1 /* 2 * Copyright (C) 2014 Atmel 3 * Bo Shen <voice.shen@atmel.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #include <common.h> 9 #include <asm/io.h> 10 #include <asm/arch/at91_common.h> 11 #include <asm/arch/at91_pmc.h> 12 #include <asm/arch/at91_rstc.h> 13 #include <asm/arch/atmel_mpddrc.h> 14 #include <asm/arch/atmel_usba_udc.h> 15 #include <asm/arch/gpio.h> 16 #include <asm/arch/clk.h> 17 #include <asm/arch/sama5d3_smc.h> 18 #include <asm/arch/sama5d4.h> 19 #include <atmel_hlcdc.h> 20 #include <atmel_mci.h> 21 #include <lcd.h> 22 #include <mmc.h> 23 #include <net.h> 24 #include <netdev.h> 25 #include <nand.h> 26 #include <spi.h> 27 28 DECLARE_GLOBAL_DATA_PTR; 29 30 #ifdef CONFIG_ATMEL_SPI 31 int spi_cs_is_valid(unsigned int bus, unsigned int cs) 32 { 33 return bus == 0 && cs == 0; 34 } 35 36 void spi_cs_activate(struct spi_slave *slave) 37 { 38 at91_set_pio_output(AT91_PIO_PORTC, 3, 0); 39 } 40 41 void spi_cs_deactivate(struct spi_slave *slave) 42 { 43 at91_set_pio_output(AT91_PIO_PORTC, 3, 1); 44 } 45 46 static void sama5d4ek_spi0_hw_init(void) 47 { 48 at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */ 49 at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */ 50 at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */ 51 52 at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */ 53 54 /* Enable clock */ 55 at91_periph_clk_enable(ATMEL_ID_SPI0); 56 } 57 #endif /* CONFIG_ATMEL_SPI */ 58 59 #ifdef CONFIG_NAND_ATMEL 60 static void sama5d4ek_nand_hw_init(void) 61 { 62 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; 63 64 at91_periph_clk_enable(ATMEL_ID_SMC); 65 66 /* Configure SMC CS3 for NAND */ 67 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) | 68 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1), 69 &smc->cs[3].setup); 70 writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) | 71 AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3), 72 &smc->cs[3].pulse); 73 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), 74 &smc->cs[3].cycle); 75 writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) | 76 AT91_SMC_TIMINGS_TAR(2) | AT91_SMC_TIMINGS_TRR(3) | 77 AT91_SMC_TIMINGS_TWB(7) | AT91_SMC_TIMINGS_RBNSEL(3)| 78 AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings); 79 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 80 AT91_SMC_MODE_EXNW_DISABLE | 81 AT91_SMC_MODE_DBW_8 | 82 AT91_SMC_MODE_TDF_CYCLE(3), 83 &smc->cs[3].mode); 84 85 at91_set_a_periph(AT91_PIO_PORTC, 5, 0); /* D0 */ 86 at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* D1 */ 87 at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* D2 */ 88 at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* D3 */ 89 at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* D4 */ 90 at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* D5 */ 91 at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* D6 */ 92 at91_set_a_periph(AT91_PIO_PORTC, 12, 0); /* D7 */ 93 at91_set_a_periph(AT91_PIO_PORTC, 13, 0); /* RE */ 94 at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* WE */ 95 at91_set_a_periph(AT91_PIO_PORTC, 15, 1); /* NCS */ 96 at91_set_a_periph(AT91_PIO_PORTC, 16, 1); /* RDY */ 97 at91_set_a_periph(AT91_PIO_PORTC, 17, 1); /* ALE */ 98 