1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2015 4 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 5 * 6 * Based on: 7 * Copyright (C) 2012 Freescale Semiconductor, Inc. 8 * 9 * Author: Fabio Estevam <fabio.estevam@freescale.com> 10 */ 11 12 #include <asm/arch/clock.h> 13 #include <asm/arch/imx-regs.h> 14 #include <asm/arch/iomux.h> 15 #include <asm/arch/mx6-pins.h> 16 #include <linux/errno.h> 17 #include <asm/gpio.h> 18 #include <asm/mach-imx/iomux-v3.h> 19 #include <asm/mach-imx/boot_mode.h> 20 #include <asm/mach-imx/mxc_i2c.h> 21 #include <asm/mach-imx/video.h> 22 #include <mmc.h> 23 #include <fsl_esdhc.h> 24 #include <miiphy.h> 25 #include <netdev.h> 26 #include <asm/arch/mxc_hdmi.h> 27 #include <asm/arch/crm_regs.h> 28 #include <linux/fb.h> 29 #include <ipu_pixfmt.h> 30 #include <asm/io.h> 31 #include <asm/arch/sys_proto.h> 32 #include <pwm.h> 33 #include <micrel.h> 34 #include <spi.h> 35 #include <video.h> 36 #include <../drivers/video/ipu.h> 37 #if defined(CONFIG_VIDEO_BMP_LOGO) 38 #include <bmp_logo.h> 39 #endif 40 41 #define USDHC2_PAD_CTRL (PAD_CTL_SPEED_LOW | \ 42 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 43 44 #if (CONFIG_SYS_BOARD_VERSION == 2) 45 /* 4.3 display controller */ 46 #define ECSPI1_CS0 IMX_GPIO_NR(4, 9) 47 #define ECSPI4_CS0 IMX_GPIO_NR(3, 29) 48 #elif (CONFIG_SYS_BOARD_VERSION == 3) 49 #define ECSPI1_CS0 IMX_GPIO_NR(2, 30) /* NOR flash */ 50 /* 4.3 display controller */ 51 #define ECSPI1_CS1 IMX_GPIO_NR(4, 10) 52 #endif 53 54 #define SOFT_RESET_GPIO IMX_GPIO_NR(7, 13) 55 #define SD2_DRIVER_ENABLE IMX_GPIO_NR(7, 8) 56 57 struct i2c_pads_info i2c_pad_info3 = { 58 .scl = { 59 .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC, 60 .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC, 61 .gp = IMX_GPIO_NR(1, 5) 62 }, 63 .sda = { 64 .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC, 65 .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC, 66 .gp = IMX_GPIO_NR(1, 6) 67 } 68 }; 69 70 struct i2c_pads_info i2c_pad_info4 = { 71 .scl = { 72 .i2c_mode = MX6_PAD_GPIO_7__I2C4_SCL | PC, 73 .gpio_mode = MX6_PAD_GPIO_7__GPIO1_IO07 | PC, 74 .gp = IMX_GPIO_NR(1, 7) 75 }, 76 .sda = { 77 .i2c_mode = MX6_PAD_GPIO_8__I2C4_SDA | PC, 78 .gpio_mode = MX6_PAD_GPIO_8__GPIO1_IO08 | PC, 79 .gp = IMX_GPIO_NR(1, 8) 80 } 81 }; 82 83 iomux_v3_cfg_t const uart1_pads[] = { 84 MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 85 MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 86 MX6_PAD_EIM_D19__UART1_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 87 MX6_PAD_EIM_D20__UART1_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 88 }; 89 90 iomux_v3_cfg_t const uart2_pads[] = { 91 MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 92 MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 93 }; 94 95 iomux_v3_cfg_t const uart3_pads[] = { 96 MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 97 MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 98 MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 99 MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 100 }; 101 102 iomux_v3_cfg_t const uart4_pads[] = { 103 MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 104 MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 105 }; 106 107 iomux_v3_cfg_t const gpio_pads[] = { 108 /* LED enable*/ 109 MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL), 110 /* LED yellow */ 111 MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL), 112 /* LED red */ 113 #if (CONFIG_SYS_BOARD_VERSION == 2) 114 MX6_PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), 115 #elif (CONFIG_SYS_BOARD_VERSION == 3) 116 MX6_PAD_EIM_WAIT__GPIO5_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), 117 #endif 118 /* LED green */ 119 MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), 120 /* LED blue */ 121 MX6_PAD_EIM_EB1__GPIO2_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), 122 /* spi flash WP protect */ 123 MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), 124 /* spi CS 0 */ 125 MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), 126 /* spi bus #2 SS driver enable */ 127 MX6_PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), 128 /* RST_LOC# PHY reset input (has pull-down!)