1 /* 2 * Copyright (C) 2012 Atmel Corporation 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <asm/io.h> 9 #include <asm/arch/at91sam9x5_matrix.h> 10 #include <asm/arch/at91sam9_smc.h> 11 #include <asm/arch/at91_common.h> 12 #include <asm/arch/at91_rstc.h> 13 #include <asm/arch/clk.h> 14 #include <asm/arch/gpio.h> 15 #include <lcd.h> 16 #include <atmel_hlcdc.h> 17 #include <atmel_mci.h> 18 #ifdef CONFIG_MACB 19 #include <net.h> 20 #endif 21 #include <netdev.h> 22 #ifdef CONFIG_LCD_INFO 23 #include <nand.h> 24 #include <version.h> 25 #endif 26 #ifdef CONFIG_ATMEL_SPI 27 #include <spi.h> 28 #endif 29 30 DECLARE_GLOBAL_DATA_PTR; 31 32 /* ------------------------------------------------------------------------- */ 33 /* 34 * Miscelaneous platform dependent initialisations 35 */ 36 #ifdef CONFIG_CMD_NAND 37 static void at91sam9x5ek_nand_hw_init(void) 38 { 39 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; 40 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; 41 unsigned long csa; 42 43 /* Enable CS3 */ 44 csa = readl(&matrix->ebicsa); 45 csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA; 46 /* NAND flash on D16 */ 47 csa |= AT91_MATRIX_NFD0_ON_D16; 48 49 /* Configure IO drive */ 50 csa &= ~AT91_MATRIX_EBI_EBI_IOSR_NORMAL; 51 52 writel(csa, &matrix->ebicsa); 53 54 /* Configure SMC CS3 for NAND/SmartMedia */ 55 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | 56 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), 57 &smc->cs[3].setup); 58 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) | 59 AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6), 60 &smc->cs[3].pulse); 61 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(6), 62 &smc->cs[3].cycle); 63 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 64 AT91_SMC_MODE_EXNW_DISABLE | 65 #ifdef CONFIG_SYS_NAND_DBW_16 66 AT91_SMC_MODE_DBW_16 | 67 #else /* CONFIG_SYS_NAND_DBW_8 */ 68 AT91_SMC_MODE_DBW_8 | 69 #endif 70 AT91_SMC_MODE_TDF_CYCLE(1), 71 &smc->cs[3].mode); 72 73 at91_periph_clk_enable(ATMEL_ID_PIOCD); 74 75 /* Configure RDY/BSY */ 76 at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); 77 /* Enable NandFlash */ 78 at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); 79 80 at91_pio3_set_a_periph(AT91_PIO_PORTD, 0, 1); /* NAND OE */ 81 at91_pio3_set_a_periph(AT91_PIO_PORTD, 1, 1); /* NAND WE */ 82 at91_pio3_set_a_periph(AT91_PIO_PORTD, 2, 1); /* NAND ALE */ 83 at91_pio3_set_a_periph(AT91_PIO_PORTD, 3, 1); /* NAND CLE */ 84 at91_pio3_set_a_periph(AT91_PIO_PORTD, 6, 1); 85 at91_pio3_set_a_periph(AT91_PIO_PORTD, 7, 1); 86 at91_pio3_set_a_periph(AT91_PIO_PORTD, 8, 1); 87 at91_pio3_set_a_periph(AT91_PIO_PORTD, 9, 1); 88 at91_pio3_set_a_periph(AT91_PIO_PORTD, 10, 1); 89 at91_pio3_set_a_periph(AT91_PIO_PORTD, 11, 1); 90 at91_pio3_set_a_periph(AT91_PIO_PORTD, 12, 1); 91 at91_pio3_set_a_periph(AT91_PIO_PORTD, 13, 1); 92 } 93 #endif 94 95 int board_eth_init(bd_t *bis) 96 { 97 int rc = 0; 98 99 #ifdef CONFIG_MACB 100 if (has_emac0()) 101 rc = macb_eth_initialize(0, 102 (void *)ATMEL_BASE_EMAC0, 0x00); 103 if (has_emac1()) 104 rc = macb_eth_initialize(1, 105 (void *)ATMEL_BASE_EMAC1, 0x00); 106 #endif 107 return rc; 108 } 109 110 #ifdef CONFIG_LCD 111 vidinfo_t panel_info = { 112 .vl_col = 800, 113 .vl_row = 480, 114 .vl_clk = 24000000, 115 .vl_sync = LCDC_LCDCFG5_HSPOL | LCDC_LCDCFG5_VSPOL, 116 .vl_bpix = LCD_BPP, 117 .vl_tft = 1, 118 .vl_clk_pol = 1, 119 .vl_hsync_len = 128, 120 .vl_left_margin = 64, 121 .vl_right_margin = 64, 122 .vl_vsync_len = 2, 123 .vl_upper_margin = 22, 124 .vl_lower_margin = 21, 125 .mmio = ATMEL_BASE_LCDC, 126 }; 127 128 void lcd_enable(void) 129 { 130 if (has_lcdc()) 131 at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 1); /* power up */ 132 } 133 134 void lcd_disable(void) 135 { 136 if (has_lcdc()) 137 at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 0); /* power down */ 138 } 139 140 static void at91sam9x5ek_lcd_hw_init(void) 141 { 142 if (has_lcdc()) { 143 at91_pio3_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDPWM */ 144 at91_pio3_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDVSYNC */ 145 at91_pio3_set_a_periph(AT91_PIO_PORTC, 28, 0); /* LCDHSYNC */ 146 at91_pio3_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDDISP */ 147 at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 0); /* LCDDEN */ 148 at91_pio3_set_a_periph(AT91_PIO_PORTC, 30, 0); /* LCDPCK */ 149 150 at91_pio3_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDD0 */ 151 at91_pio3_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDD1 */ 152 at91_pio3_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDD2 */ 153 at91_pio3_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDD3 */ 154 at91_pio3_set_a_periph(AT91_PIO_PORTC, 4, 0); /* LCDD4 */ 155 at91_pio3_set_a_periph(AT91_PIO_PORTC, 5, 0); /* LCDD5 */ 156 at91_pio3_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD6 */ 157 at91_pio3_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD7 */ 158 at91_pio3_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD8 */ 159 at91_pio3_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD9 */ 160 at91_pio3_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD10 */ 161 at91_pio3_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD11 */ 162 at91_pio3_set_a_periph(AT91_PIO_PORTC, 12, 0); /* LCDD12 */ 163 at91_pio3_set_a_periph(AT91_PIO_PORTC, 13, 0); /* LCDD13 */ 164 at91_pio3_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD14 */ 165 at91_pio3_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD15 */ 166 at91_pio3_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD16 */ 167 at91_pio3_set_a_periph(AT91_PIO_PORTC, 17, 0); /* LCDD17 */ 168 at91_pio3_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD18 */ 169 at91_pio3_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD19 */ 170 at91_pio3_set_a_periph(AT91_PIO_PORTC, 20, 0); /* LCDD20 */ 171 at91_pio3_set_a_periph(AT91_PIO_PORTC, 21, 0); /* LCDD21 */ 172 at91_pio3_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD22 */ 173 at91_pio3_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD23 */ 174 175 at91_periph_clk_enable(ATMEL_ID_LCDC); 176 } 177 } 178 179 #ifdef CONFIG_LCD_INFO 180 void lcd_show_board_info(void) 181 { 182 ulong dram_size, nand_size; 183 int i; 184 char temp[32]; 185 186 if (has_lcdc()) { 187 lcd_printf("%s\n", U_BOOT_VERSION); 188 lcd_printf("(C) 2012 ATMEL Corp\n"); 189 lcd_printf("at91support@atmel.com\n"); 190 lcd_printf("%s CPU at %s MHz\n", 191 get_cpu_name(), 192 strmhz(temp, get_cpu_clk_rate())); 193 194 dram_size = 0; 195 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) 196 dram_size += gd->bd->bi_dram[i].size; 197 nand_size = 0; 198 for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) 199 nand_size += nand_info[i]->size; 200 lcd_printf(" %ld MB SDRAM, %ld MB NAND\n", 201 dram_size >> 20, 202 nand_size >> 20); 203 } 204 } 205 #endif /* CONFIG_LCD_INFO */ 206 #endif /* CONFIG_LCD */ 207 208 /* SPI chip select control */ 209 #ifdef CONFIG_ATMEL_SPI 210 int spi_cs_is_valid(unsigned int bus, unsigned int cs) 211 { 212 return bus == 0 && cs < 2; 213 } 214 215 void spi_cs_activate(struct spi_slave *slave) 216 { 217 switch (slave->cs) { 218 case 1: 219 at91_set_pio_output(AT91_PIO_PORTA, 7, 0); 220 break; 221 case 0: 222 default: 223 at91_set_pio_output(AT91_PIO_PORTA, 14, 0); 224 break; 225 } 226 } 227 228 void spi_cs_deactivate(struct spi_slave *slave) 229 { 230 switch (slave->cs) { 231 case 1: 232 