at91_set_a_periph(AT91_PIO_PORTC, 18, 1); /* CLE */ 99 } 100 #endif 101 102 #ifdef CONFIG_CMD_USB 103 static void sama5d4ek_usb_hw_init(void) 104 { 105 at91_set_pio_output(AT91_PIO_PORTE, 11, 0); 106 at91_set_pio_output(AT91_PIO_PORTE, 12, 0); 107 at91_set_pio_output(AT91_PIO_PORTE, 10, 0); 108 } 109 #endif 110 111 #ifdef CONFIG_LCD 112 vidinfo_t panel_info = { 113 .vl_col = 800, 114 .vl_row = 480, 115 .vl_clk = 33260000, 116 .vl_bpix = LCD_BPP, 117 .vl_tft = 1, 118 .vl_hsync_len = 5, 119 .vl_left_margin = 128, 120 .vl_right_margin = 0, 121 .vl_vsync_len = 5, 122 .vl_upper_margin = 23, 123 .vl_lower_margin = 22, 124 .mmio = ATMEL_BASE_LCDC, 125 }; 126 127 /* No power up/down pin for the LCD pannel */ 128 void lcd_enable(void) { /* Empty! */ } 129 void lcd_disable(void) { /* Empty! */ } 130 131 unsigned int has_lcdc(void) 132 { 133 return 1; 134 } 135 136 static void sama5d4ek_lcd_hw_init(void) 137 { 138 at91_set_a_periph(AT91_PIO_PORTA, 24, 0); /* LCDPWM */ 139 at91_set_a_periph(AT91_PIO_PORTA, 25, 0); /* LCDDISP */ 140 at91_set_a_periph(AT91_PIO_PORTA, 26, 0); /* LCDVSYNC */ 141 at91_set_a_periph(AT91_PIO_PORTA, 27, 0); /* LCDHSYNC */ 142 at91_set_a_periph(AT91_PIO_PORTA, 28, 0); /* LCDDOTCK */ 143 at91_set_a_periph(AT91_PIO_PORTA, 29, 0); /* LCDDEN */ 144 145 at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* LCDD2 */ 146 at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* LCDD3 */ 147 at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* LCDD4 */ 148 at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* LCDD5 */ 149 at91_set_a_periph(AT91_PIO_PORTA, 6, 0); /* LCDD6 */ 150 at91_set_a_periph(AT91_PIO_PORTA, 7, 0); /* LCDD7 */ 151 152 at91_set_a_periph(AT91_PIO_PORTA, 10, 0); /* LCDD10 */ 153 at91_set_a_periph(AT91_PIO_PORTA, 11, 0); /* LCDD11 */ 154 at91_set_a_periph(AT91_PIO_PORTA, 12, 0); /* LCDD12 */ 155 at91_set_a_periph(AT91_PIO_PORTA, 13, 0); /* LCDD13 */ 156 at91_set_a_periph(AT91_PIO_PORTA, 14, 0); /* LCDD14 */ 157 at91_set_a_periph(AT91_PIO_PORTA, 15, 0); /* LCDD15 */ 158 159 at91_set_a_periph(AT91_PIO_PORTA, 18, 0); /* LCDD18 */ 160 at91_set_a_periph(AT91_PIO_PORTA, 19, 0); /* LCDD19 */ 161 at91_set_a_periph(AT91_PIO_PORTA, 20, 0); /* LCDD20 */ 162 at91_set_a_periph(AT91_PIO_PORTA, 21, 0); /* LCDD21 */ 163 at91_set_a_periph(AT91_PIO_PORTA, 22, 0); /* LCDD22 */ 164 at91_set_a_periph(AT91_PIO_PORTA, 23, 0); /* LCDD23 */ 165 166 /* Enable clock */ 167 at91_periph_clk_enable(ATMEL_ID_LCDC); 168 } 169 170 #ifdef CONFIG_LCD_INFO 171 void lcd_show_board_info(void) 172 { 173 ulong dram_size, nand_size; 174 int i; 175 char temp[32]; 176 177 lcd_printf("2014 ATMEL Corp\n"); 178 lcd_printf("at91@atmel.com\n"); 179 lcd_printf("%s CPU at %s MHz\n", get_cpu_name(), 180 strmhz(temp, get_cpu_clk_rate())); 181 182 dram_size = 0; 183 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) 184 dram_size += gd->bd->bi_dram[i].size; 185 186 nand_size = 0; 187 #ifdef CONFIG_NAND_ATMEL 188 for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) 189 nand_size += nand_info[i].size; 190 #endif 191 lcd_printf("%ld MB SDRAM, %ld MB NAND\n", 192 dram_size >> 20, nand_size >> 20); 193 } 194 #endif /* CONFIG_LCD_INFO */ 195 196 #endif /* CONFIG_LCD */ 197 198 #ifdef CONFIG_GENERIC_ATMEL_MCI 