1 /* 2 * Copyright (C) 2012 - 2013 Atmel Corporation 3 * Bo Shen <voice.shen@atmel.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #include <common.h> 9 #include <asm/io.h> 10 #include <asm/arch/sama5d3_smc.h> 11 #include <asm/arch/at91_common.h> 12 #include <asm/arch/at91_rstc.h> 13 #include <asm/arch/gpio.h> 14 #include <asm/arch/clk.h> 15 #include <debug_uart.h> 16 #include <lcd.h> 17 #include <linux/ctype.h> 18 #include <atmel_hlcdc.h> 19 #include <phy.h> 20 #include <micrel.h> 21 #include <spl.h> 22 #include <asm/arch/atmel_mpddrc.h> 23 #include <asm/arch/at91_wdt.h> 24 25 DECLARE_GLOBAL_DATA_PTR; 26 27 /* ------------------------------------------------------------------------- */ 28 /* 29 * Miscelaneous platform dependent initialisations 30 */ 31 32 #ifdef CONFIG_NAND_ATMEL 33 void sama5d3xek_nand_hw_init(void) 34 { 35 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; 36 37 at91_periph_clk_enable(ATMEL_ID_SMC); 38 39 /* Configure SMC CS3 for NAND/SmartMedia */ 40 writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(1) | 41 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(1), 42 &smc->cs[3].setup); 43 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) | 44 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(5), 45 &smc->cs[3].pulse); 46 writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8), 47 &smc->cs[3].cycle); 48 writel(AT91_SMC_TIMINGS_TCLR(3) | AT91_SMC_TIMINGS_TADL(10) | 49 AT91_SMC_TIMINGS_TAR(3) | AT91_SMC_TIMINGS_TRR(4) | 50 AT91_SMC_TIMINGS_TWB(5) | AT91_SMC_TIMINGS_RBNSEL(3)| 51 AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings); 52 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 53 AT91_SMC_MODE_EXNW_DISABLE | 54 #ifdef CONFIG_SYS_NAND_DBW_16 55 AT91_SMC_MODE_DBW_16 | 56 #else /* CONFIG_SYS_NAND_DBW_8 */ 57 AT91_SMC_MODE_DBW_8 | 58 #endif 59 AT91_SMC_MODE_TDF_CYCLE(3), 60 &smc->cs[3].mode); 61 } 62 #endif 63 64 #ifdef CONFIG_MTD_NOR_FLASH 65 static void sama5d3xek_nor_hw_init(void) 66 { 67 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; 68 69 at91_periph_clk_enable(ATMEL_ID_SMC); 70 71 /* Configure SMC CS0 for NOR flash */ 72 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | 73 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), 74 &smc->cs[0].setup); 75 writel(AT91_SMC_PULSE_NWE(10) | AT91_SMC_PULSE_NCS_WR(11) | 76 AT91_SMC_PULSE_NRD(10) | AT91_SMC_PULSE_NCS_RD(11), 77 &smc->cs[0].pulse); 78 writel(AT91_SMC_CYCLE_NWE(11) | AT91_SMC_CYCLE_NRD(14), 79 &smc->cs[0].cycle); 80 writel(AT91_SMC_TIMINGS_TCLR(0) | AT91_SMC_TIMINGS_TADL(0) | 81 AT91_SMC_TIMINGS_TAR(0) | AT91_SMC_TIMINGS_TRR(0) | 82 AT91_SMC_TIMINGS_TWB(0) | AT91_SMC_TIMINGS_RBNSEL(0)| 83 AT91_SMC_TIMINGS_NFSEL(0), &smc->cs[0].timings); 84 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 85 AT91_SMC_MODE_EXNW_DISABLE | 86 AT91_SMC_MODE_DBW_16 | 87 AT91_SMC_MODE_TDF_CYCLE(1), 88 &smc->cs[0].mode); 89 90 /* Address pin (A1 ~ A23) configuration */ 91 at91_pio3_set_a_periph(AT91_PIO_PORTE, 1, 0); 92 at91_pio3_set_a_periph(AT91_PIO_PORTE, 2, 0); 93 at91_pio3_set_a_periph(AT91_PIO_PORTE, 3, 0); 94 at91_pio3_set_a_periph(AT91_PIO_PORTE, 4, 0); 95 at91_pio3_set_a_periph(AT91_PIO_PORTE, 5, 0); 96 at91_pio3_set_a_periph(AT91_PIO_PORTE, 6, 0); 97 at91_pio3_set_a_periph(AT91_PIO_PORTE, 7, 0); 98 at91_pio3_set_a_periph(AT91_PIO_PORTE, 8, 0); 99 at91_pio3_set_a_periph(AT91_PIO_PORTE, 9, 0); 100 at91_pio3_set_a_periph(AT91_PIO_PORTE, 10, 0); 101 at91_pio3_set_a_periph(AT91_PIO_PORTE, 11, 0); 102 at91_pio3_set_a_periph(AT91_PIO_PORTE, 12, 0); 103 