struct dpll_params *get_dpll_ddr_params(void) 234 { 235 enable_i2c0_pin_mux(); 236 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); 237 238 return &dpll_ddr_bone_black; 239 } 240 241 void set_uart_mux_conf(void) 242 { 243 #if CONFIG_CONS_INDEX == 1 244 enable_uart0_pin_mux(); 245 #elif CONFIG_CONS_INDEX == 2 246 enable_uart1_pin_mux(); 247 #elif CONFIG_CONS_INDEX == 3 248 enable_uart2_pin_mux(); 249 #elif CONFIG_CONS_INDEX == 4 250 enable_uart3_pin_mux(); 251 #elif CONFIG_CONS_INDEX == 5 252 enable_uart4_pin_mux(); 253 #elif CONFIG_CONS_INDEX == 6 254 enable_uart5_pin_mux(); 255 #endif 256 } 257 258 void set_mux_conf_regs(void) 259 { 260 enum board_type board; 261 262 board = get_board_type(false); 263 enable_board_pin_mux(board); 264 } 265 266 const struct ctrl_ioregs ioregs_bonelt = { 267 .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 268 .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 269 .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 270 .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 271 .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, 272 }; 273 274 275 void sdram_init(void) 276 { 277 config_ddr(400, &ioregs_bonelt, 278 &ddr3_bav335x_data, 279 &ddr3_bav335x_cmd_ctrl_data, 280 &ddr3_bav335x_emif_reg_data, 0); 281 } 282 #endif 283 284 /* 285 * Basic board specific setup. Pinmux has been handled already. 286 */ 287 int board_init(void) 288 { 289 #if defined(CONFIG_HW_WATCHDOG) 290 hw_watchdog_init(); 291 #endif 292 293 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 294 #if defined(CONFIG_NOR) || defined(CONFIG_NAND) 295 gpmc_init(); 296 #endif 297 return 0; 298 } 299 300 #ifdef CONFIG_BOARD_LATE_INIT 301 int board_late_init(void) 302 { 303 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 304 setenv("board_name", "BAV335xB"); 305 setenv("board_rev", "B"); /* Fix me, but why bother.. */ 306 #endif 307 return 0; 308 } 309 #endif 310 311 312 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 313 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 314 static void cpsw_control(int enabled) 315 { 316 /* VTP can be added here */ 317 return; 318 } 319 320 static struct cpsw_slave_data cpsw_slaves[] = { 321 { 322 .slave_reg_ofs = 0x208, 323 .sliver_reg_ofs = 0xd80, 324 .phy_addr = 0, 325 }, 326 { 327 .slave_reg_ofs = 0x308, 328 .sliver_reg_ofs = 0xdc0, 329 .phy_addr = 1, 330 }, 331 }; 332 333 static struct cpsw_platform_data cpsw_data = { 334 .mdio_base = CPSW_MDIO_BASE, 335 .cpsw_base = CPSW_BASE, 336 .mdio_div = 0xff, 337 .channels = 8, 338 .cpdma_reg_ofs = 0x800, 339 .slaves = 1, 340 .slave_data = cpsw_slaves, 341 .ale_reg_ofs = 0xd00, 342 .ale_entries = 1024, 343 .host_port_reg_ofs = 0x108, 344 .hw_stats_reg_ofs = 0x900, 345 .bd_ram_ofs = 0x2000, 346 .mac_control = (1 << 5), 347 .control = cpsw_control, 348 .host_port_num = 0, 349 .version = CPSW_CTRL_VERSION_2, 350 }; 351 #endif 352 353 354 /* 355 * This function will: 356 * Perform fixups to the PHY present on certain boards. We only need this 357 * function in: 358 * - SPL with either CPSW or USB ethernet support 359 * - Full U-Boot, with either CPSW or USB ethernet 360 * Build in only these cases to avoid warnings about unused variables 361 * when we build an SPL that has neither option but full U-Boot will. 362 */ 363 #if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) &&\ 364 defined(CONFIG_SPL_BUILD)) || \ 365 ((defined(CONFIG_DRIVER_TI_CPSW) || \ 366 defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \ 367 !defined(CONFIG_SPL_BUILD)) 368 int board_eth_init(bd_t *bis) 369 { 370 int ecode, rv, n; 371 uint8_t mac_addr[6]; 372 struct board_eeconfig header; 373 __maybe_unused enum board_type board; 374 375 /* Default manufacturing address; used when no EE or invalid */ 376 n = 0; 377 mac_addr[0] = 0; 378 mac_addr[1] = 0x20; 379 mac_addr[2] = 0x18; 380 mac_addr[3] = 0x1C; 381 mac_addr[4] = 0x00; 382 mac_addr[5] = 0x01; 383 384 ecode = read_eeprom(&header); 385 /* if we have a valid EE, get mac address from there */ 386 if ((ecode == 0) && 387 is_valid_ethaddr((const u8 *)&header.mac_addr[0][0])) { 388 memcpy(mac_addr, (const void *)&header.mac_addr[0][0], 6); 389 } 390 391 392 #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ 393 (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) 394 395 if (!getenv("ethaddr")) { 396 printf("<ethaddr> not set. Validating first E-fuse MAC\n"); 397 398 if (is_valid_ethaddr(mac_addr)) 399 eth_setenv_enetaddr("ethaddr", mac_addr); 400 } 401 402 #ifdef CONFIG_DRIVER_TI_CPSW 403 404 board = get_board_type(false); 405 406 /* Rev.A uses 10/100 PHY in mii mode */ 407 if (board == BAV335A) { 408 writel(MII_MODE_ENABLE, &cdev->miisel); 409 cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII; 410 cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII; 411 } 412 /* Rev.B (default) uses GB PHY in rmii mode */ 413 else { 414 writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel); 415 cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if 416 = PHY_INTERFACE_MODE_RGMII; 417 } 418 419 rv = cpsw_register(&cpsw_data); 420 if (rv < 0) 421 printf("Error %d registering CPSW switch\n", rv); 422 else 423 n += rv; 424 #endif 425 426 #endif 427 428 return n; 429 } 430 #endif 431