1 /* 2 * (C) Copyright 2007-2008 3 * Stelian Pop <stelian@popies.net> 4 * Lead Tech Design <www.leadtechdesign.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <linux/sizes.h> 11 #include <asm/arch/at91sam9263.h> 12 #include <asm/arch/at91sam9_smc.h> 13 #include <asm/arch/at91_common.h> 14 #include <asm/arch/at91_pmc.h> 15 #include <asm/arch/at91_matrix.h> 16 #include <asm/arch/at91_pio.h> 17 #include <asm/arch/clk.h> 18 #include <asm/io.h> 19 #include <asm/arch/gpio.h> 20 #include <asm/arch/hardware.h> 21 #include <lcd.h> 22 #include <atmel_lcdc.h> 23 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) 24 #include <net.h> 25 #endif 26 #include <netdev.h> 27 #include <atmel_mci.h> 28 29 DECLARE_GLOBAL_DATA_PTR; 30 31 /* ------------------------------------------------------------------------- */ 32 /* 33 * Miscelaneous platform dependent initialisations 34 */ 35 36 #ifdef CONFIG_CMD_NAND 37 static void at91sam9263ek_nand_hw_init(void) 38 { 39 unsigned long csa; 40 at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0; 41 at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX; 42 at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; 43 44 /* Enable CS3 */ 45 csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A; 46 writel(csa, &matrix->csa[0]); 47 48 /* Enable CS3 */ 49 50 /* Configure SMC CS3 for NAND/SmartMedia */ 51 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | 52 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), 53 &smc->cs[3].setup); 54 55 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | 56 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), 57 &smc->cs[3].pulse); 58 59 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), 60 &smc->cs[3].cycle); 61 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 62 AT91_SMC_MODE_EXNW_DISABLE | 63 #ifdef CONFIG_SYS_NAND_DBW_16 64 AT91_SMC_MODE_DBW_16 | 65 #else /* CONFIG_SYS_NAND_DBW_8 */ 66 AT91_SMC_MODE_DBW_8 | 67 #endif 68 AT91_SMC_MODE_TDF_CYCLE(2), 69 &smc->cs[3].mode); 70 71 writel(1 << ATMEL_ID_PIOA | 1 << ATMEL_ID_PIOCDE, 72 &pmc->pcer); 73 74 /* Configure RDY/BSY */ 75 at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); 76 77 /* Enable NandFlash */ 78 at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); 79 } 80 #endif 81 82 #ifdef CONFIG_MACB 83 static void at91sam9263ek_macb_hw_init(void) 84 { 85 at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; 86 at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; 87 88 /* Enable clock */ 89 writel(1 << ATMEL_ID_EMAC, &pmc->pcer); 90 91 /* 92 * Disable pull-up on: 93 * RXDV (PC25) => PHY normal mode (not Test mode) 94 * ERX0 (PE25) => PHY ADDR0 95 * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0 96 * 97 * PHY has internal pull-down 98 */ 99 writel(1 << 25, &pio->pioc.pudr); 100 writel((1 << 25) | (1 <<26), &pio->pioe.pudr); 101 102 at91_phy_reset(); 103 104 /* Re-enable pull-up */ 105 writel(1 << 25, &pio->pioc.puer); 106 writel((1 << 25) | (1 <<26), &pio->pioe.puer); 107 108 at91_macb_hw_init(); 109 } 110 #endif 111 112 #ifdef CONFIG_LCD 113 vidinfo_t panel_info = { 114 vl_col: 240, 115 vl_row: 320, 116 vl_clk: 4965000, 117 vl_sync: ATMEL_LCDC_INVLINE_INVERTED | 118 ATMEL_LCDC_INVFRAME_INVERTED, 119 vl_bpix: 3, 120 vl_tft: 1, 121 vl_hsync_len: 5, 122 vl_left_margin: 1, 123 vl_right_margin:33, 124 vl_vsync_len: 1, 125 vl_upper_margin:1, 126 vl_lower_margin:0, 127 mmio: ATMEL_BASE_LCDC, 128 }; 129 130 void lcd_enable(void) 131 { 132 at91_set_pio_value(AT91_PIO_PORTA, 30, 1); /* power up */ 133 } 134 135 void lcd_disable(void) 136 { 137 at91_set_pio_value(AT91_PIO_PORTA, 30, 0); /* power down */ 138 } 139 140 static void at91sam9263ek_lcd_hw_init(void) 141 { 142 at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; 143 144 at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */ 145 at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */ 146 at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */ 147 at91_set_b_periph(AT91_PIO_PORTB, 9, 0); /* LCDCC */ 148 at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD2 */ 149 at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD3 */ 150 at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD4 */ 151 at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD5 */ 152 at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD6 */ 153 at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD7 */ 154 at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD10 */ 155 at91_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD11 */ 156 at91_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD12 */ 157 at91_set_b_periph(AT91_PIO_PORTC, 12, 0); /* LCDD13 */ 158 at91_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD14 */ 159 at91_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD15 */ 160 at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD18 */ 161 at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD19 */ 162 at91_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDD20 */ 163 at91_set_b_periph(AT91_PIO_PORTC, 17, 0); /* LCDD21 */ 164 at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */ 165 at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */ 166 167 writel(1 << ATMEL_ID_LCDC, &pmc->pcer); 168 gd->fb_base = ATMEL_BASE_SRAM0; 169 } 170 171 #ifdef CONFIG_LCD_INFO 172 #include <nand.h> 173 #include <version.h> 174 175 #ifndef CONFIG_SYS_NO_FLASH 176 extern flash_info_t flash_info[]; 177 #endif 178 179 void lcd_show_board_info(void) 180 { 181 ulong dram_size, nand_size; 182 #ifndef CONFIG_SYS_NO_FLASH 183 ulong flash_size; 184 #endif 185 int i; 186 char temp[32]; 187 188 lcd_printf ("%s\n", U_BOOT_VERSION); 189 lcd_printf ("(C) 2008 ATMEL Corp\n"); 190 lcd_printf ("at91support@atmel.com\n"); 191 lcd_printf ("%s CPU at %s MHz\n", 192 ATMEL_CPU_NAME, 193 strmhz(temp, get_cpu_clk_rate())); 194 195 dram_size = 0; 196 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) 197 dram_size += gd->bd->bi_dram[i].size; 198 nand_size = 0; 199 for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) 200 nand_size += nand_info[i].size; 201 #ifndef CONFIG_SYS_NO_FLASH 202 flash_size = 0; 203 for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) 204 flash_size += flash_info[i].size; 205 #endif 206 lcd_printf (" %ld MB SDRAM, %ld MB NAND", 207 dram_size >> 20, 208 nand_size >> 20 ); 209 #ifndef CONFIG_SYS_NO_FLASH 210 lcd_printf (",\n %ld MB NOR", 211 flash_size >> 20); 212 #endif 213 lcd_puts ("\n"); 214 } 215 #endif /* CONFIG_LCD_INFO */ 216 #endif 217 218 #ifdef CONFIG_GENERIC_ATMEL_MCI 219 int board_mmc_init(bd_t *bd) 220 { 221 at91_mci_hw_init(); 222 223 return atmel_mci_init((void *)ATMEL_BASE_MCI1); 224 } 225 #endif 226 227 int board_early_init_f(void) 228 { 229 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 230 231 /* Enable clocks for all PIOs */ 232 writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | 233 (1 << ATMEL_ID_PIOCDE), 234 &pmc->pcer); 235 236 at91_seriald_hw_init(); 237 return 0; 238 } 239 240 int board_init(void) 241 { 242 /* arch number of AT91SAM9263EK-Board */ 243 gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9263EK; 244 /* adress of boot parameters */ 245 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 246 247 #ifdef CONFIG_CMD_NAND 248 at91sam9263ek_nand_hw_init(); 249 #endif 250 #ifdef CONFIG_HAS_DATAFLASH 251 at91_set_pio_output(AT91_PIO_PORTE, 20, 1); /* select spi0 clock */ 252 at91_spi0_hw_init(1 << 0); 253 #endif 254 #ifdef CONFIG_MACB 255 at91sam9263ek_macb_hw_init(); 256 #endif 257 #ifdef CONFIG_USB_OHCI_NEW 258 at91_uhp_hw_init(); 259 #endif 260 #ifdef CONFIG_LCD 261 at91sam9263ek_lcd_hw_init(); 262 #endif 263 return 0; 264 } 265 266 int dram_init(void) 267 { 268 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 269 CONFIG_SYS_SDRAM_SIZE); 270 271 return 0; 272 } 273 274 #ifdef CONFIG_RESET_PHY_R 275 void reset_phy(void) 276 { 277 } 278 #endif 279 280 int board_eth_init(bd_t *bis) 281 { 282 int rc = 0; 283 #ifdef CONFIG_MACB 284 rc = macb_eth_initialize(0, (void *) ATMEL_BASE_EMAC, 0x00); 285 #endif 286 return rc; 287 } 288