*/ 129 MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL), 130 /* SD 2 level shifter output enable */ 131 MX6_PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL), 132 /* SD1 card detect input */ 133 MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), 134 /* SD1 write protect input */ 135 MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL), 136 /* SD2 card detect input */ 137 MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), 138 /* SD2 write protect input */ 139 MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), 140 /* Touchscreen IRQ */ 141 MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL), 142 }; 143 144 static iomux_v3_cfg_t const misc_pads[] = { 145 /* USB_OTG_ID = GPIO1_24*/ 146 MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL), 147 /* H1 Power enable = GPIO1_0*/ 148 MX6_PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), 149 /* OTG Power enable = GPIO4_15*/ 150 MX6_PAD_KEY_ROW4__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), 151 }; 152 153 iomux_v3_cfg_t const enet_pads[] = { 154 MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 155 MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 156 MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 157 MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 158 MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 159 MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 160 MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 161 MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 162 MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), 163 MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 164 MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 165 MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 166 MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 167 MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 168 MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 169 }; 170 171 static iomux_v3_cfg_t const backlight_pads[] = { 172 /* backlight PWM brightness control */ 173 MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), 174 /* backlight enable */ 175 MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), 176 /* LCD power enable */ 177 MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), 178 }; 179 180 static iomux_v3_cfg_t const ecspi1_pads[] = { 181 MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), 182 MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), 183 MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), 184 #if (CONFIG_SYS_BOARD_VERSION == 2) 185 MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(SPI_PAD_CTRL), 186 #elif (CONFIG_SYS_BOARD_VERSION == 3) 187 MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(SPI_PAD_CTRL), 188 MX6_PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), 189 #endif 190 }; 191 192 static void setup_iomux_enet(void) 193 { 194 imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); 195 } 196 197 #if (CONFIG_SYS_BOARD_VERSION == 2) 198 iomux_v3_cfg_t const ecspi4_pads[] = { 199 MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL), 200 MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(NO_PAD_CTRL), 201 MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL), 202 MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), 203 MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), 204 }; 205 #endif 206 207 static iomux_v3_cfg_t const display_pads[] = { 208 MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL), 209 MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, 210 MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, 211 MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, 212 MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00, 213 MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01, 214 MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02, 215 MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03, 216 MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04, 217 MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05, 218 MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06, 219 MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07, 220 MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08, 221 MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09, 222 MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10, 223 MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11, 224 MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12, 225 MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13, 226 MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14, 227 MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15, 228 MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16, 229 MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17, 230 MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18, 231 MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19, 232 MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20, 233 MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21, 234 MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22, 235 MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23, 236 }; 237 238 int board_spi_cs_gpio(unsigned bus, unsigned cs) 239 { 240 if (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS) 241 #if (CONFIG_SYS_BOARD_VERSION == 2) 242 return IMX_GPIO_NR(5, 2); 243 244 if (bus == 0 && cs == 0) 245 return