at91_set_pio_output(AT91_PIO_PORTA, 7, 1); 233 break; 234 case 0: 235 default: 236 at91_set_pio_output(AT91_PIO_PORTA, 14, 1); 237 break; 238 } 239 } 240 #endif /* CONFIG_ATMEL_SPI */ 241 242 #ifdef CONFIG_GENERIC_ATMEL_MCI 243 int board_mmc_init(bd_t *bd) 244 { 245 at91_mci_hw_init(); 246 247 return atmel_mci_init((void *)ATMEL_BASE_HSMCI0); 248 } 249 #endif 250 251 int board_early_init_f(void) 252 { 253 at91_seriald_hw_init(); 254 return 0; 255 } 256 257 int board_init(void) 258 { 259 /* arch number of AT91SAM9X5EK-Board */ 260 gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9X5EK; 261 262 /* adress of boot parameters */ 263 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 264 265 #ifdef CONFIG_CMD_NAND 266 at91sam9x5ek_nand_hw_init(); 267 #endif 268 269 #ifdef CONFIG_ATMEL_SPI 270 at91_spi0_hw_init(1 << 4); 271 #endif 272 273 #ifdef CONFIG_MACB 274 at91_macb_hw_init(); 275 #endif 276 277 #if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI) 278 at91_uhp_hw_init(); 279 #endif 280 #ifdef CONFIG_LCD 281 at91sam9x5ek_lcd_hw_init(); 282 #endif 283 return 0; 284 } 285 286 int dram_init(void) 287 { 288 gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE, 289 CONFIG_SYS_SDRAM_SIZE); 290 return 0; 291 } 292 293 #if defined(CONFIG_SPL_BUILD) 294 #include <spl.h> 295 #include <nand.h> 296 297 void at91_spl_board_init(void) 298 { 299 #ifdef CONFIG_SYS_USE_MMC 300 at91_mci_hw_init(); 301 #elif CONFIG_SYS_USE_NANDFLASH 302 at91sam9x5ek_nand_hw_init(); 303 #elif CONFIG_SYS_USE_SPIFLASH 304 at91_spi0_hw_init(1 << 4); 305 #endif 306 } 307 308 #include <asm/arch/atmel_mpddrc.h> 309 static void ddr2_conf(struct atmel_mpddrc_config *ddr2) 310 { 311 ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM); 312 313 ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 | 314 ATMEL_MPDDRC_CR_NR_ROW_13 | 315 ATMEL_MPDDRC_CR_CAS_DDR_CAS3 | 316 ATMEL_MPDDRC_CR_NB_8BANKS | 317 ATMEL_MPDDRC_CR_DECOD_INTERLEAVED); 318 319 ddr2->rtr = 0x411; 320 321 ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET | 322 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET | 323 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | 324 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | 325 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | 326 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | 327 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | 328 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); 329 330 ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | 331 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET | 332 19 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET | 333 18 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET); 334 335 ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET | 336 2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET | 337 3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET | 338 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET | 339 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET); 340 } 341 342 void mem_init(void) 343 { 344 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 345 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; 346 struct atmel_mpddrc_config ddr2; 347 unsigned long csa; 348 349 ddr2_conf(&ddr2); 350 351 /* enable DDR2 clock */ 352 writel(AT91_PMC_DDR, &pmc->scer); 353 354 /* Chip select 1 is for DDR2/SDRAM */ 355 csa = readl(&matrix->ebicsa); 356 csa |= AT91_MATRIX_EBI_CS1A_SDRAMC; 357 csa &= ~AT91_MATRIX_EBI_DBPU_OFF; 358 csa |= AT91_MATRIX_EBI_DBPD_OFF; 359 csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL; 360 writel(csa, &matrix->ebicsa); 361 362 /* DDRAM2 Controller initialize */ 363 ddr2_init(ATMEL_BASE_DDRSDRC, ATMEL_BASE_CS1, &ddr2); 364 } 365 #endif 366