1 /* 2 * (C) Copyright 2007-2008 3 * Stelian Pop <stelian@popies.net> 4 * Lead Tech Design <www.leadtechdesign.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <asm/io.h> 11 #include <asm/arch/at91sam9261.h> 12 #include <asm/arch/at91sam9261_matrix.h> 13 #include <asm/arch/at91sam9_smc.h> 14 #include <asm/arch/at91_common.h> 15 #include <asm/arch/at91_rstc.h> 16 #include <asm/arch/clk.h> 17 #include <asm/arch/gpio.h> 18 #include <lcd.h> 19 #include <atmel_lcdc.h> 20 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000) 21 #include <net.h> 22 #include <netdev.h> 23 #endif 24 25 DECLARE_GLOBAL_DATA_PTR; 26 27 /* ------------------------------------------------------------------------- */ 28 /* 29 * Miscelaneous platform dependent initialisations 30 */ 31 32 #ifdef CONFIG_CMD_NAND 33 static void at91sam9261ek_nand_hw_init(void) 34 { 35 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; 36 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; 37 unsigned long csa; 38 39 /* Enable CS3 */ 40 csa = readl(&matrix->ebicsa); 41 csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA; 42 43 writel(csa, &matrix->ebicsa); 44 45 /* Configure SMC CS3 for NAND/SmartMedia */ 46 #ifdef CONFIG_AT91SAM9G10EK 47 writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) | 48 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), 49 &smc->cs[3].setup); 50 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) | 51 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7), 52 &smc->cs[3].pulse); 53 writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7), 54 &smc->cs[3].cycle); 55 #else 56 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | 57 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), 58 &smc->cs[3].setup); 59 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | 60 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), 61 &smc->cs[3].pulse); 62 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), 63 &smc->cs[3].cycle); 64 #endif 65 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 66 AT91_SMC_MODE_EXNW_DISABLE | 67 #ifdef CONFIG_SYS_NAND_DBW_16 68 AT91_SMC_MODE_DBW_16 | 69 #else /* CONFIG_SYS_NAND_DBW_8 */ 70 AT91_SMC_MODE_DBW_8 | 71 #endif 72 AT91_SMC_MODE_TDF_CYCLE(2), 73 &smc->cs[3].mode); 74 75 at91_periph_clk_enable(ATMEL_ID_PIOC); 76 77 /* Configure RDY/BSY */ 78 at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); 79 80 /* Enable NandFlash */ 81 at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); 82 83 at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */ 84 at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */ 85 } 86 #endif 87 88 #ifdef CONFIG_DRIVER_DM9000 89 static void at91sam9261ek_dm9000_hw_init(void) 90 { 91 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; 92 93 /* Configure SMC CS2 for DM9000 */ 94 #ifdef CONFIG_AT91SAM9G10EK 95 writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) | 96 AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0), 97 &smc->cs[2].setup); 98 writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) | 99 AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8), 100 &smc->cs[2].pulse); 101 writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20), 102 &smc->cs[2].cycle); 103 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 104 AT91_SMC_MODE_EXNW_DISABLE | 105 AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | 106 AT91_SMC_MODE_TDF_CYCLE(1), 107 &smc->cs[2].mode); 108 #else 109 writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) | 110 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), 111 &smc->cs[2].setup); 112 writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) | 113 AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8), 114 &smc->cs[2].pulse); 115 writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16), 116 &smc->cs[2].cycle); 117 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | 118 AT91_SMC_MODE_EXNW_DISABLE | 119 AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | 120 AT91_SMC_MODE_TDF_CYCLE(1), 121 &smc->cs[2].mode); 122 #endif 123 124 /* Configure Reset signal as output */ 125 at91_set_gpio_output(AT91_PIN_PC10, 0); 126 127 /* Configure Interrupt pin as input, no pull-up */ 128 at91_set_gpio_input(AT91_PIN_PC11, 0); 129 } 130 #endif 131 132 #ifdef