1 /*
2  * (C) Copyright 2007-2008
3  * Stelian Pop <stelian@popies.net>
4  * Lead Tech Design <www.leadtechdesign.com>
5  *
6  * SPDX-License-Identifier:	GPL-2.0+
7  */
8 
9 #include <common.h>
10 #include <debug_uart.h>
11 #include <asm/io.h>
12 #include <asm/mach-types.h>
13 #include <asm/arch/at91sam9rl.h>
14 #include <asm/arch/at91sam9rl_matrix.h>
15 #include <asm/arch/at91sam9_smc.h>
16 #include <asm/arch/at91_common.h>
17 #include <asm/arch/at91_rstc.h>
18 #include <asm/arch/clk.h>
19 #include <asm/arch/gpio.h>
20 
21 #include <lcd.h>
22 #include <atmel_lcdc.h>
23 
24 DECLARE_GLOBAL_DATA_PTR;
25 
26 /* ------------------------------------------------------------------------- */
27 /*
28  * Miscelaneous platform dependent initialisations
29  */
30 
31 #ifdef CONFIG_CMD_NAND
32 static void at91sam9rlek_nand_hw_init(void)
33 {
34 	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
35 	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
36 	unsigned long csa;
37 
38 	/* Enable CS3 */
39 	csa = readl(&matrix->ebicsa);
40 	csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
41 
42 	writel(csa, &matrix->ebicsa);
43 
44 	/* Configure SMC CS3 for NAND/SmartMedia */
45 	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
46 		AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
47 		&smc->cs[3].setup);
48 	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
49 		AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
50 		&smc->cs[3].pulse);
51 	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
52 		&smc->cs[3].cycle);
53 	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
54 		AT91_SMC_MODE_EXNW_DISABLE |
55 #ifdef CONFIG_SYS_NAND_DBW_16
56 		AT91_SMC_MODE_DBW_16 |
57 #else /* CONFIG_SYS_NAND_DBW_8 */
58 		AT91_SMC_MODE_DBW_8 |
59 #endif
60 		AT91_SMC_MODE_TDF_CYCLE(2),
61 		&smc->cs[3].mode);
62 
63 	at91_periph_clk_enable(ATMEL_ID_PIOD);
64 
65 	/* Configure RDY/BSY */
66 	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
67 
68 	/* Enable NandFlash */
69 	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
70 
71 	at91_set_A_periph(AT91_PIN_PB4, 0);		/* NANDOE */
72 	at91_set_A_periph(AT91_PIN_PB5, 0);		/* NANDWE */
73 }
74 #endif
75 
76 #ifdef CONFIG_LCD
77 vidinfo_t panel_info = {
78 	.vl_col =		240,
79 	.vl_row =		320,
80 	.vl_clk =		4965000,
81 	.vl_sync =		ATMEL_LCDC_INVLINE_INVERTED |
82 				ATMEL_LCDC_INVFRAME_INVERTED,
83 	.vl_bpix =		3,
84 	.vl_tft =		1,
85 	.vl_hsync_len =		5,
86 	.vl_left_margin =	1,
87 	.vl_right_margin =	33,
88 	.vl_vsync_len =		1,
89 	.vl_upper_margin =	1,
90 	.vl_lower_margin =	0,
91 	.mmio =			ATMEL_BASE_LCDC,
92 };
93 
94 void lcd_enable(void)
95 {
96 	at91_set_gpio_value(AT91_PIN_PA30, 0);  /* power up */
97 }
98 
99 void lcd_disable(void)
100 {
101 	at91_set_gpio_value(AT91_PIN_PA30, 1);  /* power down */
102 }
103 static void at91sam9rlek_lcd_hw_init(void)
104 {
105 	at91_set_B_periph(AT91_PIN_PC1, 0);	/* LCDPWR */
