1 /*
2  * Copyright (C) 2014 Atmel
3  *		      Bo Shen <voice.shen@atmel.com>
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 #include <common.h>
9 #include <asm/io.h>
10 #include <asm/arch/at91_common.h>
11 #include <asm/arch/at91_pmc.h>
12 #include <asm/arch/at91_rstc.h>
13 #include <asm/arch/atmel_mpddrc.h>
14 #include <asm/arch/atmel_usba_udc.h>
15 #include <asm/arch/gpio.h>
16 #include <asm/arch/clk.h>
17 #include <asm/arch/sama5d3_smc.h>
18 #include <asm/arch/sama5d4.h>
19 #include <atmel_hlcdc.h>
20 #include <atmel_mci.h>
21 #include <lcd.h>
22 #include <mmc.h>
23 #include <net.h>
24 #include <netdev.h>
25 #include <nand.h>
26 #include <spi.h>
27 #include <version.h>
28 
29 DECLARE_GLOBAL_DATA_PTR;
30 
31 #ifdef CONFIG_ATMEL_SPI
32 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
33 {
34 	return bus == 0 && cs == 0;
35 }
36 
37 void spi_cs_activate(struct spi_slave *slave)
38 {
39 	at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
40 }
41 
42 void spi_cs_deactivate(struct spi_slave *slave)
43 {
44 	at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
45 }
46 
47 static void sama5d4ek_spi0_hw_init(void)
48 {
49 	at91_set_a_periph(AT91_PIO_PORTC, 0, 0);	/* SPI0_MISO */
50 	at91_set_a_periph(AT91_PIO_PORTC, 1, 0);	/* SPI0_MOSI */
51 	at91_set_a_periph(AT91_PIO_PORTC, 2, 0);	/* SPI0_SPCK */
52 
53 	at91_set_pio_output(AT91_PIO_PORTC, 3, 1);	/* SPI0_CS0 */
54 
55 	/* Enable clock */
56 	at91_periph_clk_enable(ATMEL_ID_SPI0);
57 }
58 #endif /* CONFIG_ATMEL_SPI */
59 
60 #ifdef CONFIG_NAND_ATMEL
61 static void sama5d4ek_nand_hw_init(void)
62 {
63 	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
64 
65 	at91_periph_clk_enable(ATMEL_ID_SMC);
66 
67 	/* Configure SMC CS3 for NAND */
68 	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
69 	       AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1),
70 	       &smc->cs[3].setup);
71 	writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) |
72 	       AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3),
73 	       &smc->cs[3].pulse);
74 	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
75 	       &smc->cs[3].cycle);
76 	writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) |
77 	       AT91_SMC_TIMINGS_TAR(2)  | AT91_SMC_TIMINGS_TRR(3)   |
78 	       AT91_SMC_TIMINGS_TWB(7)  | AT91_SMC_TIMINGS_RBNSEL(3)|
79 	       AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
80 	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
81 	       AT91_SMC_MODE_EXNW_DISABLE |
82 	       AT91_SMC_MODE_DBW_8 |
83 	       AT91_SMC_MODE_TDF_CYCLE(3),
84 	       &smc->cs[3].mode);
85 
86 	at91_set_a_periph(AT91_PIO_PORTC, 5, 0);	/* D0 */
87 	at91_set_a_periph(AT91_PIO_PORTC, 6, 0);	/* D1 */
88 	at91_set_a_periph(AT91_PIO_PORTC, 7, 0);	/* D2 */
89 	at91_set_a_periph(AT91_PIO_PORTC, 8, 0);	/* D3 */
90 	at91_set_a_periph(AT91_PIO_PORTC, 9, 0);	/* D4 */
91 	at91_set_a_periph(AT91_PIO_PORTC, 10, 0);	/* D5 */
92 	at91_set_a_periph(AT91_PIO_PORTC, 11, 0);	/* D6 */
93 	at91_set_a_periph(AT91_PIO_PORTC, 12, 0);	/* D7 */
94 	at91_set_a_periph(AT91_PIO_PORTC, 13, 0);	/* RE */
95 	at91_set_a_periph(AT91_PIO_PORTC, 14, 0);	/* WE */
96 	at91_set_a_periph(AT91_PIO_PORTC, 15, 1);	/* NCS */
97 	at91_set_a_periph(AT91_PIO_PORTC, 16, 1);	/* RDY */
98 	at91_set_a_periph(AT91_PIO_PORTC, 17, 1);	/* ALE */