at91_pio3_set_a_periph(AT91_PIO_PORTE, 13, 0); 104 at91_pio3_set_a_periph(AT91_PIO_PORTE, 14, 0); 105 at91_pio3_set_a_periph(AT91_PIO_PORTE, 15, 0); 106 at91_pio3_set_a_periph(AT91_PIO_PORTE, 16, 0); 107 at91_pio3_set_a_periph(AT91_PIO_PORTE, 17, 0); 108 at91_pio3_set_a_periph(AT91_PIO_PORTE, 18, 0); 109 at91_pio3_set_a_periph(AT91_PIO_PORTE, 19, 0); 110 at91_pio3_set_a_periph(AT91_PIO_PORTE, 20, 0); 111 at91_pio3_set_a_periph(AT91_PIO_PORTE, 21, 0); 112 at91_pio3_set_a_periph(AT91_PIO_PORTE, 22, 0); 113 at91_pio3_set_a_periph(AT91_PIO_PORTE, 23, 0); 114 /* CS0 pin configuration */ 115 at91_pio3_set_a_periph(AT91_PIO_PORTE, 26, 0); 116 } 117 #endif 118 119 #ifdef CONFIG_CMD_USB 120 static void sama5d3xek_usb_hw_init(void) 121 { 122 at91_set_pio_output(AT91_PIO_PORTD, 25, 0); 123 at91_set_pio_output(AT91_PIO_PORTD, 26, 0); 124 at91_set_pio_output(AT91_PIO_PORTD, 27, 0); 125 } 126 #endif 127 128 #ifdef CONFIG_GENERIC_ATMEL_MCI 129 static void sama5d3xek_mci_hw_init(void) 130 { 131 at91_set_pio_output(AT91_PIO_PORTB, 10, 0); /* MCI0 Power */ 132 } 133 #endif 134 135 #ifdef CONFIG_LCD 136 vidinfo_t panel_info = { 137 .vl_col = 800, 138 .vl_row = 480, 139 .vl_clk = 24000000, 140 .vl_bpix = LCD_BPP, 141 .vl_tft = 1, 142 .vl_hsync_len = 128, 143 .vl_left_margin = 64, 144 .vl_right_margin = 64, 145 .vl_vsync_len = 2, 146 .vl_upper_margin = 22, 147 .vl_lower_margin = 21, 148 .mmio = ATMEL_BASE_LCDC, 149 }; 150 151 void lcd_enable(void) 152 { 153 } 154 155 void lcd_disable(void) 156 { 157 } 158 159 static void sama5d3xek_lcd_hw_init(void) 160 { 161 gd->fb_base = CONFIG_SAMA5D3_LCD_BASE; 162 163 /* The higher 8 bit of LCD is board related */ 164 at91_pio3_set_c_periph(AT91_PIO_PORTC, 14, 0); /* LCDD16 */ 165 at91_pio3_set_c_periph(AT91_PIO_PORTC, 13, 0); /* LCDD17 */ 166 at91_pio3_set_c_periph(AT91_PIO_PORTC, 12, 0); /* LCDD18 */ 167 at91_pio3_set_c_periph(AT91_PIO_PORTC, 11, 0); /* LCDD19 */ 168 at91_pio3_set_c_periph(AT91_PIO_PORTC, 10, 0); /* LCDD20 */ 169 at91_pio3_set_c_periph(AT91_PIO_PORTC, 15, 0); /* LCDD21 */ 170 at91_pio3_set_c_periph(AT91_PIO_PORTE, 27, 0); /* LCDD22 */ 171 at91_pio3_set_c_periph(AT91_PIO_PORTE, 28, 0); /* LCDD23 */ 172 173 /* Configure lower 16 bit of LCD and enable clock */ 174 at91_lcd_hw_init(); 175 } 176 177 #ifdef CONFIG_LCD_INFO 178 #include <nand.h> 179 #include <version.h> 180 181 void lcd_show_board_info(void) 182 { 183 ulong dram_size; 184 uint64_t nand_size; 185 int i; 186 char temp[32]; 187 188 lcd_printf("%s\n", U_BOOT_VERSION); 189 lcd_printf("(C) 2013 ATMEL Corp\n"); 190 lcd_printf("at91@atmel.com\n"); 191 lcd_printf("%s CPU at %s MHz\n", get_cpu_name(), 192 strmhz(temp, get_cpu_clk_rate())); 193 194 dram_size = 0; 195 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) 196 dram_size += gd->bd->bi_dram[i].size; 197 198 nand_size = 0; 199 #ifdef CONFIG_NAND_ATMEL 200 for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) 201 nand_size += get_nand_dev_by_index(i)->size; 202 #endif 203 lcd_printf("%ld MB SDRAM, %lld MB NAND\n", 204 dram_size >> 20, nand_size >> 20); 205 } 206 #endif /* CONFIG_LCD_INFO */ 207 #endif /* CONFIG_LCD */ 208 209 #ifdef CONFIG_DEBUG_UART_BOARD_INIT 210 void board_debug_uart_init(void) 211 { 212 at91_seriald_hw_init(); 213 } 214 #endif 215 216 #ifdef CONFIG_BOARD_EARLY_INIT_F 217 int board_early_init_f(void) 218 { 219 #ifdef CONFIG_DEBUG_UART 220 debug_uart_init(); 221 #endif 222 return 0; 223 } 224 #endif 225 226 int board_init(void) 227 { 228 /* adress of boot parameters */ 229 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 230 