1 /* 2 * (C) Copyright 2015 3 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 4 * 5 * Based on: 6 * Copyright (C) 2012 Freescale Semiconductor, Inc. 7 * 8 * Author: Fabio Estevam <fabio.estevam@freescale.com> 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #include <asm/arch/clock.h> 14 #include <asm/arch/imx-regs.h> 15 #include <asm/arch/iomux.h> 16 #include <asm/arch/mx6-pins.h> 17 #include <asm/errno.h> 18 #include <asm/gpio.h> 19 #include <asm/imx-common/iomux-v3.h> 20 #include <asm/imx-common/boot_mode.h> 21 #include <asm/imx-common/mxc_i2c.h> 22 #include <asm/imx-common/video.h> 23 #include <mmc.h> 24 #include <fsl_esdhc.h> 25 #include <miiphy.h> 26 #include <netdev.h> 27 #include <asm/arch/mxc_hdmi.h> 28 #include <asm/arch/crm_regs.h> 29 #include <linux/fb.h> 30 #include <ipu_pixfmt.h> 31 #include <asm/io.h> 32 #include <asm/arch/sys_proto.h> 33 #include <pwm.h> 34 #include <micrel.h> 35 #include <spi.h> 36 #include <video.h> 37 #include <../drivers/video/ipu.h> 38 #if defined(CONFIG_VIDEO_BMP_LOGO) 39 #include <bmp_logo.h> 40 #endif 41 42 #define USDHC2_PAD_CTRL (PAD_CTL_SPEED_LOW | \ 43 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) 44 45 #if (CONFIG_SYS_BOARD_VERSION == 2) 46 /* 4.3 display controller */ 47 #define ECSPI1_CS0 IMX_GPIO_NR(4, 9) 48 #define ECSPI4_CS0 IMX_GPIO_NR(3, 29) 49 #elif (CONFIG_SYS_BOARD_VERSION == 3) 50 #define ECSPI1_CS0 IMX_GPIO_NR(2, 30) /* NOR flash */ 51 /* 4.3 display controller */ 52 #define ECSPI1_CS1 IMX_GPIO_NR(4, 10) 53 #endif 54 55 #define SOFT_RESET_GPIO IMX_GPIO_NR(7, 13) 56 #define SD2_DRIVER_ENABLE IMX_GPIO_NR(7, 8) 57 58 struct i2c_pads_info i2c_pad_info3 = { 59 .scl = { 60 .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC, 61 .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC, 62 .gp = IMX_GPIO_NR(1, 5) 63 }, 64 .sda = { 65 .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC, 66 .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC, 67 .gp = IMX_GPIO_NR(1, 6) 68 } 69 }; 70 71 struct i2c_pads_info i2c_pad_info4 = { 72 .scl = { 73 .i2c_mode = MX6_PAD_GPIO_7__I2C4_SCL | PC, 74 .gpio_mode = MX6_PAD_GPIO_7__GPIO1_IO07 | PC, 75 .gp = IMX_GPIO_NR(1, 7) 76 }, 77 .sda = { 78 .i2c_mode = MX6_PAD_GPIO_8__I2C4_SDA | PC, 79 .gpio_mode = MX6_PAD_GPIO_8__GPIO1_IO08 | PC, 80 .gp = IMX_GPIO_NR(1, 8) 81 } 82 }; 83 84 iomux_v3_cfg_t const uart1_pads[] = { 85 MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 86 MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 87 MX6_PAD_EIM_D19__UART1_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 88 MX6_PAD_EIM_D20__UART1_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 89 }; 90 91 iomux_v3_cfg_t const uart2_pads[] = { 92 MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 93 MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 94 }; 95 96 iomux_v3_cfg_t const uart3_pads[] = { 97 MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 98 MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 99 MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 100 MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), 101 }; 102 103 iomux_v3_cfg_t const uart4_pads[] = { 104 MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 105 MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), 106 }; 107 108 iomux_v3_cfg_t const gpio_pads[] = { 109 /* LED enable*/ 110 MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL), 111 /* LED yellow */ 112 MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL), 113 /* LED red */ 114 #if (CONFIG_SYS_BOARD_VERSION == 2) 115 MX6_PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), 116 #elif (CONFIG_SYS_BOARD_VERSION == 3) 117 MX6_PAD_EIM_WAIT__GPIO5_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), 118 #endif 119 /* LED green */ 120 MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), 121 /* LED blue */ 122 MX6_PAD_EIM_EB1__GPIO2_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), 123 /* spi flash WP protect */ 124 MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), 125 /* spi CS 0 */ 126 MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), 127 /* spi bus #2 SS driver enable */ 128 MX6_PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), 129 /* RST_LOC# PHY reset input (has pull-down!)