1 /* 2 * (C) Copyright 2007-2008 3 * Stelian Pop <stelian@popies.net> 4 * Lead Tech Design <www.leadtechdesign.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <asm/io.h> 11 #include <asm/arch/at91sam9261.h> 12 #include <asm/arch/at91sam9261_matrix.h> 13 #include <asm/arch/at91sam9_smc.h> 14 #include <asm/arch/at91_common.h> 15 #include <asm/arch/at91_pmc.h> 16 #include <asm/arch/at91_rstc.h> 17 #include <asm/arch/clk.h> 18 #include <asm/arch/gpio.h> 19 #include <lcd.h> 20 #include <atmel_lcdc.h> 21 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000) 22 #include <net.h> 23 #include <netdev.h> 24 #endif 25 26 DECLARE_GLOBAL_DATA_PTR; 27 28 /* ------------------------------------------------------------------------- */ 29 /* 30 * Miscelaneous platform dependent initialisations 31 */ 32 33 #ifdef CONFIG_CMD_NAND 34 static void at91sam9261ek_nand_hw_init(void) 35 { 36 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; 37 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; 38 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 39 unsigned long csa; 40 41 /* Enable CS3 */ 42 csa = readl(&matrix->ebicsa); 43 csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA; 44 45 writel(csa, &matrix->ebicsa); 46 47 /* Configure SMC CS3 for NAND/SmartMedia */ 48 #ifdef CONFIG_AT91SAM9G10EK 49 writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) | 50 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), 51 &smc->cs[3].setup); 52 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) | 53 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7), 54 &smc->cs[3].pulse); 55 writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7), 56 &smc->cs[3].cycle); 57 #else 58 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | 59 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), 60 &smc->cs[3].setup); 61 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | 62 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), 63 &smc->cs[3].pulse); 64 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), 65 &smc->cs[3].cycle); 66 #endif 67 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 68 AT91_SMC_MODE_EXNW_DISABLE | 69 #ifdef CONFIG_SYS_NAND_DBW_16 70 AT91_SMC_MODE_DBW_16 | 71 #else /* CONFIG_SYS_NAND_DBW_8 */ 72 AT91_SMC_MODE_DBW_8 | 73 #endif 74 AT91_SMC_MODE_TDF_CYCLE(2), 75 &smc->cs[3].mode); 76 77 writel(1 << ATMEL_ID_PIOC, &pmc->pcer); 78 79 /* Configure RDY/BSY */ 80 at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); 81 82 /* Enable NandFlash */ 83 at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); 84 85 at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */ 86 at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */ 87 } 88 #endif 89 90 #ifdef CONFIG_DRIVER_DM9000 91 static void at91sam9261ek_dm9000_hw_init(void) 92 { 93 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; 94 95 /* Configure SMC CS2 for DM9000 */ 96 #ifdef CONFIG_AT91SAM9G10EK 97 writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) | 98 AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0), 99 &smc->cs[2].setup); 100 writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) | 101 AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8), 102 &smc->cs[2].pulse); 103 writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20), 104 &smc->cs[2].cycle); 105 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 106 AT91_SMC_MODE_EXNW_DISABLE | 107 AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | 108 AT91_SMC_MODE_TDF_CYCLE(1), 109 &smc->cs[2].mode); 110 #else 111 writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) | 112 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), 113 &smc->cs[2].setup); 114 writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) | 115 AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8), 116 &smc->cs[2].pulse); 117 writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16), 118 &smc->cs[2].cycle); 119 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 120 AT91_SMC_MODE_EXNW_DISABLE | 121 AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | 122 AT91_SMC_MODE_TDF_CYCLE(1), 123 &smc->cs[2].mode); 124 #endif 125 126 /* Configure Reset signal as output */ 127 at91_set_gpio_output(AT91_PIN_PC10, 0); 128 129 /* Configure Interrupt pin as input, no pull-up */ 130 at91_set_gpio_input(AT91_PIN_PC11, 0); 131 } 132 #endif 133 134 #ifdef CONFIG_LCD 135 vidinfo_t panel_info = { 136 vl_col: 240, 137 vl_row: 320, 138 vl_clk: 4965000, 139 vl_sync: ATMEL_LCDC_INVLINE_INVERTED | 140 ATMEL_LCDC_INVFRAME_INVERTED, 141 vl_bpix: 3, 142 vl_tft: 1, 143 vl_hsync_len: 5, 144 vl_left_margin: 1, 145 vl_right_margin:33, 146 vl_vsync_len: 1, 147 vl_upper_margin:1, 148 vl_lower_margin:0, 149 mmio: ATMEL_BASE_LCDC, 150 }; 151 152 void lcd_enable(void) 153 { 154 at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */ 155 } 156 157 void lcd_disable(void) 158 { 159 at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */ 160 } 161 162 static void at91sam9261ek_lcd_hw_init(void) 163 { 164 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; 165 166 at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */ 167 at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */ 168 at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */ 169 at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */ 170 at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */ 171 at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */ 172 at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */ 173 at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */ 174 at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */ 175 at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */ 176 at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */ 177 at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */ 178 at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */ 179 at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */ 180 at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */ 181 at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */ 182 at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */ 183 at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */ 184 at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */ 185 at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */ 186 at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */ 187 at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */ 188 189 writel(AT91_PMC_HCK1, &pmc->scer); 190 191 /* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */ 192 #ifdef CONFIG_AT91SAM9261EK 193 gd->fb_base = ATMEL_BASE_SRAM; 194 #endif 195 } 196 197 #ifdef CONFIG_LCD_INFO 198 #include <nand.h> 199 #include <version.h> 200 201 void lcd_show_board_info(void) 202 { 203 ulong dram_size, nand_size; 204 int i; 205 char temp[32]; 206 207 lcd_printf ("%s\n", U_BOOT_VERSION); 208 lcd_printf ("(C) 2008 ATMEL Corp\n"); 209 lcd_printf ("at91support@atmel.com\n"); 210 lcd_printf ("%s CPU at %s MHz\n", 211 ATMEL_CPU_NAME, 212 strmhz(temp, get_cpu_clk_rate())); 213 214 dram_size = 0; 215 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) 216 dram_size += gd->bd->bi_dram[i].size; 217 nand_size = 0; 218 for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) 219 nand_size += nand_info[i].size; 220 lcd_printf (" %ld MB SDRAM, %ld MB NAND\n", 221 dram_size >> 20, 222 nand_size >> 20 ); 223 } 224 #endif /* CONFIG_LCD_INFO */ 225 #endif 226 227 int board_init(void) 228 { 229 #ifdef CONFIG_AT91SAM9G10EK 230 /* arch number of AT91SAM9G10EK-Board */ 231 gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK; 232 #else 233 /* arch number of AT91SAM9261EK-Board */ 234 gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK; 235 #endif 236 /* adress of boot parameters */ 237 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 238 239 at91_seriald_hw_init(); 240 #ifdef CONFIG_CMD_NAND 241 at91sam9261ek_nand_hw_init(); 242 #endif 243 #ifdef CONFIG_HAS_DATAFLASH 244 at91_spi0_hw_init(1 << 0); 245 #endif 246 #ifdef CONFIG_DRIVER_DM9000 247 at91sam9261ek_dm9000_hw_init(); 248 #endif 249 #ifdef CONFIG_LCD 250 at91sam9261ek_lcd_hw_init(); 251 #endif 252 return 0; 253 } 254 255 #ifdef CONFIG_DRIVER_DM9000 256 int board_eth_init(bd_t *bis) 257 { 258 return dm9000_initialize(bis); 259 } 260 #endif 261 262 int dram_init(void) 263 { 264 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 265 CONFIG_SYS_SDRAM_SIZE); 266 267 return 0; 268 } 269 270 #ifdef CONFIG_RESET_PHY_R 271 void reset_phy(void) 272 { 273 #ifdef CONFIG_DRIVER_DM9000 274 /* 275 * Initialize ethernet HW addr prior to starting Linux, 276 * needed for nfsroot 277 */ 278 eth_init(gd->bd); 279 #endif 280 } 281 #endif 282