IMX_GPIO_NR(4, 9); 246 #elif (CONFIG_SYS_BOARD_VERSION == 3) 247 return ECSPI1_CS0; 248 249 if (bus == 0 && cs == 1) 250 return ECSPI1_CS1; 251 #endif 252 return -1; 253 } 254 255 static void setup_spi(void) 256 { 257 int i; 258 259 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); 260 261 #if (CONFIG_SYS_BOARD_VERSION == 2) 262 imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads)); 263 #endif 264 265 for (i = 0; i < 4; i++) 266 enable_spi_clk(true, i); 267 268 gpio_direction_output(ECSPI1_CS0, 1); 269 #if (CONFIG_SYS_BOARD_VERSION == 2) 270 gpio_direction_output(ECSPI4_CS1, 0); 271 /* set cs0 to high (second device on spi bus #4) */ 272 gpio_direction_output(ECSPI4_CS0, 1); 273 #elif (CONFIG_SYS_BOARD_VERSION == 3) 274 gpio_direction_output(ECSPI1_CS1, 1); 275 #endif 276 } 277 278 static void setup_iomux_uart(void) 279 { 280 switch (CONFIG_MXC_UART_BASE) { 281 case UART1_BASE: 282 imx_iomux_v3_setup_multiple_pads(uart1_pads, 283 ARRAY_SIZE(uart1_pads)); 284 break; 285 case UART2_BASE: 286 imx_iomux_v3_setup_multiple_pads(uart2_pads, 287 ARRAY_SIZE(uart2_pads)); 288 break; 289 case UART3_BASE: 290 imx_iomux_v3_setup_multiple_pads(uart3_pads, 291 ARRAY_SIZE(uart3_pads)); 292 break; 293 case UART4_BASE: 294 imx_iomux_v3_setup_multiple_pads(uart4_pads, 295 ARRAY_SIZE(uart4_pads)); 296 break; 297 } 298 } 299 300 int board_phy_config(struct phy_device *phydev) 301 { 302 /* control data pad skew - devaddr = 0x02, register = 0x04 */ 303 ksz9031_phy_extended_write(phydev, 0x02, 304 MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, 305 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 306 /* rx data pad skew - devaddr = 0x02, register = 0x05 */ 307 ksz9031_phy_extended_write(phydev, 0x02, 308 MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 309 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 310 /* tx data pad skew - devaddr = 0x02, register = 0x06 */ 311 ksz9031_phy_extended_write(phydev, 0x02, 312 MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, 313 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 314 /* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */ 315 ksz9031_phy_extended_write(phydev, 0x02, 316 MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, 317 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF); 318 319 if (phydev->drv->config) 320 phydev->drv->config(phydev); 321 322 return 0; 323 } 324 325 int board_eth_init(bd_t *bis) 326 { 327 setup_iomux_enet(); 328 return cpu_eth_init(bis); 329 } 330 331 static int rotate_logo_one(unsigned char *out, unsigned char *in) 332 { 333 int i, j; 334 335 for (i = 0; i < BMP_LOGO_WIDTH; i++) 336 for (j = 0; j < BMP_LOGO_HEIGHT; j++) 337 out[j * BMP_LOGO_WIDTH + BMP_LOGO_HEIGHT - 1 - i] = 338 in[i * BMP_LOGO_WIDTH + j]; 339 return 0; 340 } 341 342 /* 343 * Rotate the BMP_LOGO (only) 344 * Will only work, if the logo is square, as 345 * BMP_LOGO_HEIGHT and BMP_LOGO_WIDTH are defines, not variables 346 */ 347 void rotate_logo(int rotations) 348 { 349 unsigned char out_logo[BMP_LOGO_WIDTH * BMP_LOGO_HEIGHT]; 350 unsigned char *in_logo; 351 int i, j; 352 353 if (BMP_LOGO_WIDTH != BMP_LOGO_HEIGHT) 354 return; 355 356 in_logo = bmp_logo_bitmap; 357 358 /* one 90 degree rotation */ 359 if (rotations == 1 || rotations == 2 || rotations == 3) 360 rotate_logo_one(out_logo, in_logo); 361 362 /* second 90 degree rotation */ 363 if (rotations == 2 || rotations == 3) 364 rotate_logo_one(in_logo, out_logo); 365 366 /* third 90 degree rotation */ 367 if (rotations == 3) 368 rotate_logo_one(out_logo, in_logo); 369 370 /* copy result back to original array */ 371 if (rotations == 1 || rotations == 3) 372 for (i = 0; i < BMP_LOGO_WIDTH; i++) 373 for (j = 0; j < BMP_LOGO_HEIGHT; j++) 374 in_logo[i * BMP_LOGO_WIDTH + j] = 375 out_logo[i * BMP_LOGO_WIDTH + j]; 376 } 377 378 static void enable_display_power(void) 379 { 380 imx_iomux_v3_setup_multiple_pads(backlight_pads, 381 ARRAY_SIZE(backlight_pads)); 382 383 /* backlight enable */ 384 gpio_direction_output(IMX_GPIO_NR(6, 31), 1); 385 /* LCD power enable */ 386 gpio_direction_output(IMX_GPIO_NR(6, 15), 1); 387 388 /* enable backlight PWM 1 */ 389 if (pwm_init(0, 0, 0)) 390 goto error; 391 /* duty cycle 500ns, period: 3000ns */ 392 if (pwm_config(0, 50000, 300000)) 393 goto error; 394 if (pwm_enable(0)) 395 goto error; 396 return; 397 398 error: 399 puts("error init pwm for backlight\n"); 400 return; 401 } 402 403 static void enable_lvds(struct display_info_t const *dev) 404 { 405 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 406 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 407 int reg; 408 s32 timeout = 100000; 409 410 /* set PLL5 clock */ 411 reg = readl(&ccm->analog_pll_video); 412 reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN; 413 writel(reg, &ccm->analog_pll_video); 414 415 /* set