*/ 130 MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL), 131 /* SD 2 level shifter output enable */ 132 MX6_PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL), 133 /* SD1 card detect input */ 134 MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), 135 /* SD1 write protect input */ 136 MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL), 137 /* SD2 card detect input */ 138 MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), 139 /* SD2 write protect input */ 140 MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), 141 /* Touchscreen IRQ */ 142 MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL), 143 }; 144 145 static iomux_v3_cfg_t const misc_pads[] = { 146 /* USB_OTG_ID = GPIO1_24*/ 147 MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL), 148 /* H1 Power enable = GPIO1_0*/ 149 MX6_PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), 150 /* OTG Power enable = GPIO4_15*/ 151 MX6_PAD_KEY_ROW4__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), 152 }; 153 154 iomux_v3_cfg_t const enet_pads[] = { 155 MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), 156 MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), 157 MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 158 MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 159 MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 160 MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 161 MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 162 MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 163 MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), 164 MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), 165 MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), 166 MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), 167 MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), 168 MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), 169 MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), 170 }; 171 172 static iomux_v3_cfg_t const backlight_pads[] = { 173 /* backlight PWM brightness control */ 174 MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), 175 /* backlight enable */ 176 MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), 177 /* LCD power enable */ 178 MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), 179 }; 180 181 static iomux_v3_cfg_t const ecspi1_pads[] = { 182 MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), 183 MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), 184 MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), 185 #if (CONFIG_SYS_BOARD_VERSION == 2) 186 MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(SPI_PAD_CTRL), 187 #elif (CONFIG_SYS_BOARD_VERSION == 3) 188 MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(SPI_PAD_CTRL), 189 MX6_PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), 190 #endif 191 }; 192 193 static void setup_iomux_enet(void) 194 { 195 imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); 196 } 197 198 #if (CONFIG_SYS_BOARD_VERSION == 2) 199 iomux_v3_cfg_t const ecspi4_pads[] = { 200 MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL), 201 MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(NO_PAD_CTRL), 202 MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL), 203 MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), 204 MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), 205 }; 206 #endif 207 208 static iomux_v3_cfg_t const display_pads[] = { 209 MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL), 210 MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, 211 MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, 212 MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, 213 MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00, 214 MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01, 215 MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02, 216 MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03, 217 MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04, 218 MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05, 219 MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06, 220 MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07, 221 MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08, 222 MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09, 223 MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10, 224 MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11, 225 MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12, 226 MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13, 227 MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14, 228 MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15, 229 MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16, 230 MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17, 231 MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18, 232 MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19, 233 MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20, 234 MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21, 235 MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22, 236 MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23, 237 }; 238 239 int board_spi_cs_gpio(unsigned bus, unsigned cs) 240 { 241 if (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS) 242 #if (CONFIG_SYS_BOARD_VERSION == 2) 243 return IMX_GPIO_NR(5, 2); 244 245 if (bus == 0 && cs == 0) 246 return IMX_GPIO_NR(4, 9); 247 #elif (CONFIG_SYS_BOARD_VERSION == 3) 248 return ECSPI1_CS0; 249 250 if (bus == 0 && cs == 1) 251 return ECSPI1_CS1; 252 #endif 253 return -1; 254 } 255 256 static void setup_spi(void) 257 { 258 int i; 259 260 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); 261 262 #if (CONFIG_SYS_BOARD_VERSION == 2) 263 imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads)); 264 #endif 265 266 for (i = 0; i < 4; i++) 267 enable_spi_clk(true, i); 268 269 gpio_direction_output(ECSPI1_CS0, 1); 270 #if (CONFIG_SYS_BOARD_VERSION == 2) 271 gpio_direction_output(ECSPI4_CS1, 0); 272 /* set cs0 to high (second device on spi bus #4) */ 273 gpio_direction_output(ECSPI4_CS0, 1); 274 #elif (CONFIG_SYS_BOARD_VERSION == 3) 275 gpio_direction_output(ECSPI1_CS1, 1); 276 #endif 277 } 278 279 static void setup_iomux_uart(void) 280 { 281 switch (CONFIG_MXC_UART_BASE) { 282 case UART1_BASE: 283 imx_iomux_v3_setup_multiple_pads(uart1_pads, 284 ARRAY_SIZE(uart1_pads)); 285 break; 286 case UART2_BASE: 287 imx_iomux_v3_setup_multiple_pads(uart2_pads, 288 ARRAY_SIZE(uart2_pads)); 289 break; 290 case UART3_BASE: 291 imx_iomux_v3_setup_multiple_pads(uart3_pads, 292 ARRAY_SIZE(uart3_pads)); 293 break; 294 case UART4_BASE: 295 imx_iomux_v3_setup_multiple_pads(uart4_pads, 296 ARRAY_SIZE(uart4_pads)); 297 break; 298 } 299 } 300 301 int board_phy_config(struct phy_device *phydev) 302 { 303 /* control data pad skew - devaddr = 0x02, register = 0x04 */ 304 ksz9031_phy_extended_write(phydev, 0x02, 305 MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, 306 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 307 /* rx data pad skew - devaddr = 0x02, register = 0x05 */ 308 ksz9031_phy_extended_write(phydev, 0x02, 309 MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 310 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 311 /* tx data pad skew - devaddr = 0x02, register = 0x06 */ 312 ksz9031_phy_extended_write(phydev, 0x02, 313 MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, 314 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000); 315 /* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */ 316 ksz9031_phy_extended_write(phydev, 0x02, 317 MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, 318 MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF); 319 320 if (phydev->drv->config) 321 phydev->drv->config(phydev); 322 323 return 0; 324 } 325 326 int board_eth_init(bd_t *bis) 327 { 328 setup_iomux_enet(); 329 return cpu_eth_init(bis); 330 } 331 332 static int rotate_logo_one(unsigned char *out, unsigned char *in) 333 { 334 int i, j; 335 336 for (i = 0; i < BMP_LOGO_WIDTH; i++) 337 for (j = 0; j < BMP_LOGO_HEIGHT; j++) 338 out[j * BMP_LOGO_WIDTH + BMP_LOGO_HEIGHT - 1 - i] = 339 in[i * BMP_LOGO_WIDTH + j]; 340 return 0; 341 } 342 343 /* 344 * Rotate the BMP_LOGO (only) 345 * Will only work, if the logo is square, as 346 * BMP_LOGO_HEIGHT and BMP_LOGO_WIDTH are defines, not variables 347 */ 348 void rotate_logo(int rotations) 349 { 350 unsigned char out_logo[BMP_LOGO_WIDTH * BMP_LOGO_HEIGHT]; 351 unsigned char *in_logo; 352 int i, j; 353 354 if (BMP_LOGO_WIDTH != BMP_LOGO_HEIGHT) 355 return; 356 357 in_logo = bmp_logo_bitmap; 358 359 /* one 90 degree rotation */ 360 if (rotations == 1 || rotations == 2 || rotations == 3) 361 rotate_logo_one(out_logo, in_logo); 362 363 /* second 90 degree rotation */ 364 if (rotations == 2 || rotations == 3) 365 rotate_logo_one(in_logo, out_logo); 366 367 /* third 90 degree rotation */ 368 if (rotations == 3) 369 rotate_logo_one(out_logo, in_logo); 370 371 /* copy result back to original array */ 372 if (rotations == 1 || rotations == 3) 373 for (i = 0; i < BMP_LOGO_WIDTH; i++) 374 for (j = 0; j < BMP_LOGO_HEIGHT; j++) 375 in_logo[i * BMP_LOGO_WIDTH + j] = 376 out_logo[i * BMP_LOGO_WIDTH + j]; 377 } 378 379 static void enable_display_power(void) 380 { 381 imx_iomux_v3_setup_multiple_pads(backlight_pads, 382 ARRAY_SIZE(backlight_pads)); 383 384 /* backlight enable */ 385 gpio_direction_output(IMX_GPIO_NR(6, 31), 1); 386 /* LCD power enable */ 387 gpio_direction_output(IMX_GPIO_NR(6, 15), 1); 388 389 /* enable backlight PWM 1 */ 390 if (pwm_init(0, 0, 0)) 391 goto error; 392 /* duty cycle 500ns, period: 3000ns */ 393 if (pwm_config(0, 50000, 300000)) 394 goto error; 395 if (pwm_enable(0)) 396 goto error; 397 return; 398 399 error: 400 puts("error init pwm for backlight\n"); 401 return; 402 } 403 404 static void enable_lvds(struct display_info_t const *dev) 405 { 406 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 407 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 408 int reg; 409 s32 timeout = 100000; 410 411 /* set PLL5 clock */ 412 reg = readl(&ccm->analog_pll_video); 413 reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN; 414 writel(reg, &ccm->analog_pll_video); 