99 	at91_set_a_periph(AT91_PIO_PORTC, 18, 1);	/* CLE */
100 }
101 #endif
102 
103 #ifdef CONFIG_CMD_USB
104 static void sama5d4ek_usb_hw_init(void)
105 {
106 	at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
107 	at91_set_pio_output(AT91_PIO_PORTE, 12, 0);
108 	at91_set_pio_output(AT91_PIO_PORTE, 10, 0);
109 }
110 #endif
111 
112 #ifdef CONFIG_LCD
113 vidinfo_t panel_info = {
114 	.vl_col = 800,
115 	.vl_row = 480,
116 	.vl_clk = 33260000,
117 	.vl_bpix = LCD_BPP,
118 	.vl_tft = 1,
119 	.vl_hsync_len = 5,
120 	.vl_left_margin = 128,
121 	.vl_right_margin = 0,
122 	.vl_vsync_len = 5,
123 	.vl_upper_margin = 23,
124 	.vl_lower_margin = 22,
125 	.mmio = ATMEL_BASE_LCDC,
126 };
127 
128 /* No power up/down pin for the LCD pannel */
129 void lcd_enable(void)	{ /* Empty! */ }
130 void lcd_disable(void)	{ /* Empty! */ }
131 
132 unsigned int has_lcdc(void)
133 {
134 	return 1;
135 }
136 
137 static void sama5d4ek_lcd_hw_init(void)
138 {
139 	at91_set_a_periph(AT91_PIO_PORTA, 24, 0);	/* LCDPWM */
140 	at91_set_a_periph(AT91_PIO_PORTA, 25, 0);	/* LCDDISP */
141 	at91_set_a_periph(AT91_PIO_PORTA, 26, 0);	/* LCDVSYNC */
142 	at91_set_a_periph(AT91_PIO_PORTA, 27, 0);	/* LCDHSYNC */
143 	at91_set_a_periph(AT91_PIO_PORTA, 28, 0);	/* LCDDOTCK */
144 	at91_set_a_periph(AT91_PIO_PORTA, 29, 0);	/* LCDDEN */
145 
146 	at91_set_a_periph(AT91_PIO_PORTA,  2, 0);	/* LCDD2 */
147 	at91_set_a_periph(AT91_PIO_PORTA,  3, 0);	/* LCDD3 */
148 	at91_set_a_periph(AT91_PIO_PORTA,  4, 0);	/* LCDD4 */
149 	at91_set_a_periph(AT91_PIO_PORTA,  5, 0);	/* LCDD5 */
150 	at91_set_a_periph(AT91_PIO_PORTA,  6, 0);	/* LCDD6 */
151 	at91_set_a_periph(AT91_PIO_PORTA,  7, 0);	/* LCDD7 */
152 
153 	at91_set_a_periph(AT91_PIO_PORTA, 10, 0);	/* LCDD10 */
154 	at91_set_a_periph(AT91_PIO_PORTA, 11, 0);	/* LCDD11 */
155 	at91_set_a_periph(AT91_PIO_PORTA, 12, 0);	/* LCDD12 */
156 	at91_set_a_periph(AT91_PIO_PORTA, 13, 0);	/* LCDD13 */
157 	at91_set_a_periph(AT91_PIO_PORTA, 14, 0);	/* LCDD14 */
158 	at91_set_a_periph(AT91_PIO_PORTA, 15, 0);	/* LCDD15 */
159 
160 	at91_set_a_periph(AT91_PIO_PORTA, 18, 0);	/* LCDD18 */
161 	at91_set_a_periph(AT91_PIO_PORTA, 19, 0);	/* LCDD19 */
162 	at91_set_a_periph(AT91_PIO_PORTA, 20, 0);	/* LCDD20 */
163 	at91_set_a_periph(AT91_PIO_PORTA, 21, 0);	/* LCDD21 */
164 	at91_set_a_periph(AT91_PIO_PORTA, 22, 0);	/* LCDD22 */
165 	at91_set_a_periph(AT91_PIO_PORTA, 23, 0);	/* LCDD23 */
166 
167 	/* Enable clock */
168 	at91_periph_clk_enable(ATMEL_ID_LCDC);
169 }
170 
171 #ifdef CONFIG_LCD_INFO
172 void lcd_show_board_info(void)
173 {
174 	ulong dram_size, nand_size;
175 	int i;
176 	char temp[32];
177 
178 	lcd_printf("%s\n", U_BOOT_VERSION);
179 	lcd_printf("2014 ATMEL Corp\n");
180 	lcd_printf("at91@atmel.com\n");
181 	lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
182 		   strmhz(temp, get_cpu_clk_rate()));
183 
184 	dram_size = 0;
185 	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
186 		dram_size += gd->bd->bi_dram[i].size;
187 
188 	nand_size = 0;
189 #ifdef CONFIG_NAND_ATMEL
190 	for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
191 		nand_size += nand_info[i].size;
192 #endif
193 	lcd_printf("%ld MB SDRAM, %ld MB NAND\n",
194 		   dram_size >> 20, nand_size >> 20);
195 }
196 #endif /* CONFIG_LCD_INFO */
197 
198 #endif /* CONFIG_LCD */
199 
200 #ifdef CONFIG_GENERIC_ATMEL_MCI
201 void sama5d4ek_mci1_hw_init(void)