PLL5 to 232720000Hz */ 416 reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT; 417 reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x26); 418 reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT; 419 reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0); 420 writel(reg, &ccm->analog_pll_video); 421 422 writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xC0238), 423 &ccm->analog_pll_video_num); 424 writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xF4240), 425 &ccm->analog_pll_video_denom); 426 427 reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN; 428 writel(reg, &ccm->analog_pll_video); 429 430 while (timeout--) 431 if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK) 432 break; 433 if (timeout < 0) 434 printf("Warning: video pll lock timeout!\n"); 435 436 reg = readl(&ccm->analog_pll_video); 437 reg |= BM_ANADIG_PLL_VIDEO_ENABLE; 438 reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS; 439 writel(reg, &ccm->analog_pll_video); 440 441 /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */ 442 reg = readl(&ccm->cs2cdr); 443 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK 444 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 445 reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) 446 | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); 447 writel(reg, &ccm->cs2cdr); 448 449 reg = readl(&ccm->cscmr2); 450 reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; 451 writel(reg, &ccm->cscmr2); 452 453 reg = readl(&ccm->chsccdr); 454 reg |= (CHSCCDR_CLK_SEL_LDB_DI0 455 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); 456 writel(reg, &ccm->chsccdr); 457 458 reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES 459 | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH 460 | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH 461 | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG 462 | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT 463 | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED 464 | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; 465 writel(reg, &iomux->gpr[2]); 466 467 reg = readl(&iomux->gpr[3]); 468 reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK) 469 | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 470 << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); 471 writel(reg, &iomux->gpr[3]); 472 473 return; 474 } 475 476 static void enable_spi_display(struct display_info_t const *dev) 477 { 478 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 479 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 480 int reg; 481 s32 timeout = 100000; 482 483 #if defined(CONFIG_VIDEO_BMP_LOGO) 484 rotate_logo(3); /* portrait display in landscape mode */ 485 #endif 486 487 /* 488 * set ldb clock to 28341000 Hz calculated through the formula: 489 * (XRES + LEFT_M + RIGHT_M + HSYNC_LEN) * 490 * (YRES + UPPER_M + LOWER_M + VSYNC_LEN) * REFRESH) 491 * see: 492 * https://community.freescale.com/thread/308170 493 */ 494 ipu_set_ldb_clock(28341000); 495 496 reg = readl(&ccm->cs2cdr); 497 498 /* select pll 5 clock */ 499 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK 500 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 501 writel(reg, &ccm->cs2cdr); 502 503 /* set PLL5 to 197994996Hz */ 504 reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT; 505 reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x21); 506 reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT; 507 reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0); 508 writel(reg, &ccm->analog_pll_video); 509 510 writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xfbf4), 511 &ccm->analog_pll_video_num); 512 writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xf4240), 513 &ccm->analog_pll_video_denom); 514 515 reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN; 516 writel(reg, &ccm->analog_pll_video); 517 518 while (timeout--) 519 if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK) 520 break; 521 if (timeout < 0) 522 printf("Warning: video pll lock timeout!\n"); 523 524 reg = readl(&ccm->analog_pll_video); 525 reg |= BM_ANADIG_PLL_VIDEO_ENABLE; 526 reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS; 527 writel(reg, &ccm->analog_pll_video); 528 529 /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */ 530 reg = readl(&ccm->cs2cdr); 531 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK 532 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 533 reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) 534 | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); 535 writel(reg, &ccm->cs2cdr); 536 537 reg = readl(&ccm->cscmr2); 538 reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; 539 writel(reg, &ccm->cscmr2); 540 541 reg = readl(&ccm->chsccdr); 542 reg |= (CHSCCDR_CLK_SEL_LDB_DI0 543 