415 416 /* set PLL5 to 232720000Hz */ 417 reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT; 418 reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x26); 419 reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT; 420 reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0); 421 writel(reg, &ccm->analog_pll_video); 422 423 writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xC0238), 424 &ccm->analog_pll_video_num); 425 writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xF4240), 426 &ccm->analog_pll_video_denom); 427 428 reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN; 429 writel(reg, &ccm->analog_pll_video); 430 431 while (timeout--) 432 if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK) 433 break; 434 if (timeout < 0) 435 printf("Warning: video pll lock timeout!\n"); 436 437 reg = readl(&ccm->analog_pll_video); 438 reg |= BM_ANADIG_PLL_VIDEO_ENABLE; 439 reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS; 440 writel(reg, &ccm->analog_pll_video); 441 442 /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */ 443 reg = readl(&ccm->cs2cdr); 444 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK 445 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 446 reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) 447 | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); 448 writel(reg, &ccm->cs2cdr); 449 450 reg = readl(&ccm->cscmr2); 451 reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; 452 writel(reg, &ccm->cscmr2); 453 454 reg = readl(&ccm->chsccdr); 455 reg |= (CHSCCDR_CLK_SEL_LDB_DI0 456 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); 457 writel(reg, &ccm->chsccdr); 458 459 reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES 460 | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH 461 | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH 462 | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG 463 | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT 464 | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED 465 | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; 466 writel(reg, &iomux->gpr[2]); 467 468 reg = readl(&iomux->gpr[3]); 469 reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK) 470 | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 471 << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); 472 writel(reg, &iomux->gpr[3]); 473 474 return; 475 } 476 477 static void enable_spi_display(struct display_info_t const *dev) 478 { 479 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 480 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 481 int reg; 482 s32 timeout = 100000; 483 484 #if defined(CONFIG_VIDEO_BMP_LOGO) 485 rotate_logo(3); /* portrait display in landscape mode */ 486 #endif 487 488 /* 489 * set ldb clock to 28341000 Hz calculated through the formula: 490 * (XRES + LEFT_M + RIGHT_M + HSYNC_LEN) * 491 * (YRES + UPPER_M + LOWER_M + VSYNC_LEN) * REFRESH) 492 * see: 493 * https://community.freescale.com/thread/308170 494 */ 495 ipu_set_ldb_clock(28341000); 496 497 reg = readl(&ccm->cs2cdr); 498 499 /* select pll 5 clock */ 500 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK 501 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 502 writel(reg, &ccm->cs2cdr); 503 504 /* set PLL5 to 197994996Hz */ 505 reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT; 506 reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x21); 507 reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT; 508 reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0); 509 writel(reg, &ccm->analog_pll_video); 510 511 writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xfbf4), 512 &ccm->analog_pll_video_num); 513 writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xf4240), 514 &ccm->analog_pll_video_denom); 515 516 reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN; 517 writel(reg, &ccm->analog_pll_video); 518 519 while (timeout--) 520 if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK) 521 break; 522 if (timeout < 0) 523 printf("Warning: video pll lock timeout!\n"); 524 525 reg = readl(&ccm->analog_pll_video); 526 reg |= BM_ANADIG_PLL_VIDEO_ENABLE; 527 reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS; 528 writel(reg, &ccm->analog_pll_video); 529 530 /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */ 531 reg = readl(&ccm->cs2cdr); 532 reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK 533 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); 534 reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) 535 | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); 536 writel(reg, &ccm->cs2cdr); 537 538 reg = readl(&ccm->cscmr2); 539 reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; 540 writel(reg, &ccm->cscmr2); 541 542 reg = readl(&ccm->chsccdr); 543 reg |= (CHSCCDR_CLK_SEL_LDB_DI0 544 