202 {
203 	at91_set_c_periph(AT91_PIO_PORTE, 19, 1);	/* MCI1 CDA */
204 	at91_set_c_periph(AT91_PIO_PORTE, 20, 1);	/* MCI1 DA0 */
205 	at91_set_c_periph(AT91_PIO_PORTE, 21, 1);	/* MCI1 DA1 */
206 	at91_set_c_periph(AT91_PIO_PORTE, 22, 1);	/* MCI1 DA2 */
207 	at91_set_c_periph(AT91_PIO_PORTE, 23, 1);	/* MCI1 DA3 */
208 	at91_set_c_periph(AT91_PIO_PORTE, 18, 0);	/* MCI1 CLK */
209 
210 	/*
211 	 * As the mci io internal pull down is too strong, so if the io needs
212 	 * external pull up, the pull up resistor will be very small, if so
213 	 * the power consumption will increase, so disable the interanl pull
214 	 * down to save the power.
215 	 */
216 	at91_set_pio_pulldown(AT91_PIO_PORTE, 18, 0);
217 	at91_set_pio_pulldown(AT91_PIO_PORTE, 19, 0);
218 	at91_set_pio_pulldown(AT91_PIO_PORTE, 20, 0);
219 	at91_set_pio_pulldown(AT91_PIO_PORTE, 21, 0);
220 	at91_set_pio_pulldown(AT91_PIO_PORTE, 22, 0);
221 	at91_set_pio_pulldown(AT91_PIO_PORTE, 23, 0);
222 
223 	/* Enable clock */
224 	at91_periph_clk_enable(ATMEL_ID_MCI1);
225 }
226 
227 int board_mmc_init(bd_t *bis)
228 {
229 	/* Enable power for MCI1 interface */
230 	at91_set_pio_output(AT91_PIO_PORTE, 15, 0);
231 
232 	return atmel_mci_init((void *)ATMEL_BASE_MCI1);
233 }
234 #endif /* CONFIG_GENERIC_ATMEL_MCI */
235 
236 #ifdef CONFIG_MACB
237 void sama5d4ek_macb0_hw_init(void)
238 {
239 	at91_set_a_periph(AT91_PIO_PORTB, 0, 0);	/* ETXCK_EREFCK */
240 	at91_set_a_periph(AT91_PIO_PORTB, 6, 0);	/* ERXDV */
241 	at91_set_a_periph(AT91_PIO_PORTB, 8, 0);	/* ERX0 */
242 	at91_set_a_periph(AT91_PIO_PORTB, 9, 0);	/* ERX1 */
243 	at91_set_a_periph(AT91_PIO_PORTB, 7, 0);	/* ERXER */
244 	at91_set_a_periph(AT91_PIO_PORTB, 2, 0);	/* ETXEN */
245 	at91_set_a_periph(AT91_PIO_PORTB, 12, 0);	/* ETX0 */
246 	at91_set_a_periph(AT91_PIO_PORTB, 13, 0);	/* ETX1 */
247 	at91_set_a_periph(AT91_PIO_PORTB, 17, 0);	/* EMDIO */
248 	at91_set_a_periph(AT91_PIO_PORTB, 16, 0);	/* EMDC */
249 
250 	/* Enable clock */
251 	at91_periph_clk_enable(ATMEL_ID_GMAC0);
252 }
253 #endif
254 
255 static void sama5d4ek_serial3_hw_init(void)
256 {
257 	at91_set_b_periph(AT91_PIO_PORTE, 17, 1);	/* TXD3 */
258 	at91_set_b_periph(AT91_PIO_PORTE, 16, 0);	/* RXD3 */
259 
260 	/* Enable clock */
261 	at91_periph_clk_enable(ATMEL_ID_USART3);
262 }
263 
264 int board_early_init_f(void)
265 {
266 	at91_periph_clk_enable(ATMEL_ID_PIOA);
267 	at91_periph_clk_enable(ATMEL_ID_PIOB);
268 	at91_periph_clk_enable(ATMEL_ID_PIOC);
269 	at91_periph_clk_enable(ATMEL_ID_PIOD);
270 	at91_periph_clk_enable(ATMEL_ID_PIOE);
271 
272 	sama5d4ek_serial3_hw_init();
273 
274 	return 0;
275 }
276 
277 int board_init(void)
278 {
279 	/* adress of boot parameters */
280 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
281 
282 #ifdef CONFIG_ATMEL_SPI
283 	sama5d4ek_spi0_hw_init();
284 #endif
285 #ifdef CONFIG_NAND_ATMEL
286 	sama5d4ek_nand_hw_init();
287 #endif
288 #ifdef CONFIG_GENERIC_ATMEL_MCI
289 	sama5d4ek_mci1_hw_init();
290 #endif
291 #ifdef CONFIG_MACB
292 	sama5d4ek_macb0_hw_init();
293 #endif
294 #ifdef CONFIG_LCD
295 	sama5d4ek_lcd_hw_init();
296 #endif
297 #ifdef CONFIG_CMD_USB
298 	sama5d4ek_usb_hw_init();
299 #endif
300 #ifdef CONFIG_USB_GADGET_ATMEL_USBA
301 	at91_udp_hw_init();
302 #endif
303 
304 	return 0;
305 }
306 
307 int dram_init(void)
308 {
309 	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