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); 544 reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK; 545 reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET); 546 reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK; 547 reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET); 548 writel(reg, &ccm->chsccdr); 549 550 reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES 551 | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH 552 | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH 553 | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG 554 | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT 555 | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED 556 | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; 557 writel(reg, &iomux->gpr[2]); 558 559 reg = readl(&iomux->gpr[3]); 560 reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK) 561 | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 562 << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); 563 writel(reg, &iomux->gpr[3]); 564 565 imx_iomux_v3_setup_multiple_pads( 566 display_pads, 567 ARRAY_SIZE(display_pads)); 568 569 return; 570 } 571 static void setup_display(void) 572 { 573 enable_ipu_clock(); 574 enable_display_power(); 575 } 576 577 static void setup_iomux_gpio(void) 578 { 579 imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads)); 580 } 581 582 static void set_gpr_register(void) 583 { 584 struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 585 586 writel(IOMUXC_GPR1_APP_CLK_REQ_N | IOMUXC_GPR1_PCIE_RDY_L23 | 587 IOMUXC_GPR1_EXC_MON_SLVE | 588 (2 << IOMUXC_GPR1_ADDRS0_OFFSET) | 589 IOMUXC_GPR1_ACT_CS0, 590 &iomuxc_regs->gpr[1]); 591 writel(0x0, &iomuxc_regs->gpr[8]); 592 writel(IOMUXC_GPR12_ARMP_IPG_CLK_EN | IOMUXC_GPR12_ARMP_AHB_CLK_EN | 593 IOMUXC_GPR12_ARMP_ATB_CLK_EN | IOMUXC_GPR12_ARMP_APB_CLK_EN, 594 &iomuxc_regs->gpr[12]); 595 } 596 597 int board_early_init_f(void) 598 { 599 setup_iomux_uart(); 600 setup_iomux_gpio(); 601 602 gpio_direction_output(SOFT_RESET_GPIO, 1); 603 gpio_direction_output(SD2_DRIVER_ENABLE, 1); 604 setup_display(); 605 set_gpr_register(); 606 return 0; 607 } 608 609 static void setup_i2c4(void) 610 { 611 setup_i2c(3, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 612 &i2c_pad_info4); 613 } 614 615 static void setup_board_gpio(void) 616 { 617 /* enable all LEDs */ 618 gpio_request(IMX_GPIO_NR(2, 13), "LED ena"); /* 25 */ 619 gpio_direction_output(IMX_GPIO_NR(1, 25), 0); 620 621 /* switch off Status LEDs */ 622 #if (CONFIG_SYS_BOARD_VERSION == 2) 623 gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */ 624 gpio_direction_output(IMX_GPIO_NR(6, 16), 1); 625 gpio_request(IMX_GPIO_NR(2, 28), "LED red"); /* 60 */ 626 gpio_direction_output(IMX_GPIO_NR(2, 28), 1); 627 gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */ 628 gpio_direction_output(IMX_GPIO_NR(5, 4), 1); 629 gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */ 630 gpio_direction_output(IMX_GPIO_NR(2, 29), 1); 631 #elif (CONFIG_SYS_BOARD_VERSION == 3) 632 gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */ 633 gpio_direction_output(IMX_GPIO_NR(6, 16), 0); 634 gpio_request(IMX_GPIO_NR(5, 0), "LED red"); /* 128 */ 635 gpio_direction_output(IMX_GPIO_NR(5, 0), 0); 636 gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */ 637 gpio_direction_output(IMX_GPIO_NR(5, 4), 0); 638 gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */ 639 gpio_direction_output(IMX_GPIO_NR(2, 29), 0); 640 #endif 641 } 642 643 static void setup_board_spi(void) 644 { 645 /* enable spi bus #2 SS drivers (and spi bus #4 SS1 for rev2b) */ 646 gpio_direction_output(IMX_GPIO_NR(6, 6), 1); 647 } 648 649 int board_late_init(void) 650 { 651 char *my_bootdelay; 652 char bootmode = 0; 653 char const *panel = env_get("panel"); 654 655 /* 656 * Check the boot-source. If booting from NOR Flash, 657 * disable bootdelay 658 */ 659 gpio_request(IMX_GPIO_NR(7, 6), "bootsel0"); 660 gpio_direction_input(IMX_GPIO_NR(7, 6)); 661 gpio_request(IMX_GPIO_NR(7, 7), "bootsel1"); 662 gpio_direction_input(IMX_GPIO_NR(7, 7)); 663 gpio_request(IMX_GPIO_NR(7, 1), "bootsel2"); 664 gpio_direction_input(IMX_GPIO_NR(7, 1)); 665 bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 6)) ? 1 : 0) << 0; 666 bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 7)) ? 1 : 0) << 1; 667 bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 1)) ? 1 : 0) << 2; 668 669 if (bootmode == 7) { 670 my_bootdelay = env_get("nor_bootdelay"); 671 if (my_bootdelay != NULL) 672 env_set("bootdelay", my_bootdelay); 673 else 674 env_set("bootdelay", "-2"); 675 } 676 677 /* if we have the lg panel, we can initialze it now */ 678 if (panel) 679 if (!strcmp(panel, displays[1].mode.name)) 680 lg4573_spi_startup(CONFIG_LG4573_BUS, 681 CONFIG_LG4573_CS, 682 10000000, SPI_MODE_0); 683 684 return 0; 685 } 686