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); 545 reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK; 546 reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET); 547 reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK; 548 reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET); 549 writel(reg, &ccm->chsccdr); 550 551 reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES 552 | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH 553 | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH 554 | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG 555 | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT 556 | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED 557 | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; 558 writel(reg, &iomux->gpr[2]); 559 560 reg = readl(&iomux->gpr[3]); 561 reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK) 562 | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 563 << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); 564 writel(reg, &iomux->gpr[3]); 565 566 imx_iomux_v3_setup_multiple_pads( 567 display_pads, 568 ARRAY_SIZE(display_pads)); 569 570 return; 571 } 572 static void setup_display(void) 573 { 574 enable_ipu_clock(); 575 enable_display_power(); 576 } 577 578 static void setup_iomux_gpio(void) 579 { 580 imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads)); 581 } 582 583 static void set_gpr_register(void) 584 { 585 struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 586 587 writel(IOMUXC_GPR1_APP_CLK_REQ_N | IOMUXC_GPR1_PCIE_RDY_L23 | 588 IOMUXC_GPR1_EXC_MON_SLVE | 589 (2 << IOMUXC_GPR1_ADDRS0_OFFSET) | 590 IOMUXC_GPR1_ACT_CS0, 591 &iomuxc_regs->gpr[1]); 592 writel(0x0, &iomuxc_regs->gpr[8]); 593 writel(IOMUXC_GPR12_ARMP_IPG_CLK_EN | IOMUXC_GPR12_ARMP_AHB_CLK_EN | 594 IOMUXC_GPR12_ARMP_ATB_CLK_EN | IOMUXC_GPR12_ARMP_APB_CLK_EN, 595 &iomuxc_regs->gpr[12]); 596 } 597 598 int board_early_init_f(void) 599 { 600 setup_iomux_uart(); 601 setup_iomux_gpio(); 602 603 gpio_direction_output(SOFT_RESET_GPIO, 1); 604 gpio_direction_output(SD2_DRIVER_ENABLE, 1); 605 setup_display(); 606 set_gpr_register(); 607 return 0; 608 } 609 610 static void setup_i2c4(void) 611 { 612 setup_i2c(3, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 613 &i2c_pad_info4); 614 } 615 616 static void setup_board_gpio(void) 617 { 618 /* enable all LEDs */ 619 gpio_request(IMX_GPIO_NR(2, 13), "LED ena"); /* 25 */ 620 gpio_direction_output(IMX_GPIO_NR(1, 25), 0); 621 622 /* switch off Status LEDs */ 623 #if (CONFIG_SYS_BOARD_VERSION == 2) 624 gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */ 625 gpio_direction_output(IMX_GPIO_NR(6, 16), 1); 626 gpio_request(IMX_GPIO_NR(2, 28), "LED red"); /* 60 */ 627 gpio_direction_output(IMX_GPIO_NR(2, 28), 1); 628 gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */ 629 gpio_direction_output(IMX_GPIO_NR(5, 4), 1); 630 gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */ 631 gpio_direction_output(IMX_GPIO_NR(2, 29), 1); 632 #elif (CONFIG_SYS_BOARD_VERSION == 3) 633 gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */ 634 gpio_direction_output(IMX_GPIO_NR(6, 16), 0); 635 gpio_request(IMX_GPIO_NR(5, 0), "LED red"); /* 128 */ 636 gpio_direction_output(IMX_GPIO_NR(5, 0), 0); 637 gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */ 638 gpio_direction_output(IMX_GPIO_NR(5, 4), 0); 639 gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */ 640 gpio_direction_output(IMX_GPIO_NR(2, 29), 0); 641 #endif 642 } 643 644 static void setup_board_spi(void) 645 { 646 /* enable spi bus #2 SS drivers (and spi bus #4 SS1 for rev2b) */ 647 gpio_direction_output(IMX_GPIO_NR(6, 6), 1); 648 } 649 650 int board_late_init(void) 651 { 652 char *my_bootdelay; 653 char bootmode = 0; 654 char const *panel = getenv("panel"); 655 656 /* 657 * Check the boot-source. If booting from NOR Flash, 658 * disable bootdelay 659 */ 660 gpio_request(IMX_GPIO_NR(7, 6), "bootsel0"); 661 gpio_direction_input(IMX_GPIO_NR(7, 6)); 662 gpio_request(IMX_GPIO_NR(7, 7), "bootsel1"); 663 gpio_direction_input(IMX_GPIO_NR(7, 7)); 664 gpio_request(IMX_GPIO_NR(7, 1), "bootsel2"); 665 gpio_direction_input(IMX_GPIO_NR(7, 1)); 666 bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 6)) ? 1 : 0) << 0; 667 bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 7)) ? 1 : 0) << 1; 668 bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 1)) ? 1 : 0) << 2; 669 670 if (bootmode == 7) { 671 my_bootdelay = getenv("nor_bootdelay"); 672 if (my_bootdelay != NULL) 673 setenv("bootdelay", my_bootdelay); 674 else 675 setenv("bootdelay", "-2"); 676 } 677 678 /* if we have the lg panel, we can initialze it now */ 679 if (panel) 680 if (!strcmp(panel, displays[1].mode.name)) 681 lg4573_spi_startup(CONFIG_LG4573_BUS, 682 CONFIG_LG4573_CS, 683 10000000, SPI_MODE_0); 684 685 return 0; 686 } 687