199 void sama5d4ek_mci1_hw_init(void) 200 { 201 at91_set_c_periph(AT91_PIO_PORTE, 19, 1); /* MCI1 CDA */ 202 at91_set_c_periph(AT91_PIO_PORTE, 20, 1); /* MCI1 DA0 */ 203 at91_set_c_periph(AT91_PIO_PORTE, 21, 1); /* MCI1 DA1 */ 204 at91_set_c_periph(AT91_PIO_PORTE, 22, 1); /* MCI1 DA2 */ 205 at91_set_c_periph(AT91_PIO_PORTE, 23, 1); /* MCI1 DA3 */ 206 at91_set_c_periph(AT91_PIO_PORTE, 18, 0); /* MCI1 CLK */ 207 208 /* 209 * As the mci io internal pull down is too strong, so if the io needs 210 * external pull up, the pull up resistor will be very small, if so 211 * the power consumption will increase, so disable the interanl pull 212 * down to save the power. 213 */ 214 at91_set_pio_pulldown(AT91_PIO_PORTE, 18, 0); 215 at91_set_pio_pulldown(AT91_PIO_PORTE, 19, 0); 216 at91_set_pio_pulldown(AT91_PIO_PORTE, 20, 0); 217 at91_set_pio_pulldown(AT91_PIO_PORTE, 21, 0); 218 at91_set_pio_pulldown(AT91_PIO_PORTE, 22, 0); 219 at91_set_pio_pulldown(AT91_PIO_PORTE, 23, 0); 220 221 /* Enable clock */ 222 at91_periph_clk_enable(ATMEL_ID_MCI1); 223 } 224 225 int board_mmc_init(bd_t *bis) 226 { 227 /* Enable power for MCI1 interface */ 228 at91_set_pio_output(AT91_PIO_PORTE, 15, 0); 229 230 return atmel_mci_init((void *)ATMEL_BASE_MCI1); 231 } 232 #endif /* CONFIG_GENERIC_ATMEL_MCI */ 233 234 #ifdef CONFIG_MACB 235 void sama5d4ek_macb0_hw_init(void) 236 { 237 at91_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ETXCK_EREFCK */ 238 at91_set_a_periph(AT91_PIO_PORTB, 6, 0); /* ERXDV */ 239 at91_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ERX0 */ 240 at91_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ERX1 */ 241 at91_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ERXER */ 242 at91_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ETXEN */ 243 at91_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX0 */ 244 at91_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ETX1 */ 245 at91_set_a_periph(AT91_PIO_PORTB, 17, 0); /* EMDIO */ 246 at91_set_a_periph(AT91_PIO_PORTB, 16, 0); /* EMDC */ 247 248 /* Enable clock */ 249 at91_periph_clk_enable(ATMEL_ID_GMAC0); 250 } 251 #endif 252 253 static void sama5d4ek_serial3_hw_init(void) 254 { 255 at91_set_b_periph(AT91_PIO_PORTE, 17, 1); /* TXD3 */ 256 at91_set_b_periph(AT91_PIO_PORTE, 16, 0); /* RXD3 */ 257 258 /* Enable clock */ 259 at91_periph_clk_enable(ATMEL_ID_USART3); 260 } 261 262 int board_early_init_f(void) 263 { 264 at91_periph_clk_enable(ATMEL_ID_PIOA); 265 at91_periph_clk_enable(ATMEL_ID_PIOB); 266 at91_periph_clk_enable(ATMEL_ID_PIOC); 267 at91_periph_clk_enable(ATMEL_ID_PIOD); 268 at91_periph_clk_enable(ATMEL_ID_PIOE); 269 270 sama5d4ek_serial3_hw_init(); 271 272 return 0; 273 } 274 275 int board_init(void) 276 { 277 /* adress of boot parameters */ 278 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 279 280 #ifdef CONFIG_ATMEL_SPI 281 sama5d4ek_spi0_hw_init(); 282 #endif 283 #ifdef CONFIG_NAND_ATMEL 284 sama5d4ek_nand_hw_init(); 285 #endif 286 #ifdef CONFIG_GENERIC_ATMEL_MCI 287 sama5d4ek_mci1_hw_init(); 288 #endif 289 #ifdef CONFIG_MACB 290 sama5d4ek_macb0_hw_init(); 291 #endif 292 #ifdef CONFIG_LCD 293 sama5d4ek_lcd_hw_init(); 294 #endif 295 #ifdef CONFIG_CMD_USB 296 sama5d4ek_usb_hw_init(); 297 #endif 