106 	at91_set_A_periph(AT91_PIN_PC5, 0);	/* LCDHSYNC */
107 	at91_set_A_periph(AT91_PIN_PC6, 0);	/* LCDDOTCK */
108 	at91_set_A_periph(AT91_PIN_PC7, 0);	/* LCDDEN */
109 	at91_set_A_periph(AT91_PIN_PC3, 0);	/* LCDCC */
110 	at91_set_B_periph(AT91_PIN_PC9, 0);	/* LCDD3 */
111 	at91_set_B_periph(AT91_PIN_PC10, 0);	/* LCDD4 */
112 	at91_set_B_periph(AT91_PIN_PC11, 0);	/* LCDD5 */
113 	at91_set_B_periph(AT91_PIN_PC12, 0);	/* LCDD6 */
114 	at91_set_B_periph(AT91_PIN_PC13, 0);	/* LCDD7 */
115 	at91_set_B_periph(AT91_PIN_PC15, 0);	/* LCDD11 */
116 	at91_set_B_periph(AT91_PIN_PC16, 0);	/* LCDD12 */
117 	at91_set_B_periph(AT91_PIN_PC17, 0);	/* LCDD13 */
118 	at91_set_B_periph(AT91_PIN_PC18, 0);	/* LCDD14 */
119 	at91_set_B_periph(AT91_PIN_PC19, 0);	/* LCDD15 */
120 	at91_set_B_periph(AT91_PIN_PC20, 0);	/* LCDD18 */
121 	at91_set_B_periph(AT91_PIN_PC21, 0);	/* LCDD19 */
122 	at91_set_B_periph(AT91_PIN_PC22, 0);	/* LCDD20 */
123 	at91_set_B_periph(AT91_PIN_PC23, 0);	/* LCDD21 */
124 	at91_set_B_periph(AT91_PIN_PC24, 0);	/* LCDD22 */
125 	at91_set_B_periph(AT91_PIN_PC25, 0);	/* LCDD23 */
126 
127 	at91_periph_clk_enable(ATMEL_ID_LCDC);
128 }
129 
130 #ifdef CONFIG_LCD_INFO
131 #include <nand.h>
132 #include <version.h>
133 
134 void lcd_show_board_info(void)
135 {
136 	ulong dram_size, nand_size;
137 	int i;
138 	char temp[32];
139 
140 	lcd_printf ("%s\n", U_BOOT_VERSION);
141 	lcd_printf ("(C) 2008 ATMEL Corp\n");
142 	lcd_printf ("at91support@atmel.com\n");
143 	lcd_printf ("%s CPU at %s MHz\n",
144 		ATMEL_CPU_NAME,
145 		strmhz(temp, get_cpu_clk_rate()));
146 
147 	dram_size = 0;
148 	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
149 		dram_size += gd->bd->bi_dram[i].size;
150 	nand_size = 0;
151 	for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
152 		nand_size += nand_info[i]->size;
153 	lcd_printf ("  %ld MB SDRAM, %ld MB NAND\n",
154 		dram_size >> 20,
155 		nand_size >> 20 );
156 }
157 #endif /* CONFIG_LCD_INFO */
158 #endif
159 
160 #ifdef CONFIG_DEBUG_UART_BOARD_INIT
161 void board_debug_uart_init(void)
162 {
163 	at91_seriald_hw_init();
164 }
165 #endif
166 
167 #ifdef CONFIG_BOARD_EARLY_INIT_F
168 int board_early_init_f(void)
169 {
170 #ifdef CONFIG_DEBUG_UART
171 	debug_uart_init();
172 #endif
173 	return 0;
174 }
175 #endif
176 
177 int board_init(void)
178 {
179 	/* arch number of AT91SAM9RLEK-Board */
180 	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9RLEK;
181 	/* adress of boot parameters */
182 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
183 
184 #ifdef CONFIG_CMD_NAND
185 	at91sam9rlek_nand_hw_init();
186 #endif
187 #ifdef CONFIG_HAS_DATAFLASH
188 	at91_spi0_hw_init(1 << 0);
189 #endif
190 #ifdef CONFIG_LCD
191 	at91sam9rlek_lcd_hw_init();
192 #endif
193 	return 0;
194 }
195 
196 int dram_init(void)
197 {
198 	gd->ram_size = get_ram_size(
199 		(void *)CONFIG_SYS_SDRAM_BASE,
200 		CONFIG_SYS_SDRAM_SIZE);
201 	return 0;
202 }
203