310 				    CONFIG_SYS_SDRAM_SIZE);
311 	return 0;
312 }
313 
314 int board_eth_init(bd_t *bis)
315 {
316 	int rc = 0;
317 
318 #ifdef CONFIG_MACB
319 	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
320 #endif
321 
322 #ifdef CONFIG_USB_GADGET_ATMEL_USBA
323 	usba_udc_probe(&pdata);
324 #ifdef CONFIG_USB_ETH_RNDIS
325 	usb_eth_initialize(bis);
326 #endif
327 #endif
328 
329 	return rc;
330 }
331 
332 /* SPL */
333 #ifdef CONFIG_SPL_BUILD
334 void spl_board_init(void)
335 {
336 #ifdef CONFIG_SYS_USE_MMC
337 	sama5d4ek_mci1_hw_init();
338 #elif CONFIG_SYS_USE_NANDFLASH
339 	sama5d4ek_nand_hw_init();
340 #elif CONFIG_SYS_USE_SERIALFLASH
341 	sama5d4ek_spi0_hw_init();
342 #endif
343 }
344 
345 static void ddr2_conf(struct atmel_mpddr *ddr2)
346 {
347 	ddr2->md = (ATMEL_MPDDRC_MD_DBW_32_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
348 
349 	ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
350 		    ATMEL_MPDDRC_CR_NR_ROW_14 |
351 		    ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
352 		    ATMEL_MPDDRC_CR_NB_8BANKS |
353 		    ATMEL_MPDDRC_CR_NDQS_DISABLED |
354 		    ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
355 		    ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
356 
357 	ddr2->rtr = 0x2b0;
358 
359 	ddr2->tpr0 = (8 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
360 		      3 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
361 		      3 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
362 		      10 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
363 		      3 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
364 		      2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
365 		      2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
366 		      2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
367 
368 	ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
369 		      200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
370 		      25 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
371 		      23 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
372 
373 	ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET |
374 		      2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
375 		      3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
376 		      2 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
377 		      8 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
378 }
379 
380 void mem_init(void)
381 {
382 	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
383 	struct atmel_mpddr ddr2;
384 
385 	ddr2_conf(&ddr2);
386 
387 	/* enable MPDDR clock */
388 	at91_periph_clk_enable(ATMEL_ID_MPDDRC);
389 	writel(AT91_PMC_DDR, &pmc->scer);
390 
391 	/* DDRAM2 Controller initialize */
392 	ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2);
393 }
394 
395 void at91_pmc_init(void)
396 {
397 	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
398 	u32 tmp;
399 
400 	tmp = AT91_PMC_PLLAR_29 |
401 	      AT91_PMC_PLLXR_PLLCOUNT(0x3f) |
402 	      AT91_PMC_PLLXR_MUL(87) |
403 	      AT91_PMC_PLLXR_DIV(1);
404 	at91_plla_init(tmp);
405 
406 	writel(0x0 << 8, &pmc->pllicpr);
407 
408 	tmp = AT91_PMC_MCKR_H32MXDIV |
409 	      AT91_PMC_MCKR_PLLADIV_2 |
410 	      AT91_PMC_MCKR_MDIV_3 |
411 	      AT91_PMC_MCKR_CSS_PLLA;
412 	at91_mck_init(tmp);
413 }
414 #endif
415