CONFIG_LCD 133 vidinfo_t panel_info = { 134 .vl_col = 240, 135 .vl_row = 320, 136 .vl_clk = 4965000, 137 .vl_sync = ATMEL_LCDC_INVLINE_INVERTED | 138 ATMEL_LCDC_INVFRAME_INVERTED, 139 .vl_bpix = 3, 140 .vl_tft = 1, 141 .vl_hsync_len = 5, 142 .vl_left_margin = 1, 143 .vl_right_margin = 33, 144 .vl_vsync_len = 1, 145 .vl_upper_margin = 1, 146 .vl_lower_margin = 0, 147 .mmio = ATMEL_BASE_LCDC, 148 }; 149 150 void lcd_enable(void) 151 { 152 at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */ 153 } 154 155 void lcd_disable(void) 156 { 157 at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */ 158 } 159 160 static void at91sam9261ek_lcd_hw_init(void) 161 { 162 at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */ 163 at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */ 164 at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */ 165 at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */ 166 at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */ 167 at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */ 168 at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */ 169 at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */ 170 at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */ 171 at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */ 172 at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */ 173 at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */ 174 at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */ 175 at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */ 176 at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */ 177 at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */ 178 at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */ 179 at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */ 180 at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */ 181 at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */ 182 at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */ 183 at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */ 184 185 at91_system_clk_enable(AT91_PMC_HCK1); 186 187 /* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */ 188 #ifdef CONFIG_AT91SAM9261EK 189 gd->fb_base = ATMEL_BASE_SRAM; 190 #endif 191 } 192 193 #ifdef CONFIG_LCD_INFO 194 #include <nand.h> 195 #include <version.h> 196 197 void lcd_show_board_info(void) 198 { 199 ulong dram_size, nand_size; 200 int i; 201 char temp[32]; 202 203 lcd_printf ("%s\n", U_BOOT_VERSION); 204 lcd_printf ("(C) 2008 ATMEL Corp\n"); 205 lcd_printf ("at91support@atmel.com\n"); 206 lcd_printf ("%s CPU at %s MHz\n", 207 ATMEL_CPU_NAME, 208 strmhz(temp, get_cpu_clk_rate())); 209 210 dram_size = 0; 211 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) 212 dram_size += gd->bd->bi_dram[i].size; 213 nand_size = 0; 214 for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) 215 nand_size += nand_info[i]->size; 216 lcd_printf (" %ld MB SDRAM, %ld MB NAND\n", 217 dram_size >> 20, 218 nand_size >> 20 ); 219 } 220 #endif /* CONFIG_LCD_INFO */ 221 #endif 222 223 int board_init(void) 224 { 225 #ifdef CONFIG_AT91SAM9G10EK 226 /* arch number of AT91SAM9G10EK-Board */ 227 gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK; 228 #else 229 /* arch number of AT91SAM9261EK-Board */ 230 gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK; 231 #endif 232 /* adress of boot parameters */ 233 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 234 235 at91_seriald_hw_init(); 236 #ifdef CONFIG_CMD_NAND 237 at91sam9261ek_nand_hw_init(); 238 #endif 239 #ifdef CONFIG_HAS_DATAFLASH 240 at91_spi0_hw_init(1 << 0); 241 #endif 242 #ifdef CONFIG_DRIVER_DM9000 243 at91sam9261ek_dm9000_hw_init(); 244 #endif 245 #ifdef CONFIG_LCD 246 at91sam9261ek_lcd_hw_init(); 247 #endif 248 return 0; 249 } 250 251 #ifdef CONFIG_DRIVER_DM9000 252 int board_eth_init(bd_t *bis) 253 { 254 return dm9000_initialize(bis); 255 } 256 #endif 257 258 int dram_init(void) 259 { 260 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 261 CONFIG_SYS_SDRAM_SIZE); 262 263 return 0; 264 } 265 266 #ifdef CONFIG_RESET_PHY_R 267 void reset_phy(void) 268 { 269 #ifdef CONFIG_DRIVER_DM9000 270 /* 271 * Initialize ethernet HW addr prior to starting Linux, 272 * needed for nfsroot 273 */ 274 eth_init(); 275 #endif 276 } 277 #endif 278