298 #ifdef CONFIG_USB_GADGET_ATMEL_USBA 299 at91_udp_hw_init(); 300 #endif 301 302 return 0; 303 } 304 305 int dram_init(void) 306 { 307 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 308 CONFIG_SYS_SDRAM_SIZE); 309 return 0; 310 } 311 312 int board_eth_init(bd_t *bis) 313 { 314 int rc = 0; 315 316 #ifdef CONFIG_MACB 317 rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00); 318 #endif 319 320 #ifdef CONFIG_USB_GADGET_ATMEL_USBA 321 usba_udc_probe(&pdata); 322 #ifdef CONFIG_USB_ETH_RNDIS 323 usb_eth_initialize(bis); 324 #endif 325 #endif 326 327 return rc; 328 } 329 330 /* SPL */ 331 #ifdef CONFIG_SPL_BUILD 332 void spl_board_init(void) 333 { 334 #ifdef CONFIG_SYS_USE_MMC 335 sama5d4ek_mci1_hw_init(); 336 #elif CONFIG_SYS_USE_NANDFLASH 337 sama5d4ek_nand_hw_init(); 338 #elif CONFIG_SYS_USE_SERIALFLASH 339 sama5d4ek_spi0_hw_init(); 340 #endif 341 } 342 343 static void ddr2_conf(struct atmel_mpddr *ddr2) 344 { 345 ddr2->md = (ATMEL_MPDDRC_MD_DBW_32_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM); 346 347 ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 | 348 ATMEL_MPDDRC_CR_NR_ROW_14 | 349 ATMEL_MPDDRC_CR_CAS_DDR_CAS3 | 350 ATMEL_MPDDRC_CR_NB_8BANKS | 351 ATMEL_MPDDRC_CR_NDQS_DISABLED | 352 ATMEL_MPDDRC_CR_DECOD_INTERLEAVED | 353 ATMEL_MPDDRC_CR_UNAL_SUPPORTED); 354 355 ddr2->rtr = 0x2b0; 356 357 ddr2->tpr0 = (8 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET | 358 3 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET | 359 3 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | 360 10 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | 361 3 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | 362 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | 363 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | 364 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); 365 366 ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | 367 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET | 368 25 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET | 369 23 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET); 370 371 ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET | 372 2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET | 373 3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET | 374 2 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET | 375 8 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET); 376 } 377 378 void mem_init(void) 379 { 380 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 381 struct atmel_mpddr ddr2; 382 383 ddr2_conf(&ddr2); 384 385 /* enable MPDDR clock */ 386 at91_periph_clk_enable(ATMEL_ID_MPDDRC); 387 writel(0x4, &pmc->scer); 388 389 /* DDRAM2 Controller initialize */ 390 ddr2_init(ATMEL_BASE_DDRCS, &ddr2); 391 } 392 393 void at91_pmc_init(void) 394 { 395 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 396 u32 tmp; 397 398 tmp = AT91_PMC_PLLAR_29 | 399 AT91_PMC_PLLXR_PLLCOUNT(0x3f) | 400 AT91_PMC_PLLXR_MUL(87) | 401 AT91_PMC_PLLXR_DIV(1); 402 at91_plla_init(tmp); 403 404 writel(0x0 << 8, &pmc->pllicpr); 405 406 tmp = AT91_PMC_MCKR_H32MXDIV | 407 AT91_PMC_MCKR_PLLADIV_2 | 408 AT91_PMC_MCKR_MDIV_3 | 409 AT91_PMC_MCKR_CSS_PLLA; 410 at91_mck_init(tmp); 411 } 412 #endif 413