231 #ifdef CONFIG_NAND_ATMEL 232 sama5d3xek_nand_hw_init(); 233 #endif 234 #ifdef CONFIG_MTD_NOR_FLASH 235 sama5d3xek_nor_hw_init(); 236 #endif 237 #ifdef CONFIG_CMD_USB 238 sama5d3xek_usb_hw_init(); 239 #endif 240 #ifdef CONFIG_GENERIC_ATMEL_MCI 241 sama5d3xek_mci_hw_init(); 242 #endif 243 #ifdef CONFIG_LCD 244 if (has_lcdc()) 245 sama5d3xek_lcd_hw_init(); 246 #endif 247 return 0; 248 } 249 250 int dram_init(void) 251 { 252 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 253 CONFIG_SYS_SDRAM_SIZE); 254 return 0; 255 } 256 257 #ifdef CONFIG_BOARD_LATE_INIT 258 int board_late_init(void) 259 { 260 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 261 const int MAX_STR_LEN = 32; 262 char name[MAX_STR_LEN], *p; 263 int i; 264 265 strncpy(name, get_cpu_name(), MAX_STR_LEN); 266 for (i = 0, p = name; (*p) && (i < MAX_STR_LEN); p++, i++) 267 *p = tolower(*p); 268 269 strcat(name, "ek.dtb"); 270 setenv("dtb_name", name); 271 #endif 272 return 0; 273 } 274 #endif 275 276 /* SPL */ 277 #ifdef CONFIG_SPL_BUILD 278 void spl_board_init(void) 279 { 280 #if CONFIG_SYS_USE_NANDFLASH 281 sama5d3xek_nand_hw_init(); 282 #endif 283 } 284 285 static void ddr2_conf(struct atmel_mpddrc_config *ddr2) 286 { 287 ddr2->md = (ATMEL_MPDDRC_MD_DBW_32_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM); 288 289 ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 | 290 ATMEL_MPDDRC_CR_NR_ROW_14 | 291 ATMEL_MPDDRC_CR_CAS_DDR_CAS3 | 292 ATMEL_MPDDRC_CR_ENRDM_ON | 293 ATMEL_MPDDRC_CR_NB_8BANKS | 294 ATMEL_MPDDRC_CR_NDQS_DISABLED | 295 ATMEL_MPDDRC_CR_DECOD_INTERLEAVED | 296 ATMEL_MPDDRC_CR_UNAL_SUPPORTED); 297 /* 298 * As the DDR2-SDRAm device requires a refresh time is 7.8125us 299 * when DDR run at 133MHz, so it needs (7.8125us * 133MHz / 10^9) clocks 300 */ 301 ddr2->rtr = 0x411; 302 303 ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET | 304 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET | 305 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | 306 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | 307 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | 308 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | 309 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | 310 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); 311 312 ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | 313 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET | 314 28 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET | 315 26 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET); 316 317 ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET | 318 2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET | 319 2 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET | 320 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET | 321 8 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET); 322 } 323 324 void mem_init(void) 325 { 326 struct atmel_mpddrc_config ddr2; 327 328 ddr2_conf(&ddr2); 329 330 /* Enable MPDDR clock */ 331 at91_periph_clk_enable(ATMEL_ID_MPDDRC); 332 at91_system_clk_enable(AT91_PMC_DDR); 333 334 /* DDRAM2 Controller initialize */ 335 ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2); 336 } 337 338 void at91_pmc_init(void) 339 { 340 u32 tmp; 341 342 tmp = AT91_PMC_PLLAR_29 | 343 AT91_PMC_PLLXR_PLLCOUNT(0x3f) | 344 AT91_PMC_PLLXR_MUL(43) | 345 AT91_PMC_PLLXR_DIV(1); 346 at91_plla_init(tmp); 347 348 at91_pllicpr_init(AT91_PMC_IPLL_PLLA(0x3)); 349 350 tmp = AT91_PMC_MCKR_MDIV_4 | 351 AT91_PMC_MCKR_CSS_PLLA; 352 at91_mck_init(tmp); 353 } 354 #endif 355